Kohler K-4026 Bedienungsanleitung

Installation Guide

Toilet with Bidet Seat

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-4026

1221754-2-C

Important Information

NOTE: This product is designed for installation with the electrical and water supplies located through the

wall.

Grounding Instructions

•This product should be grounded. In the event of an electrical short circuit, grounding reduces the

risk of electric shock by providing an escape wire for the electric current. This product is equipped

with a cord having a grounding wire with a grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded.

WARNING: Risk of electric shock. Improper use of the grounding plug can result in a risk of

electric shock.

•If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either

ﬂat blade terminal. The wire with insulation having an outer surface that is green with or without

yellow stripes is the grounding wire.

•Check with a qualiﬁed electrician or service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the product is properly grounded.

•This product is factory equipped with a speciﬁc electric cord and plug to permit connection to a

proper electric circuit. Make sure that the product is connected to an outlet having the same

conﬁguration as the plug. No adapter should be used with this product. Do not modify the plug

provided — if it will not ﬁt the outlet, have the proper outlet installed by a qualiﬁed electrician. If

the product must be reconnected for use on a different type of electric circuit, the connection should

be made by qualiﬁed service personnel.

Tools and Materials

Before You Begin

WARNING: Risk of electric shock. Disconnect the power before servicing.

WARNING: Risk of electrical shock. Connect only to a properly-grounded, grounding-type

receptacle which is protected by a Ground-Fault Circuit-Interrupter (GFCI). Do not remove the

grounding pin or use a grounding adapter.

CAUTION: Risk of hazardous gases. If a new toilet is not installed immediately, temporarily place

a rag in the ﬂoor ﬂange opening.

IMPORTANT! The water supply input pipe must be a minimum of 1/2″copper pipe or 3/4″PEX tube to

provide the minimum water ﬂow for this product to operate properly.

Masking

Tape

Pencil or Felt

Tip Marker

Assorted Screwdrivers

Supply Stop 5/16" x 2-1/4" T-Bolts

Drill and 1/4" bit

Caulk Gun Caulk

Rags

Silicone Grease

or Soap

Socket Wrench

with 1/2" Deep Socket

1221754-2-C 2 Kohler Co.

Before You Begin (cont.)

NOTICE: The Canadian Electric Code requires receptacles installed in bathrooms to be located at least

39-3/8″(1000 mm) from a bath or shower if practical, but in no case less than 19-11/16″(500 mm). If the

installation is in Canada, install this unit in accordance with the Canadian Electrical Code, Part 1.

Observe all local plumbing and building codes.

Carefully inspect the new toilet for any damage.

There is a wiring schematic on the inside of the access cover.

Consult the Homeowners Guide for user directions.

Consult the Homeowners Guide for troubleshooting instructions.

Kohler Co. 3 1221754-2-C

1. Prepare the Site

WARNING: Risk of electrical shock. Connect only to a properly-grounded, grounding-type

receptacle which is protected by a Ground-Fault Circuit-Interrupter (GFCI). Do not remove the

grounding pin or use a grounding adapter.

CAUTION: Risk of hazardous gases. If the new toilet is not installed immediately, temporarily

place a rag in the closet ﬂange.

NOTE: If the rough-in distance is less than 12″(305 mm) the seat may strike the wall when it is opened.

Conﬁrm the rough-in is 12″(305 mm) before installing the toilet.

Turn off the water supply.

Remove the old toilet.

Remove the wax residue from the ﬂange.

NOTE: T-bolts are not included. T-bolts should be 2-1/4″(57 mm) in length. Longer bolts will cause

difficulty in installation.

Install two 5/16″diameter x 2-1/4″long T-bolts into the ﬂoor ﬂange.

Mark the centerlines for the outlet on the ﬂoor.

Install the electrical supply at the location shown.

Install the water supply at the location shown.

(152 mm)

12"

(305 mm)

2-3/4" (70 mm)

Supply Stop

Floor Flange

T-Bolt

Scrape off the old

wax seal.

Centerline

1221754-2-C 4 Kohler Co.

2. Install the Tank

CAUTION: Risk of property damage. Do not rock or lift the tank after placement. The seal created

by the wax ring may be broken, resulting in leaking.

CAUTION: Risk of product damage. Do not push down on any part of the tank assembly other than the

cylinder. Damage may occur.

Position the wax ring on the ﬂoor ﬂange.

Remove the outlet gasket.

Align the tank over the ﬂoor ﬂange and T-bolts.

Lower the tank onto the ﬂoor ﬂange with the slots in the base of the tank aligned with the T-bolts.

Carefully align the tank on the centerline.

CAUTION: Risk of product damage. Only apply downward pressure to the tank cylinder. Do not press

on the tank components other than the cylinder, or damage may occur.

Press down evenly on the rim of the cylinder to set the wax ring.

Reinstall the outlet gasket.

Press here on

cylinder.

Floor Flange

Tank

T-Bolts

Centerlines

Wax Ring

Outlet Gasket

Kohler Co. 5 1221754-2-C

3. Secure the Tank

CAUTION: Risk of product damage. Do not overtighten the mounting nuts. Do not cut or shorten the

T-bolts.

Install a washer on each T-bolt.

Thread a nut onto each T-bolt.

Hand tighten the nuts.

Wrench tighten the nuts one quarter turn past hand tight with a socket wrench.

Connect the water supply hose to the open port on the elbow.

Connect the water supply hose to the water supply stop.

Conﬁrm the cap on the elbow is tight.

Open the water supply stop.

T-Bolt

Washer

Nut

Base of

Tank Assembly

Connect to the

supply stop.

Flexible Hose

Capped

Port

Water Supply

Hose

1221754-2-C 6 Kohler Co.

4. Check the Waterline

CAUTION: Risk of property damage. Before use, open the inlet valve using the valve adjustment

screw to avoid overﬂow.

NOTE: The waterline is marked inside the tank by a notch and a label.

Turn the valve adjustment screw counterclockwise to open the motorized valve.

Allow the tank to ﬁll. Check the water level in the tank.

To adjust the water level, use a ﬂat-blade screwdriver to carefully turn the adjustment rod on the

inlet valve. Turning the rod counterclockwise will lower and clockwise will raise the water level.

If further adjustment is required, remove several inches of water from the tank and allow it to reﬁll.

Conﬁrm the water level is correct. Repeat until the correct water level is reached.

Turn off the water supply.

Valve Adjustment

Waterline

Adjustment

Waterline

Flexible Hose

Notch

Kohler Co. 7 1221754-2-C

5. Install the Collar

CAUTION: Risk of product damage. Conﬁrm the wires and water supply hose will not interfere with the

vitreous shell as it is lowered into place. The vitreous shell may cause damage to the wires or hose.

NOTE: It may be necessary to disconnect the water supply hose and tape it to the ﬂoor with the wires to

keep it clear of the vitreous while it is lowered into place.

Place the pump wiring harness, level switch wire, reﬁll tube, electrical plug, and bidet wiring plug

on the ﬂoor at the location of the rear access opening and tape them on the centerline so they will

not interfere with the vitreous shell.

Apply silicone grease or soap to the inside bottom edges of the collar where it will contact the outlet

gasket.

Install the collar onto the outlet gasket. Push the collar down ﬁrmly.

Clip the spray shield into place over the ﬁll valve.

Refill Tube

Tape

Level Switch

Wire

Electrical Plug

Pump Wiring

Harness

Bidet Wiring

Harness

Spray Shield

Collar

Tank

Flexible

Hose

Apply silicone grease

or soap to the inside.

1221754-2-C 8 Kohler Co.

6. Install the Vitreous Shell

WARNING: Risk of personal injury. The vitreous shell weighs 105 lbs (36 kg). Use proper lifting

technique when handling the vitreous shell. Lift and position the vitreous shell with a partner.

CAUTION: Risk of product damage. Do not set the shell down hard. Gently lift and move the shell if it

is not placed correctly. If handled carelessly, the shell may chip or break.

With assistance, carefully pick up the vitreous shell and slowly lower it over the tank.

Remove the cap from the capped elbow port.

Connect the bidet hose to the elbow.

Make sure the trapway in the vitreous shell seats fully in the outlet gasket. If the vitreous shell does

not sit evenly on the ﬂoor, the trapway may not be properly seated.

Adjust the vitreous shell as needed until the trapway is properly seated.

Reconnect the water supply hose to the water supply if it was disconnected.

Connect the Wires

CAUTION: Risk of personal injury. Make sure the plug (if plug-in connection is used) and

receptacle are dry. If any moisture is present, allow the area to dry before plugging the unit in.

Remove the tape from the ﬂoor wires and toilet.

Connect the level switch and reﬁll tube.

Connect the bidet wiring harness and pump wiring harness.

Vitreous

Tank

Collar

Bidet

Wiring Harness

Pump

Wiring Harness

Level Switch

Refill Tube

Kohler Co. 9 1221754-2-C

7. Install the Remote Control

Determine the desired location of the remote control docking station.

Position the docking station in the desired location and mark the location of the screw holes.

Remove the docking station.

Drill 1/4″holes at each of the screw locations.

Install anchors in each of the holes.

Remove the backing on the two-sided tape.

Attach the docking station to the wall using the two supplied screws.

Install the screw hole covers.

Install the batteries in the remote control (consult the Homeowners Guide for instructions if

needed).

Place the remote control on the docking station.

38" (965 mm) - 66" (1676 mm)

36"

(914 mm)

Docking Station

Remote Control

Screw

Double-Sided Tape

Anchor

Docking Station

Cover

1221754-2-C 10 Kohler Co.

Andere Handbücher für K-4026

Inhaltsverzeichnis

Sprachen:

Andere Kohler Toilette Handbücher

Kohler

Kohler K-3654-7 Montageanleitung

Kohler

Kohler STERLING Windham Pro Force 402210 Bedienungsanleitung

Kohler

Kohler ADAIR K-75925T Bedienungsanleitung

Kohler

Kohler K-77780 Bedienungsanleitung

Kohler

Kohler K-3519 Bedienungsanleitung

Kohler

Kohler K-28413H Montageanleitung

Kohler

Kohler S-TRAP K-3991T Bedienungsanleitung

Kohler

Kohler WELLWORTH LITE K-3420 Bedienungsanleitung

Kohler

Kohler Hyten K-25875 Bedienungsanleitung

Kohler

Kohler K-3513 Montageanleitung

Kohler

Kohler VEIL WALL FACED Bedienungsanleitung

Kohler

Kohler K-11456 Montageanleitung

Kohler

Kohler Irvine E915 Bedienungsanleitung

Kohler

Kohler Santa Rosa K-3811-33 Bedienungsanleitung

Kohler

Kohler Karess S-TRAP K-5331T-S Datenblatt

Kohler

Kohler K-3900T-2 Bedienungsanleitung

Kohler

Kohler K-3429 Montageanleitung

Kohler

Kohler K-20184K Montageanleitung

Kohler

Kohler S-TRAP K-3983T Bedienungsanleitung

Kohler

Kohler FAMILY CARE S-TRAP K-23191T-NS Bedienungsanleitung

Kohler

Kohler K-3324 Montageanleitung

Kohler

Kohler Veil Comfort Height Montageanleitung

Kohler

Kohler K-3379 Bedienungsanleitung

Kohler

Kohler K-3901 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung