Kohler GABRIELLE CLASS FIVE S-EB K-3322T-W Bedienungsanleitung

GABRIELLE CLASS FIVE

INSTALLATION INSTRUCTIONS

VITREOUS CHINA SIPHON JET TOILET

S-EB K-3322T-W/K-3322T-SW/K-3322T-CW

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

·-

ORDERING INFORMATION

GABRIELLE CLASS FIVE Toilet K-3322T-W

Includes French Curve Toilet Seat K-4653T

GABRIELLE CLASS FIVE Toilet K-3322T-SW

Includes CACHET Quiet-Close Toilet Seat K-4636T-U

GABRIELLE CLASS FIVE Toilet K-3322T-CW

Includes French Curve Quiet-Close Toilet Seat K-4713T

NOTES

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 140mm (5-1/2") centers.

51mm (2") passageway.

Water depth from the rim is 127mm (6-5/8").

Ensure that the new drain has the correct roughing-in

dimension. This toilet has a 305mm (12") roughing-in

dimension. .

Closet flange must be 305mm (12") on-center from wall.

Carefully inspect the new fixture for any sign of damage.

For new construction, refer to the dimensions in

for locating the shut-off valve.

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112.19.2-2008).

See Fig. #1

Fig. #1

and Fig. #4

140mm

51mm

127mm

305mm

ASME A112.19.2-

2008.

K-3322T-W

K-4653T

K-3322T-SW

K-4636T-U

K-3322T-CW

K-4713T

, 2011

528137

-1-

1176009-T01-A

-2-

TOOLS AND MATERIALS REQUIRED

(Not supplied)

254mm (10") adjustable wrench

305mm (12") pipe wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Toilet gasket (wax seal)

Toilet installation flange

Toilet T-bolts (2), 8mm (5/16") diameter with nuts &

washers

Toilet supply shut-off valve

If the existing toilet does not have a supply shut-off

valve below the tank, install one before installing the new

toilet.

NOTICE:

()

254mm

305mm

()

8mm T (2 )

127

10mmN.P.S. SUPPLY 130

FRONT OF BOWL

390

259

248

Fig.#1

Unit: mm

Reference Value

Kohler reserves the right to change marked dimensions without prior notice.

WARNING: Risk of personal injury or product

damage.

WARNING: Risk of external leakage

Handle vitreous china products very carefully.

Vitreous china can break and chip if you over tighten

bolts and nuts.

. The fill valve

nut has been factory-tightened to design specifications.

If re-tightening is required, wrench tighten 1/4 turn past

finger tight .

1/4

681

479

718

390

FINISHED WALL

OF OUTLET

305

1176009-T01-A

Remove the old gasket from the floor

and the closet flange with a putty knife.

Remove the old T-bolts and discard

them.

f the new toilet is not

installed immediately, temporarily stuff

a rag into the closet flange.

NOTICE: I

Fig.#2

Closet Flange

TO REMOVE EXISTING TOILET

Turn off the water supply. Flush the toilet, and use a sponge

to remove the remaining water from the tank and bowl.

Disconnect the supply shut-off valve (if present), and remove

the old tank and bowl.

()

INSTALLATION

TO INSTALL SUPPLY

SHUT-OFF VALVE

Install the supply shut-off valve so it

is127mm above the finished floor line,

and 130mm to the left of the closet

flange centerline.

The centerline of the supply shut-off

valve outlet should extend 70mm from

the finished wall. Install the supply

shut-off valve with the outlet vertical.

127mm

130mm

70mm

Fig.#4

Supply Shut-Off Valve

Closet Flange

Centerline

130

305

127

Install two new 8mm (5/16") diameter

T-bolts into the closet flange.

Do not use white cement or

high lime content cements to install

this toilet. The expansion of cement

due to a rise in temperature may make

the toilet crack or cause damage.

Kohler is not responsible for any

damage caused by installation with the

use of cement.

NOTICE:

8mm T

Fig.#3

Closet Flange

T-bolts

-3-

1176009-T01-A

TO INSTALL TOILET

Set the toilet upside down on some

padding. Firmly press the toilet gasket

onto the toilet outlet.

Wax ring type toilet gasket

should not be installed at temperatures

less than 21 .

if you are using a toilet

gasket with an integral plastic sleeve,

make sure the gasket is positioned

with the sleeve facing away from the

toilet.

If you temporarily plugged the closet

flange with a rag, remove the rag at

this time and ensure that the drain pipe

is clear and free of debris.

Carefully align and lower the toilet over

the closet flange and T-bolts. Apply full

body weight to the toilet rim to set the

seal.

Do not lift or rock the

toilet after placement-anew

toilet gasket must be installed if

you break the watertight seal.

NOTE 1:

NOTE 2:

CAUTION: Risk of concealed

leakage.

Fig.#5

Toilet Outlet (OUTLET)

Toilet Gasket

Fig.#6

Assemble the bolt cap bases, washer,

and nuts on the exposed T-bolts.

Handtighten the nuts, then tighten

them an additional 1/2-turn.

overtightening may cause

breakage or chipping of the

vitreous china.

If the T-bolts extend more than 6mm

(1/4") over the top of the nuts, cut off

the excess and file the end. Wipe

away any residue. Install the bolt caps.

CAUTION: Risk of personal

injury or product damage.

T 6mm

*Supplied with toilet

T-Bolt

Bolt Cap*

Nut

Washer

Bolt Cap Base*

Supply Shank*

Supply Shut-Off Valve

Fig.#7

*()

()

TO CONNECT WATER

SUPPLY

* Flexible hose (not provided) are

recommended to connect the supply

line to the fill valve. If you use a rigid

connection(not provided), take care

not to apply side forces to the bottom

of the fill valve. Be sure the rigid

connection must be fit with supply line

completely to prevent damage shank

by forced connection.

-4-

1176009-T01-A

Attach the toilet seat according to the

installation instructions included.

Open the supply shut-off valve and

check all connections for leakage. If

the connections have been properly

assembled, a slight retightening of the

nuts should stop any leakage.

FILL FLOAT WITH

BALLAST

Test flush the toilet.

Periodically Check all connections for

leaks for several days following

installation.

Set the tank cover in place on the tank.

Fig.#9

Fig.#8

Check

This Area

-5-

OPEN

MINOR ADJUSTMENT OF

WATER LEVEL

Move the snap along "OPEN" direction.

To lower water level: Move water cup

down to a proper height and rotate

screw anticlockwise to achieve the

desired water level. (Refer to float

adjustment instructions.)

Fig.#10a

10a

Fig.#10b

10b

Snap

SCALE

5:1

Screw

OPEN

1176009-T01-A

To elevate water level: Rotate screw

clockwise and raise float to the desired

water level. Elevate water cup to a

proper position as well. (Refer to float

adjustment instructions.)

Fig.#10c

10c

CLOSEFasten the snap along "CLOSE"

direction.

Fig.#10d

10d

SCALE

5:1

OPEN

E G 2-4mm

Float adjustment instructions: Make

sure the height of surface E is 2-4mm

lower than surface G.

Fig.#10e

10e

Screw

Float

Water Cup G

-6-

1176009-T01-A

7. Toilet does not activate. A. Chain is not connected to lift rod or

flush valve.

A. Reconnect the chain.

1. Float valve turns on/off by itself

without toilet being flushed.

A. No slack in flapper chain assembly,

holding flapper off seat.

B. Flush valve flapper ball worn, dirty

or misaligned with flush valve seat;

or seat corroded so flapper will not

seal.

C. Refill tube pushed too far down in

overflow pipe.

A. Adjust flapper chain assembly for

proper slack.

B. Inspect, clean and, if necessary,

replace flapper ball and/or seat.

C. Attach refill to overflow pipe above

the water line.

2. Float valve continues to run, allowing

water to enter tank.

A. Foreign particles lodged under the

float valve seal (located under float

valve cap)

B. Float valve seal (located under float

valve cap) may be cracked or split.

C. Tank water level set above overflow

level.

D. Water leaking past flush ball.

A. Shut off water supply; remove float

valve cap assembly by rotating 1/8

turn counterclockwise. Cover

uncapped lower valve unit with an

inverted cup (holding it to

overspray), and turn water on and off

a few times. Clean float valve seal

surface (located under float valve cap).

Replace float valve cap assembly by

engaging lugs and rotating 1/8 turn

clockwise. Turn water on.

Install filter in supply line to prevent

recurring problems.

B. Replace seal.

D. Replace flush ball.

E. Turn trip lever nut clockwise to loosen

until trip lever no longer binds

E. Trip lever binding, holding flush ball

open.

During fill cycle, hold float under water

a few seconds to allow it to fill with

water ballast. Refer to "Minor

Adjustment of Water Level" for

waterline adjustment.

prevern

3. Incorrect water level height. A. Valve float cup does not contain

enough water to provide required

ballast.

B. Float height incorrect.

A. During fill cycle, hold float under water

a few seconds to allow it to fill with

water ballast.

B. Refer to "Minor Adjustment of Water

Level" for waterline adjustment.

4. Long or noisy tank fill cycle. A. Plugged valve inlet or supply line. A. Perform Corrective Action 2.A.

5. Poor flush. A. Water level is too low.

B. Trapway or rim holes are obstructed.

C. Soil pipe or vent is obstructed.

D. Supply shut-off valve not fully open.

E. Low water level in bowl due to refill

tube being plugged or out of overflow

tube.

A. Adjust water level.

B. Unclog trapway; clean rim holes.

C. Clear obstruction from soil pipe or

vent.

D. Open supply shut-off valve.

E. Clean or straighten refill tube attach

refill tube to overflow tube.

tank

6. Toilet overflows. A. Toilet trapway is obstructed.

B. Soil pipe or vent is obstructed.

A. Use plunger to unclog.

B. Clear obstruction from soil pipe or

vent pipe.

-7-

1176009-T01-A

-8-

3. A.

6. A.

7. A. A.

5. A.

2. A. (

)

B. ( )

1/8

()

(

) 1/8

4. A. A. 2A

1176009-T01-A

CONSUMER RESPONSIBILITIES

If you live in a hard water area, make certain that the holes in

the toilet rim are kept clean to ensure proper bowl flushing.

Toilet bowl cleaners should be used at least once a week.

Use a long-handled brush to clean the rim holes, and to clean

as far into the trap as possible to prevent mineral deposits

from forming.

Some toilet cleaner will damage chrome surface or faucet

settings. Please use with care avoid contact with chrome

surface.

Do not use abrasive cleaners or solvents.

Do not use in-tank cleaners. Products containing

chlorine (calcium hypochlorite) can seriously damage

fittings in the tank. This damage can cause leakage

and property damage.

Kohler Company shall not be responsible or liable for any

damage to these tank fittings caused by the use of cleaners

containing chlorine (calcium hypochlorite).

WARNING: Risk of property or product damage.

Please do not use hard materials (like

scouring pad) to clean product surface, especially the

product logo.

CAUTION:

CAUTION: Don t use any cement while installing

the toilet.

WARNING: Risk of product damage.

Heat expansion of the toilet may damage

the feet of the toilet. Kohler will not be responsible for

any damage because of using cement.

Do not throw into the toilet what is easy to block it,

such as newspaper, paper pilch, sanitary towel.

Do not bump the vitreous china with great force to

prevent it from damaging and leaking.

Do not use the product in the water below 0 C.

( )()

()

-9-

1176009-T01-A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Toilette Handbücher

Kohler

Kohler K-11451 Montageanleitung

Kohler

Kohler Novita BD-N450US Montageanleitung

Kohler

Kohler WELLCOMME K-4349T Bedienungsanleitung

Kohler

Kohler REACH K-3834T-2 Bedienungsanleitung

Kohler

Kohler K-22106T-2 Bedienungsanleitung

Kohler

Kohler K-3900X Montageanleitung

Kohler

Kohler K-5401-PA Montageanleitung

Kohler

Kohler FLEUR WATERGUARD K-3417 AA Series Bedienungsanleitung

Kohler

Kohler K-4917 Montageanleitung

Kohler

Kohler K-5724K Bedienungsanleitung

Kohler

Kohler SAN MARTINE K-5503T-TFC1 Bedienungsanleitung

Kohler

Kohler K-3451 Montageanleitung

Kohler

Kohler K-6419 Bedienungsanleitung

Kohler

Kohler STERLING 402024 Montageanleitung

Kohler

Kohler K-5401TW-2-0 Bedienungsanleitung

Kohler

Kohler K-4026 Montageanleitung

Kohler

Kohler K-11489X Montageanleitung

Kohler

Kohler REVE K-24766T-S Bedienungsanleitung

Kohler

Kohler K-3575 Montageanleitung

Kohler

Kohler VEIL K-5402A-0 Bedienungsanleitung

Kohler

Kohler K-2590 Bedienungsanleitung

Kohler

Kohler K-6191X Montageanleitung

Kohler

Kohler Veil Comfort Height Montageanleitung

Kohler

Kohler K-11452 Montageanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung