Kohler ODEON K-8711T Bedienungsanleitung

BEFORE YOU BEGIN

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation . This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time withoutnotice.

These instructions contain important care, cleaning, and

warranty information-please leave instructions for the

consumer.

ORDERING INFORMATION

Odeon P-trap 180mm Toilet K-8711T

Includes seat K-8741T-*

Includes Bowl K-8709T

Includes Tank K-8710T

Odeon S-trap 255mm Toilet K-8753T

Includes seat K-8741T-*

Includes Bowl K-11184T

Includes Tank K-8710T

Odeon S-trap 305mm Toilet K-8766T

Includes seat K-8741T-*

Includes Bowl K-8767T

Includes Tank K-8710T

Service parts

Fill valve K-82984-B

Mounting Plate Assy K-1004142

Flush Valve Assy K-1004139

NOTES

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 155mm (6-1/8") centers.

Passageways is 60mm (2-3/8").

Water depth from rim is 245mm (9-5/8")

Ensure that the new drain and shut-off valve have the

correct roughing-in dimensions. .

Be very careful while working with vitreous china products.

Vitreous china can break or chip if the bolts or nuts are

overtightened, or if carelessly handled.

Carefully inspect the new fixture for any sign of damage.

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112. 19.2M).

See Fig.#1

180mm K-8711T

K-8741T-*

K-8709T

K-8710T

255mm K-8753T

K-8741T-*

K-11184T

K-8710T

305mm K-8766T

K-8741T-*

K-8767T

K-8710T

K-82984-B

K-1004142

K-1004139

155mm(6-1/8")

60mm(2-3/8")

245mm(9-5/8")

ASME(A112. 19.2M)

-1-

INSTALLATION INSTRUCTIONS

P/S-

VITREOUS CHINA P/S-TRAP TOILET

P-TRAP 180mm K-8711T S-TRAP 255mm K-8753T

S-TRAP 305mm K-8766T

1037406-T01-A

ODEON

, 2004

528137

1. REMOVE EXISTING TOILET

Turn off water supply. flush the toilet and use a sponge to

remove the remaining water from the tank and bowl.

Disconnect the supply shut-off valve (if present) and remove

the old tank and bowl.

()

TOOLS AND MATERIALS REQUIRED

(Not supplied)

254mm adjustable wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Straight pipe coupling

Connection packing

Toilet supply shut-off valve, 10mm (3/8") recommended

The fill valve

nut has been factory-tightened, wrench tighten 1/4 turn

past finger tight.

If no shut-off valve exists, install a shut-off valve

below the tank before installing the new toilet.

Flexible hose are recommended to connect the supply line to

the fill valve. If you use a rigid connection, take care not to

apply side forces to the bottom of the fill valve.

WARNING: Risk of external leakage.

NOTICE:

()

254mm

10mm(3/8")

1/4

ROUGHING-IN

-2-

698

337

267

362

166

158

429

390

204

777 10

388

396

178

159

102

P-trap 8711T

204

776 10

392

474

305 102

S-trap

8753T

204

785 10

394

484

255 100

S-trap

8766T

Fig.#1

699

337

265362

158

156

428

390

INSTALLATION

736

344

259

363

162

155

433

390

1037406-T01-A

Unit:mm

-3-

3. SELECT P-TRAP OR S-TRAP

to installation

your toilet according to the drain and shut-off valve's

Roughing-in dimensions.

2. ASSEMBLE TANK BOLTS&WASHERS

Slip bolt heads into mounting plate on bottom of tank. Place

large foam washer on base of flush valve.

Place tank on bowl and attach with nuts and washers from

under bowl.

See Fig. #2a.

See Fig.#2b.

NOTE:

Do not use white cement or high lime content

cements to install this toilet. The expansion of cement due to

a rise in temperature may make the toilet crack or cause

damage. Kohler is not responsible for any damage caused by

installation with the use of cement.

Fig.#2a

Fig.#3a

Fig.#3b

S-trap installation P-trap installation

Fig.#2b

100

120

180

255/305

100

120

180

1037406-T01-A

-4-

4 Connect fill valve to water supply with hose only. 4

4. INSTALL THE TOILET & CONNECT WATER SUPPLY

Place the toilet in its final location. Use plastic drill guide and

8mm drill bit to drill floor mounting holes for installation over

concrete. Use 4mm to 4.5mm drill for wood floor installation.

See Fig.#4a

Install anchors and caps.

WARNING:

Do not overtighten floor bolts, as damage

to the vitreous can occur.

8mm

4-4.5mm

NOTE: use hose only, length:

200-300mm mini.

(Not provided.)

200-300mm

()

Fig. #4a

NOTE: Do not use white cement or high lime content

cements to install this toilet. The expansion of cement due to

a rise in temperature may make the toilet crack or cause

damage. Kohler is not responsible for any damage caused by

installation with the use of cement.

1037406-T01-A

5.CHECK WATER LEVEL

Turn on water supply check for leaks. If necessary, adjust

black float adjustment clip, and sliding float up or down on

metal float rod until water level at marked water line .5A

6. ADJUST OVERFLOW HEIGHT (If necessary)

Adjust overflow tube so that the top is 20mm above the

waterline. Push locking mechanism to the side and adjust

tube height. Push locking mechanism back into position to

lock tube height. See Fig.#6.

Make sure the arrow on the green float on the white flush

valve is secure and pointing to #2. (Fig. 5B )

6. ( )

20mm

(5B)

Fig. #6

Fig. #5

-5-

1maxi 2

Float

Adjustment clip

190

1037406-T01-A

-6-

7. CONNECT PUSH BUTTON

Put large flange through hole in lid. Screw retaining ring onto

flange. Turn the screw inside the push button flange to secure

tank lid to flush valve assembly. Make certain that the flush

valve assembly is adjusted high enough that the button

touches the assembly. Put green and white push

rods into corresponding holes and trim flush with the top of

the flange. Install flush buttons.

See 6 .

See Fig. 7 . See Fig. 8 .

Fig. #7

341&1 1/2 tour

1037406-T01-A

-7-

8. Install seat with hardware provided.

See Fig.#8.

8. 8

Fig. #8

1037406-T01-A

SYMPTOMS PROBABLE CAUSES CORRECTIVE ACTION

TROUBLESHOOTING CHART

1. Float valve turns on/off

by itself without toilet

being flushed

2. Float valve continues

to run, allowing water

to enter tank.

3. Incorrect water level

height.

4. Long or noisy tank fill

5. Poor flush.

6. Toilet overflows.

A. Flush valve seal worn, dirty or damaged.

A. Float height incorrect.

A. Plugged valve inlet or supply line.

A. Water usage is too low.

B. Trapway obstructed.

C. Soil pipe or vent is obstructed.

D. Supply shut-off valve not fully open.

A. Toilet trapway is obstructed.

B. Soil pipe or vent is obstructed.

A. Inspect, clean and, if necessary replace seal.

A. Adjust float by squeezing float adjustment clip,

and sliding float up or down on float rod until

water leve is at marked water line.

A. Perform corrective action 2.A.

A. Adjust the water tank level.

B. Unclog trapway.

C. Clear obstruction from soil pipe or vent.

D. Open supply shut-off valve.

A. Use plunger to unclog.

B. Clear obstruction from soil pipe or vent pipe.

A. Foreign particles lodged under the float valve

seal (located under float valve cap)

B. Float valve seal (located under float valve cap)

may be cracked or split.

C. Tank water level set above overflow level.

A. Shut off water supply; remove float valve cap

assembly by rotating 1/8 turn

counterclockwise. Cover uncapped lower

valve unit with an inverted cup (holding it to

prevent overspray), and turn water on and off

a few times. Clean float valve seal surface

(located under float valve cap). Replace float

valve cap assembly by engaging lugs and

rotating 1/8 turn clockwise. Turn water on.

Install filter in supply line to prevent recurring

problems.

C. During fill cycle, hold float under water a few

seconds to allow it to fill with water ballast.

Adjust float by squeezing float adjustment clip,

and sliding float up or down on float rod until

water level is at marked water line.

B. Replace seal.

A. (

)

B. ( )

1/8

()

1/8

3. A.

4. A. 2AA.

5. A.

6. A.

-8-

1037406-T01-A

()

138

200021

Plumbing Fixtures and Fittings Limited

One-year Warranty

Kohler plumbing fixtures and fittings are warranted to be free

of manufacturing defects.

This product is warranted for one year from date of purchase.

Kohler China will be responsible for any problems caused by

manufacturing defects provided with the invoice. Kohler

China will, at its election, repair, replace or make appropriate

adjustment where Kohler China inspection discloses any

such defects occurring in normal usage within one year after

purchase.

Implied warranties including that of merchantability and

fitness for a particular purpose are expressly limited in

duration to the duration of this warranty, Kohler China

disclaims any liability for special, incidental or consequential

damages. Damages to the product caused by misuse, abuse

and installation that is not in accordance with the owner's

manual are not covered by this warranty.

To obtain quick warranty service, please contact your dealer,

or write to Kohler China. (Original sales receipt must be

provided as the proof of purchase.)

Kohler China Investment Company Ltd.

Central Customer Service Center

19/F, Shanghai Square, 138 Huai Hai Road,

Luwan District, Shanghai, PRC

Zip Code: 200021

This is our exclusive written warranty.

LIMITED ONE-YEAR WARRANTY

-9-

CONSUMER RESPONSIBILITIES

If you live in a hard water area, make certain that the holes in

the toilet rim are kept clean to ensure proper bowl flushing.

Toilet bowl cleaners should be used at least once a week.

Use a long-handled brush to clean the rim holes, and to clean

as far into the trap as possible to prevent mineral deposits

from forming.

Most toilet bowl cleaners are not harmful to the vitreous china

surface of the toilet bowl. Please follow the bowl cleaner

manufacturers instructions carefully.

Do not use abrasive cleaners or solvents.

Do not use in-tank cleaners. Products containing

chlorine (calcium hypochlorite) can seriously damage

fittings in the tank. This damage can cause leakage

and property damage.

Kohler Company shall not be responsible or liable for any

damage to these tank fittings caused by the use of cleaners

containing chlorine (calcium hypochlorite).

WARNING: Risk of property or product damage.

1037406-T01-A

ODEON

1004136-**

Tank Cover

K-8741T-**

Odeon Seat

1021449

Screw

1021447

Right Hand

Hinge

1021446

Left Hand Hinge

1004139

Flush Valve Assy.

1004140

Flush Button Assy.

1021422

Green Flush

Stick

1021423

Black Flush

Stick

1021426

Overflow Tube

Fixture

53154

Gasket

1007746

Nut

1021448

Hardware

Assembly

1021425

Flush Button

Support

82984-B

Float Valve

Assy.

83143

Seal

G1/2 Shank

84929

Washer

1021421

Flush

Valve

Body

1021424

Flapper

84897

Locknut

1000687

Tank/Plate

Gasket

1004142

Mounting

Plate & Bolts

1004141

Floor

Mounting Kit

1032265

Gasket

** Color code must be specified when ordering.

Model

Tank

Seat

K-8711T K-8753T K-8766T

K-8710T K-8710T K-8710T

K-8741T-** K-8741T-** K-8741T-**

Bowl K-8709T K-11184T K-8767T

SERVICE PARTS PAGE

P/S-

VITREOUS CHINA P/S-TRAP TOILET

P-TRAP 180mm K-8711T S-TRAP 255mm K-8753T

S-TRAP 305mm K-8766T

-10-

1037406-T01-A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-307 Montageanleitung

Kohler

Kohler Rada Tripoint-F 2.1658.011 Bedienungsanleitung

Kohler

Kohler K-13132 Bedienungsanleitung

Kohler

Kohler Digital Interface K-683 Bedienungsanleitung

Kohler

Kohler Rapport K-1496-H2 Bedienungsanleitung

Kohler

Kohler STERLING 5300 Series Montageanleitung

Kohler

Kohler K-9132 Bedienungsanleitung

Kohler

Kohler K-3524 Montageanleitung

Kohler

Kohler K-T461 Bedienungsanleitung

Kohler

Kohler 10089W-CP Bedienungsanleitung

Kohler

Kohler Antique K-100 Montageanleitung

Kohler

Kohler ALEO S 31240T-4 Bedienungsanleitung

Kohler

Kohler K-20099T-Y Bedienungsanleitung

Kohler

Kohler K-6817 Montageanleitung

Kohler

Kohler JULY 16316M-4 Bedienungsanleitung

Kohler

Kohler K-5414 Betriebsanleitung

Kohler

Kohler Flipside 17492T Bedienungsanleitung

Kohler

Kohler K-2419 Montageanleitung

Kohler

Kohler Mira Escape Thermostatic 9.0 kW J95Hb/c Bedienungsanleitung

Kohler

Kohler Sunstruck K-1967-GHW Bedienungsanleitung

Kohler

Kohler K-4177 Bedienungsanleitung

Kohler

Kohler K-332 Bedienungsanleitung

Kohler

Kohler STEWARD ECO Bedienungsanleitung

Kohler

Kohler K-19909-4 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung