Kohler Loure T97330-4-CP Bedienungsanleitung

Installation Instructions

Floor-Mount Bath Faucet

Français, page “Français-1”

Español, página “Español-1”

1443289-2-A

Tools and Materials

Important Information

CAUTION: Risk of personal injury. Do not use the bath

filler as a grab bar or support bar when entering or exiting

the bath. The bath filler is not designed to support weight.

NOTICE: To avoid damage to the O-rings on the bottom of the

faucet, keep the faucet vertical and use care when installing the

faucet.

NOTE: A minimum operating pressure of 45 psi (310 kPa) is

required for proper operation. If a pressure of less than 45 psi (310

kPa) is present, contact a plumber or choose another faucet.

For use with automatic compensating valves rated at 1.6 gal/min

(6.1 l/min) or less.

Follow all local plumbing and building codes.

Turn OFF the water supply.

A drill bit is provided for installation to wood support. Use an

appropriate drill bit for other materials.

The dimensions given assume the spout and bath are mounted on

the same surface. Adjust the dimensions accordingly if the spout

and bath are mounted on different surfaces.

If this product is installed with an overflowing bath, the outer rim

of the bath should slightly overlap the 2x4 framing.

Installer supplied copper tubing must be 5/8″OD (1/2″

Nominal).

Carefully review this document and any appropriate rough-in

sheets. Design the bath enclosure accordingly.

Sealant Tape

Plus:

• 3/16" Masonry Bit (for concrete installation)

• Conventional Woodworking Tools

• Plumbing Tools and Materials

1443289-2-A 2 Kohler Co.

Important Information (cont.)

The appearance of your faucet may differ from the illustrations in

this guide. The instructions still apply.

Kohler Co. 3 1443289-2-A

1. Prepare the Site

IMPORTANT! 2x6 lumber is NOT adequate for this application.

Finished

Wall

7-7/8"

(200 mm)

Min

Finished

Floor

2-3/4"

(70 mm)

Min

Bath

Base

Centerline

1443289-2-A 4 Kohler Co.

Top of the

Finished Floor

2-3/8"

(60 mm) Min

3-3/16"

(81mm) Max

Wood Support

Floor Joist

Prepare the Site (cont.)

NOTICE: Adequate floor support is required. The wood support

must be a minimum of 2″(51 mm) thick by 6″(152 mm) wide. 2x6

lumber is NOT adequate for this application.

NOTE: Concrete can be used as the floor support.

Plan out the bath filler placement based on the dimensions above.

Cut a hole in the subfloor large enough to install the wood support

between two floor joists.

Secure the wood support between 2-3/8″ (60 mm) to 3-3/16″ (81 mm)

below the top of the finished floor.

Kohler Co. 5 1443289-2-A

2. Spout Orientation

NOTE: Verify correct spout orientation before securing the base to

the wooden support.

NOTE: The base has a blue mark and a notch on the cold supply

side.

Orient the base with the cold supply side notch placed in the

direction shown.

If possible, dry fit the faucet to the base using the screws and

washers. Orient the spout to the inside of the bath.

If your faucet is not available at this time, make sure the base is

positioned so the faucet will properly run water into the bath.

Mark the mounting hole locations on the wooden support.

Mark the orientation of the base and where the notch is

positioned on the wooden support.

Top View

Bath

Hot

Pencil

Wall

Cold

1443289-2-A 6 Kohler Co.

3. Install the Base

If attached, remove the faucet from the base.

Drill 1-1/2″(380 mm) deep holes with a 3/16″drill bit (provided)

using the marked locations as the center point.

If using concrete as the floor support, drill 1-1/2″(380 mm) deep

holes with a 3/16″masonry bit (not provided).

Realign the base to the position you marked. Make sure the cold

supply side notch is in the correct orientation.

Secure the base to the support with the screws and washers

provided.

Verify the base is level and tighten the screws.

Floor

Joist

Wood

Support

3/16"

Mounting

Hole

Base

Washer

Screw

Kohler Co. 7 1443289-2-A

4. Connect the Supplies

NOTE: The base has a blue mark and a notch on the cold supply

side.

Apply sealant tape on the ½″ NPT hot and cold supply pipes and

thread into the base.

Insert the plugs into the base.

Turn ON the water supply and check for leaks.

Turn OFF the water supply.

Secure the guard onto the base with the screws provided.

Notch

Guard

Screw

Hot Supply

Base

Plug

Cold Supply

1443289-2-A 8 Kohler Co.

5. Install the Finished Floor

Finish the floor leaving a 3-1/2″(89 mm) by 2-1/2″(64 mm) hole

for the guard.

Cut the guard so it is flush with the finished flooring.

Guard

Finished Floor

3-1/2" (89 mm)

2-1/2"

(64 mm)

Fit the finished floor

between the

Min and Max lines.

Kohler Co. 9 1443289-2-A

6. Install the Faucet

NOTICE: To avoid damage to the O-rings on the bottom of the

faucet, keep the faucet vertical and use care when installing the

faucet.

Make sure the water is turned off.

Relieve the water pressure.

Remove the plugs from the base.

Remove the rubber protector (not shown) from the faucet.

Place the faucet onto the base and insert the screws and washers

provided through the flange.

Tighten the screws using the hex wrench provided.

Slide the escutcheon down onto the floor, covering the base.

Escutcheon

Screw

Washer

Flange

Base

Plug

Hex

Wrench

1443289-2-A 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-2419 Montageanleitung

Kohler

Kohler 10373 Bedienungsanleitung

Kohler

Kohler MINIMA K-45805T Bedienungsanleitung

Kohler

Kohler 4179A-NA Bedienungsanleitung

Kohler

Kohler ALEO Bedienungsanleitung

Kohler

Kohler K-7179 Montageanleitung

Kohler

Kohler K-8549 Bedienungsanleitung

Kohler

Kohler K-10349 Montageanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler SAN RAPHAEL PRESSURE LITE K-3394 Bedienungsanleitung

Kohler

Kohler Purist K-T14428 Bedienungsanleitung

Kohler

Kohler Mira Sport Thermostatic Bedienungsanleitung

Kohler

Kohler rada Bedienungsanleitung

Kohler

Kohler Iron Works K-2822 Bedienungsanleitung

Kohler

Kohler Cachet Quiet-Close K-7671 Bedienungsanleitung

Kohler

Kohler BEAM K-30939T Bedienungsanleitung

Kohler

Kohler Devonshire 193-4-2BZ Bedienungsanleitung

Kohler

Kohler K-T45115 Montageanleitung

Kohler

Kohler EX28093K-8 Bedienungsanleitung

Kohler

Kohler K-877 Kurzanleitung

Kohler

Kohler ENGLEFIELD Montageanleitung

Kohler

Kohler JULY Series Bedienungsanleitung

Kohler

Kohler K-2529 Montageanleitung

Kohler

Kohler K-10088 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung