Kohler K-3399 Bedienungsanleitung

Installation Guide

One-Piece Toilet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-3399

1021800-2-B

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

CAUTION: Risk of personal injury or product damage. Handle

with care. Vitreous china can break or chip if the product is

handled carelessly.

DANGER: Risk of electrical shock. Connect to a properly

grounded, grounding-type receptacle, protected by a

Ground-Fault Circuit-Interrupter (GFCI).

A dedicated 120 VAC, 15 A, 60 Hz circuit (protected by a Class A

GFCI) is required for installation.

NOTICE: The Canadian Electric Code requires receptacles installed

in bathrooms to be located at least 1 meter from a bathtub or

shower if practical, but in no case less than 500 mm. If the

installation is in Canada, install this unit in accordance with the

Canadian Electrical Code, Part 1.

Observe all local plumbing and building codes.

CAUTION: Risk of product or property damage. Do not use

rigid conduit to install this toilet. Rigid conduit may put

excessive stress on the toilet, which can cause damage to the

toilet tank or the installation site.

10" Adjustable

Wrench Supply

Shut-Off

Valve

Tape

Measure

Tubing Cutter Safety

Glasses

Plus:

• 5/16" T-Bolts w/ Nuts and Washers

• Putty Knife

• Screwdriver

• Electrical Tools and Supplies

• Hacksaw

• Level

• Sponge

• Pipe Wrench

• Metal File

• Liquid-Tight Conduit

Wax Seal

1021800-2-B 2 Kohler Co.

Before You Begin (cont.)

NOTICE: If local codes will not permit you to use a liquid-tight,

ﬂexible conduit, do not attempt to install this toilet.

Carefully inspect the new toilet for damage.

If the existing toilet does not have a supply shut-off valve below

the tank, install one before installing the new toilet.

Kohler Co. 3 1021800-2-B

1. Remove the Existing Toilet

Turn off the water supply.

Flush the toilet, then sponge out all remaining water from the

tank.

Disconnect the supply shut-off valve (if present), and remove the

old tank and bowl.

Remove the old wax seal from the ﬂoor with a putty knife.

Replace the old T-bolts with the new 5/16″diameter T-bolts.

CAUTION: Risk of hazardous gases. If the new toilet is not

installed immediately, temporarily stuff a rag in the closet ﬂange.

T-Bolt

Scrape off the old

wax seal

Closet

Flange

1021800-2-B 4 Kohler Co.

2. Install Electrical Service

DANGER: Risk of electrical shock. Connect only to a

properly-grounded, dedicated 120 VAC, 15 A, 60 Hz circuit

protected by a Class A Ground-Fault Circuit-Interrupter (GFCI)

A licensed electrician must install a properly-grounded, dedicated

120 VAC, 15 A, 60 Hz circuit. The circuit must be protected by a

Class A ground-fault circuit-interrupter (GFCI).

Locate the wall box for the ﬂexible conduit to be used for this

circuit 6” (15.2cm) above the ﬂoor and 6” (15.2cm) to the right of

the toilet centerline.

6" (15.2cm)

Center Line

6" (15.2cm)

120 VAC, 15 A,

60 Hz Circuit

Kohler Co. 5 1021800-2-B

3. Install the Liquid-Tight Conduit

NOTICE: If local codes will not permit you to use a liquid-tight,

ﬂexible conduit, do not attempt to install this toilet.

CAUTION: Risk of product or property damage. Do not use

rigid conduit to install this toilet. Rigid conduit may put

excessive stress on the toilet, which can cause damage to the

toilet tank or the installation site.

Cut a 36” (91.4cm) length of liquid-tight conduit. Use an

appropriate liquid-tight connector to connect the conduit to the

underside of the junction box located on the inside rear wall of

the toilet tank.

Liquid Tight Connector Junction Box

Liquid Tight Conduit

(36" (91.4cm))

1021800-2-B 6 Kohler Co.

4. Install the New Toilet

Install or relocate the supply and outlet as necessary to conform

to the roughing-in dimensions.

Install a supply shut-off valve.

Record the model number in the Homeowners Guide.

Lay the toilet down onto a padded surface.

From the bottom of the toilet, ﬁrmly press a new wax seal around

the toilet outlet.

Remove the temporary rag (if used) from the toilet ﬂange hole.

Align and lower the toilet over the ﬂange and T-bolts.

CAUTION: Risk of external leakage. Do not lift or rock the

bowl after placement. If you break the watertight seal, you must

install a new wax seal.

Apply your full body weight around the toilet to set the seal.

Place the plastic bolt cap bases over the T-bolts in the ″up″

position as marked.

Place the metal washers and nuts on the plastic bolt cap bases

and T-bolts.

CAUTION: Risk of product damage. Overtightening may cause

breakage or chipping of vitreous china.

Carefully tighten the nuts.

Bottom of Bowl

Wax Seal Bolt Cap

Nut

Washer

Bolt Cap Base

T-Bolt

Closet Flange

Kohler Co. 7 1021800-2-B

Install the New Toilet (cont.)

NOTE: To achieve optimum performance, be sure the bowl is level.

CAUTION: Risk of product damage. Protect the vitreous china

from exposure to the saw blade when cutting off excess T-bolt

length.

If the T-bolts extend more than 1/4″(6mm) over the top of the

nuts, cut off the excess.

Attach the bolt caps.

1021800-2-B 8 Kohler Co.

5. Make the Final Electrical Connections

NOTICE: An electrician should make the ﬁnal electrical connections

using wire nuts or other terminations as required by applicable local

codes. Connect the black wire to the line, the white wire to neutral,

and the green wire to ground.

Cut the liquid-tight, ﬂexible conduit to a length suitable to make

a connection to the wall box.

Assemble the connectors on the conduit.

Pull the wall box wires through the conduit to the junction box

mounted on the rear inside wall of the toilet tank.

Connect the conduit at both ends.

Using the appropriate terminations, make the electrical

connections in the junction box on the toilet tank.

Install the junction box cover using the self-tapping screws

provided.

Liquid Tight Conduit

Junction Box Cover

Junction Box

Screw

Pull Wall Box Wires Through

Liquid Tight Conduit

Kohler Co. 9 1021800-2-B

6. Complete the Installation

Remove the Packing Material

NOTE: Do not remove the pump hose clamps.

Remove and discard the protective materials used in shipping.

Cut the wire tie holding the pump to the back wall of the toilet.

Discard the wire tie.

If the pump has shifted during shipping or installation, reposition

it so it is not touching the back or side wall of the toilet.

Complete Connections

Connect the supply shut-off valve to the toilet supply shank.

Open the supply shut-off valve slowly to check for leaks. If the

connections have been properly assembled, a slight tightening of

the nuts should stop any leakage.

Install the toilet seat according to the packed instructions.

Plug the toilet electrical cord into a Class A Ground-Fault

Circuit-Interrupter (GFCI).

Adjust the tank water level to the proper marked waterline by

rotating the threaded rod clockwise to raise the water level or

counterclockwise to lower the water level.

Carefully set the cover onto the tank.

Supply Shut-Off Valve

Connection

Tubing

Ferrule

Supply Shank

Seal Washer

Tubing

Ferrule

Fill Valve Nut

Coupling

Nut

Supply

Shut-Off

Valve

Comp. Nut

Coupling

Nut

Comp.

Washer

Comp.

Nut

Adjusting The Water Level

Float

Waterline

1021800-2-B 10 Kohler Co.

Andere Handbücher für K-3399

Inhaltsverzeichnis

Sprachen:

Andere Kohler Toilette Handbücher

Kohler

Kohler K-3997 Montageanleitung

Kohler

Kohler S-TRAP K-3991T-S2 Bedienungsanleitung

Kohler

Kohler REACH K-3983T-HC Bedienungsanleitung

Kohler

Kohler K-4026 Montageanleitung

Kohler

Kohler K-5402 Montageanleitung

Kohler

Kohler K-8297KR-HC-0 Montageanleitung

Kohler

Kohler S-TRAP K-3983T Bedienungsanleitung

Kohler

Kohler Santa Rosa K-3811-33 Bedienungsanleitung

Kohler

Kohler K-17640 Bedienungsanleitung

Kohler

Kohler K-5889X Montageanleitung

Kohler

Kohler Escale K-3588-96 Bedienungsanleitung

Kohler

Kohler VEIL K-5401T Bedienungsanleitung

Kohler

Kohler C3-430 Bedienungsanleitung

Kohler

Kohler C3-201 Quiet-Close K-4744 Bedienungsanleitung

Kohler

Kohler PERSUADE K-3654T-W Bedienungsanleitung

Kohler

Kohler K-20168T-SL-CG1 Bedienungsanleitung

Kohler

Kohler Intelligent Toilet Montageanleitung

Kohler

Kohler Escale K-25089T-S Bedienungsanleitung

Kohler

Kohler French Curve K-4653T-U Bedienungsanleitung

Kohler

Kohler Wellworth K-4468 Bedienungsanleitung

Kohler

Kohler K-3506 Montageanleitung

Kohler

Kohler K-5401 Bedienungsanleitung

Kohler

Kohler K-3322 Montageanleitung

Kohler

Kohler K-11844 Montageanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung