Kohler Mira Evoco Series Bedienungsanleitung

11478624-W2-A

Mira Evoco

For SPARES,

ADVICE or REPAIRS

please call us free

on 0800 001 4040

(UK only)

These instructions must be left with the user

Affix Sticker Here

Model Name:

Product Code:

Date of Manufacture:

Installation and User Guide

(Please keep these details safe as you will need them when registering your

product guarantee. Your guarantee information is included in this guide.)

Evoco Dual

Evoco Triple

1478624-W2-A

PLEASE observe the following To reduce the risk of injury:

Installing the Shower

1. Installation of the shower must be carried out in accordance with

these instructions by qualied, competent personnel. Read all

instructions before installing the shower.

2. DO NOT install the shower where it may be exposed to freezing

conditions. Ensure that any pipework that could become frozen

is properly insulated.

3. DO NOT perform any unspecied modications to the shower

or its accessories. When servicing only use genuine Kohler Mira

replacement parts.

4. If the shower is dismantled during installation or servicing then,

upon completion, an inspection must be made to ensure all

connections are tight and that there are no leaks.

Using the Shower

5. The shower must be operated and maintained in accordance with

the requirements of this guide. Make sure you fully understand

how to operate the shower before use, read all instructions and

retain this guide for future reference.

6. DO NOT switch the shower on if there is a possibility that the water

in the shower unit or ttings is frozen.

Safety Information

WARNING ! This shower can deliver scalding temperatures. For

continued safe operation, follow all instructions, warnings and

cautions contained in this guide and on or inside the shower.

Periodic maintenance may be required to keep the product in

good working order.

The function of a thermostatic mixing valve is to deliver water

consistently at a safe temperature. In keeping with every other

mechanism, it cannot be considered as functionally infallible and

as such, cannot totally replace a supervisor’s vigilance where that

is necessary. Provided it is installed, commissioned, operated

and maintained within manufacturers recommendations, the

risk of failure, if not eliminated, is reduced to the minimum

achievable.

31478624-W2-A

7. Children younger than 3 years should not use this shower. Children

3 years to under 8 years should only use this shower under

continuous supervision. Children aged 8 years and above and

persons with reduced physical, sensory or mental capabilities or

lack of experience or knowledge can use the shower if they are

given supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved.

8. Anyone who may have di󰀩culty understanding or operating the

controls of any shower should be attended whilst showering.

Particular consideration should be given to the young, the elderly,

the inrm or anyone inexperienced in the correct operation of the

controls.

9. DO NOT allow children to clean or perform any user maintenance

to the shower unit without supervision.

10. Always check the water temperature is safe before entering the

shower.

11. DO NOT adjust the temperature control rapidly while using the

shower.

12. Use caution when altering the water temperature while in use,

always check the temperature before continuing to shower.

13. DO NOT switch the shower o󰀨 and back on while standing in the

water ow.

14. DO NOT t any form of outlet ow control. Only Mira recommended

outlet ttings should be used.

15. The showerhead must be descaled regularly. Any blockage of the

showerhead or hose may a󰀨ect showering performance.

16. The water supplies to this product must be isolated if the product is

not to be used for a long period of time. If the product or pipework

is at risk of freezing during this period they should also be drained

of water.

17. When this product has reached the end of its serviceable life, it

should be disposed of in a safe manner, in accordance with current

local authority recycling, or waste disposal policy.

18. This appliance is intended to be permanently connected to the

water supply and not connected using a exible hose set.

1478624-W2-A

Introduction

Thank you for choosing a Mira shower. To enjoy the full potential of your new shower, please

take time to read this guide thoroughly, and keep it handy for future reference. Products

manufactured by Kohler Mira Ltd are designed to be safe, provided that they are installed,

used and maintained in good working order, in accordance with our instructions and

recommendations.

Follow all warnings, cautions and instructions contained in this guide, and on, or inside

the shower. This guide is also available in digital format from our website or by contacting

customer services.

Type 2 Valves

This product has been certied as a Type 2 valve. It also complies with the Water Supply

(water ttings) regulations 1999. For further information on Type 2 Valves, refer to the TMV2

Requirements Manual (available to view or download on our website www.mirashowers.com).

The approved designation for this product is listed in the table below.

Product Code Model Name Colour Type 2 Designation

B12A Dual Outlet Shower

Chrome, Matt

Black & Brushed

Nickel

HP-S

B12AL LIT Dual Outlet Shower

B12B Dual Outlet Bathll

B12BL LIT Dual Outlet Bathll

B12CL LIT Triple Outlet Bathll

Guarantee

For domestic installations, Mira Showers guarantee the product against any defect in

materials or workmanship for a period of ve years from the date of purchase (shower ttings

for one year).

For non-domestic installations, Mira Showers guarantee the product against any defect in

materials or workmanship for a period of one year from the date of purchase.

Failure to follow the instructions provided with the shower will invalidate the guarantee.

For Terms and Conditions refer to the 'Activating Your Free Guarantee and Customer

Service' pages.

Design Registration: 007749684-0005, 007749684-0006, 007749684-0007,

007749684-0008, 007749684-0009

Design Registration and Patents

Domestic Light Commercial 

Heavy Commercial Healthcare 

Recommended Usage

51478624-W2-A

Mira PBBI Evoco

For SPARES,

ADVICE or REPAIRS

please call us free

on 0800 001 4040

(UK only)

These instructions must be left with the user

Affix Sticker Here

Model Name:

Product Code:

Date of Manufacture:

Installation and User Guide

(Please keep these details safe as you will need them when registering your

product guarantee.Your guarantee information is included in this guide.)

1478524-W2-A

Evoco Dual

Evoco Triple

Pack Contents

X1 qX1 q

X1 q

X3 q

X1 q

X2 q

X4 qX3 q

X3 q

X1 qX2 qX1 q

X1 q

X4 qX4 q

X1 q

X2 q

X6 q

Important! Some parts may di󰀨er from the below depending on product purchased.

X1 q

1478624-W2-A

X1 q

Additional Items Required (Not Supplied)

X1 q

Waterproof Tanking Adhesive

(see ‘Installation - General’

for details) q

Push Fit Stop End

(suitable for 15mm

copper pipe) q

Silicone Sealant q

X1 q

Important! Some parts may di󰀨er from the below depending on product purchased.

71478624-W2-A

• For safety and comfort the thermostat will shut o󰀨 the mixing valve within

2 Seconds if either supply fails (achieved only if the blend temperature has

a minimum di󰀨erential of 12°C from either supply temperature).

• Important! This product uses 15mm Push t connectors and is not suitable

for any other pipe sizes. We recommend the use of copper pipework.

• Warning! This product does not allow for reversed inlets and will deliver

dangerously unstable temperatures if tted incorrectly.

Thermostatic Shut-down

Specications

Pressures

Maximum Static Pressure 1000 kPa (10 bar)

Maximum Maintained Pressure 500 kPa (5 bar)

Minimum Maintained Pressure

(Gas Water Heater)

100 kPa (1 bar)

(for optimum performance supplies should be

nominally equal)

Minimum Maintained Pressure

(Gravity System)

10 kPa (0.1 bar),

(0.1 bar = 1 Metre head from cold tank base to shower

handset outlet)

Temperatures

Close temperature control 20°C - 50°C

Optimum Thermostatic Control

Range

35°C to 45°C

(achieved with supplies of 15°C cold, 65°C hot and

nominally equal pressures)

Recommended Hot Supply 60°C to 65°C

Minimum Hot Water Supply Tem-

perature

55°C (Note: The mixing valve can operate

at temperatures up to 85°C for short periods

without damage. However for safety reasons it

is recommended that the maximum hot water

temperature is limited to 65°C). Warm up feature

may not work if your hot inlet temp is below 55°C.

Minimum Recommended

Di󰀨erential between Hot Supply

and Outlet Temperature

12°C at desired ow rates

Cold Water Range 1 - 25°C

Plumbing Connections

Hot: Left 15mm Push Fit

Cold: Right 15mm Push Fit

Outlet: Dual/Triple Outlet = RAC: 15mm Push Fit

Overhead and Bathller: 15mm Push Fit

1478624-W2-A

Warning! This product does not allow for reversed inlets and will deliver

unstable temperatures if tted incorrectly.

Installation

General

1. Installation of the shower must be carried out in accordance with these

instructions by qualied, competent personnel.

2. The plumbing installation must comply with all national or local water regulations

and all relevant building regulations, or any particular regulation or practice

specied by the local water supply company.

3. Make sure all pressures and temperatures comply with the requirements of the

shower. See ‘Specications’. For Type 2 Valves, refer to supply conditions

given in the TMV2 Requirements Manual (this is available to view or

download from our website www.mirashowers.com).

4. Full bore/non restrictive servicing valves must be tted in a readily accessible

position adjacent to the shower to facilitate maintenance of the shower.

DO NOT use a valve with a loose washer plate (jumper) as this can lead to a

build up of static pressure.

5. The product contains built in check valves. DO NOT install inlet check valves

as this can lead to a build up of static pressure and potential product damage

and leaking.

6. DO NOT apply excessive force to plumbing connections; always provide

mechanical support when making plumbing connections. Any soldered joints

should be made before connecting the shower.

7. Pipework dead-legs should be kept to a minimum.

8. DO NOT install the shower unit in a position where access for maintenance is

restricted.

9. The shower must be tted to a waterproof, at and even wall surface.

Decorative and mosaic tiles are not recommended in the area where the shower

is to be installed, as they may cause problems with sealing around the valve

and also e󰀨ect product operation.

10. The wall cavity must provide su󰀩cient support for the shower unit. The 4 cavity

xing screws (No. 10 x 2”) and wall plugs supplied are suitable for most solid

wall and stud partition installations. Use all 4 xing points to secure the shower

unit, be sure to use xings appropriate for the chosen wall structure. The front

concealing plate must be tted to a waterproof, at and even wall surface.

Suitable Plumbing Installations

The Thermostatic Mixer can be installed with all systems with balanced pressures.

Mixed gravity and mains supplies are not recommended.

91478624-W2-A

11. Position the shower unit where the controls are at a convenient height for the

user. Position the showerhead so that the water sprays in line with the bath or

across the opening of a shower cubicle. The installation must not cause the

shower hose to be kinked during normal use.

12. A suitable waterproof shower tanking adhesive is required for the fabric wall

seal supplied. We recommend a liquid based plumbing type to be applied with

a paint brush, available from tile / builder merchants. A su󰀩cient amount is

required for coating the fabric seal twice during the installation.

13. The water supplies to this product should be isolated if the product is not to be

used for a long period of time. If the product or pipework is at risk of freezing

during this period they should also be drained of water.

14. The position of the shower and shower ttings must provide a minimum air

gap of 25 mm between the showerhead and the spill over level of any bath,

shower tray or basin. There must be a minimum distance of 30 mm between

the showerhead and the spill over lever of any toilet, bidet or other appliance

with a Fluid Category 5 backow risk.

Zone of

Backflow

Risk

30 mm

Minimum

oilet or Bidet

FC5

Hand Basin

FC3

Bath or Shower

Tray FC3

Shower

Unit

25 mm

Minimum

25 mm Minimum

Note : There will be occasions when the hose retaining ring will not provide

a suitable solution for Fluid Category 3 installations. In these instances an

outlet double checkvalve must be tted, this will increase the required

supply pressure typically by 10 kPa (0.1 bar). Double checkvalves tted in

the inlet supply to the appliance cause a pressure build up, which a󰀨ects

the maximum static inlet pressure for the appliance and must not be tted.

For Fluid Category 5, double checkvalves are not suitable.

1478624-W2-A

Determine the pipework route. All pipework to the product must be clipped and

supported to prevent movement and pipe noise due to any pulse pressures.

Position the outlet so that the shower hose will not obstruct the control handle and

the xing screws will avoid the outlet pipe.

Decide on a suitable position for the shower unit and ttings.

Installation

Warning! Isolate the water supplies before installing the shower.

Warning! This product does not allow for reversed inlets and will deliver

dangerously unstable temperatures if tted incorrectly.

Evoco Triple Evoco Dual

Shower

Fittings

Water Inlets

Overhead

Bath

Filler

HOT COLD

Outlet

Pipe

Water Inlets

HOT COLD

Shower

Fittings

Overhead

Bath

Filler

Outlet

Pipe

Building In

Box

Building In

Box

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-T16225 Montageanleitung

Kohler

Kohler K-6558 Bedienungsanleitung

Kohler

Kohler K-2032-0 Bedienungsanleitung

Kohler

Kohler K-T10581 Montageanleitung

Kohler

Kohler K-1630-L Bedienungsanleitung

Kohler

Kohler K-45471X Montageanleitung

Kohler

Kohler K-T13140 Bedienungsanleitung

Kohler

Kohler K-24804-4N-CP Bedienungsanleitung

Kohler

Kohler K-T944 Bedienungsanleitung

Kohler

Kohler Sterling SC2522SBG Montageanleitung

Kohler

Kohler K-3607 Montageanleitung

Kohler

Kohler 24811A-0 Installationsanleitung

Kohler

Kohler K-557-K Bedienungsanleitung

Kohler

Kohler K-812-H2 Montageanleitung

Kohler

Kohler 72419IN Bedienungsanleitung

Kohler

Kohler K-1243 Bedienungsanleitung

Kohler

Kohler K-193-4-CP Bedienungsanleitung

Kohler

Kohler K-10430 Bedienungsanleitung

Kohler

Kohler K-14402 Montageanleitung

Kohler

Kohler K-6813 Montageanleitung

Kohler

Kohler K-6490 Bedienungsanleitung

Kohler

Kohler Stillness 979T-4 Bedienungsanleitung

Kohler

Kohler K-1110 Kurzanleitung

Kohler

Kohler ODEON K-8711T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung