Kohler K-3901 Bedienungsanleitung

Installation Guide

Toilet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-3901

1212876-2-B

Important Information

NOTE: This product is designed for installation with the electrical and water supplies located through

either the wall or the ﬂoor.

Grounding Instructions

•This product should be grounded. In the event of an electrical short circuit, grounding reduces the

risk of electric shock by providing an escape wire for the electric current. This product is equipped

with a cord having a grounding wire with a grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded.

WARNING: Risk of electric shock. Improper use of the grounding plug can result in a risk of

electric shock.

•If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either

ﬂat blade terminal. The wire with insulation having an outer surface that is green with or without

yellow stripes is the grounding wire.

•Check with a qualiﬁed electrician or service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the product is properly grounded.

•This product is factory equipped with a speciﬁc electric cord and plug to permit connection to a

proper electric circuit. Make sure that the product is connected to an outlet having the same

conﬁguration as the plug. No adapter should be used with this product. Do not modify the plug

provided — if it will not ﬁt the outlet, have the proper outlet installed by a qualiﬁed electrician. If

the product must be reconnected for use on a different type of electric circuit, the connection should

be made by qualiﬁed service personnel.

Tools and Materials

Drill with Assorted Bits Assorted

Screwdrivers Wax Ring

Adjustable Wrench

Plus:

• Protective Material

• Tape

• Water Hammer Arrestor

Offset Screwdriver

1212876-2-B 2 Kohler Co.

Before You Begin

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of electric shock. For plug-in installations/wall-mounted electrical supply:

Connect only to a properly-grounded, grounding-type receptacle which is protected by a dedicated

120 V, 15 A minimum, 60 Hz Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device

(RCD). Do not remove the grounding pin or use a grounding adapter.

CAUTION: Risk of personal injury. This toilet weighs approximately 100 lbs (45 kg). Lift the toilet

with two people, employing proper lifting technique.

CAUTION: Risk of hazardous gases. If a new toilet is not installed immediately, temporarily place

a rag in the ﬂoor ﬂange opening.

CAUTION: Risk of property damage. This toilet is not intended to be installed in buildings where

temperatures will drop below 32°F (0°C). The design of the toilet makes it difficult to remove all

water from the tank. If frozen, the water could damage the tank resulting in leaking.

IMPORTANT! Use the supply hoses provided with the ﬁxture. Do not reuse the previously installed

hoses.

NOTICE: Follow all local plumbing and electrical codes.

IMPORTANT! This product requires a minimum static pressure of 30 psi (206.8 kPa) for satisfactory rim

wash performance.

IMPORTANT! There are two different remote control options for this model. Setup for the K-7420

premium remote control is included in this manual. If you do not have the premium remote control, refer

to the instructions packed with the K-7421 standard remote control for setup information.

2 Bushings

2 Caps

2 #10 x 1-1/2"

Screws

Supply Hose Clip

2 Mounting Blocks

(4) 5/16" x 2-1/2" Lag Bolts

(4) 5/16" Lag Bolt Anchors

Back Cover

(Through-the-Floor

Installations)

Parts Bag Contents

Other Parts

Kohler Co. 3 1212876-2-B

Before You Begin (cont.)

IMPORTANT! If the remote control option with this model is the K-7420 premium remote control, install

the remote control before installing the toilet. It is more difficult to install the remote control after the toilet

is in place.

Carefully inspect the new toilet for damage.

Consult the online users guide at kohler.com for more information.

Conﬁrm all parts below are included before beginning the installation.

Parts Bag Contents

(4) 5/16″x 2-1/2″Lag Bolts

(4) 5/16″Lag Bolt Anchors

2 Mounting Blocks

2 Plastic Caps

2 #10 x 1-1/2″Screws

2 Bushings

Other Parts

Back Cover (used in through-the-ﬂoor installations)

Supply Hose

Clip

1212876-2-B 4 Kohler Co.

Roughing-In - Wall Mount Electrical and Water Supply

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of electrical shock. For plug-in installations/wall-mounted electrical supply:

Connect only to a properly-grounded, grounding-type receptacle which is protected by a

Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). Do not remove the

grounding pin or use a grounding adapter.

NOTICE: The locations for the supply shut-off, electrical outlet, and docking station cord are suggested

locations. Make sure all installations adhere to applicable codes and standards.

IMPORTANT! Locating the supply stop behind the toilet will make it difficult to remove the back panel.

It may be necessary to remove the toilet to service items behind the back panel if the supply stop extends

more than 3″(76 mm) from the wall.

IMPORTANT! Consult the remote control documentation for the recommended remote control location.

IMPORTANT! Do not install any items behind the toilet that will interfere with the cover when it is

raised. All decorative items should be at least 37″(940 mm) high to allow clearance for the cover.

The supplied power cord is 56″(1422 mm) in length. Install the GFCI or RCD protected outlet

within 56″(1422 mm) of the toilet location.

The toilet is equipped with a motion sensor to automatically open the cover when movement is

sensed. This sensor has a maximum range of 51-1/2″(1300 mm). Sensitivity can be adjusted or

turned off using the User Interface.

The toilet is equipped with a sensor to automatically open the seat when the light is interrupted.

The sensor is located on the right side of the toilet. This sensor has a maximum range of 8″(203

mm). Keep this area free of obstructions.

Optional

Supply,

1/2" OD

Compression

Outlet Thread

Front of Bowl

Finished

Wall

L Of Outlet

Outlet

1/2" OD

Compression

Outlet Thread

Optional Supply

1/2" OD Compression

Outlet Thread

25-3/4"

(654 mm)

Ø 2-5/8"

(67 mm)

14-1/2"

(368 mm)

25-1/4"

(641 mm)

13-5/8"

(346 mm)

10-13/16" (275 mm)

3-3/4" (95 mm),

3-9/16" (90 mm) Min

29-1/2" (749 mm)

12"

(305 mm)

12" (305 mm)

15-5/8"

(397 mm)

2-1/4"

(57 mm)

1-3/4"

(44 mm),

1-1/2"

(38 mm)

Min

36-1/4"

(921 mm)

Power Cord

Reaches

56" (1422 mm)

4-3/4" (121 mm)

2" (51 mm)

17-7/8"

(454 mm)

(152 mm)

8" (203 mm)

Kohler Co. 5 1212876-2-B

Roughing-In - Wall Mount Electrical and Water Supply (cont.)

1/2″OD compression supply stop outlet is required unless an adapter is used.

Installation of a water hammer arrestor is required.

1212876-2-B 6 Kohler Co.

Roughing-In - Through-the-Floor Water and Electrical

NOTICE: The locations for the supply shut-off, electrical outlet, and docking station cord are suggested

locations. Make sure all installations adhere to applicable codes and standards.

IMPORTANT! Do not install any items behind the toilet that will interfere with the seat when it is raised.

All decorative items should be at least 37″(940 mm) high to allow clearance for the seat.

IMPORTANT! Consult the remote control documentation for the recommended remote control location.

The supplied power cord is 56″(1422 mm) in length.

The toilet is equipped with a motion sensor to automatically open the cover when movement is

sensed. This sensor has a maximum range of 51-1/2″(1300 mm). Sensitivity can be adjusted using

the User Interface.

The toilet is equipped with a seat actuator sensor, located on the right side of the toilet. This sensor

has a maximum range of 8″(203 mm). Keep this area free of obstructions.

1/2″OD compression supply stop outlet is required unless an adapter is used.

Installation of a water hammer arrestor is required.

Front of Bowl

25-3/4" (654 mm)

Finished Wall

Ø 1-1/2" (38 mm)

Water Supply Hole

Ø 1-1/4" (32 mm)

Power Supply Hole

Ø 2-5/8"

(67 mm)

14-1/2"

(368 mm)

25-1/4"

(641 mm)

10-13/16" (275 mm)

3-3/4" (95 mm),

3-9/16" (90 mm) Min

29-1/2" (749 mm)

12"

(305 mm)

12"

(305 mm)

15-5/8"

(397 mm)

2-1/4"

(57 mm)

1-3/4"

(44 mm),

1-1/2"

(38 mm)

Min

36-1/4"

(921 mm)

4-3/4" (121 mm)

17-7/8"

(454 mm)

L Of Outlet

13-5/8"

(346 mm)

Kohler Co. 7 1212876-2-B

1. Prepare the Site

WARNING: Risk of electric shock. Disconnect power before installation or servicing.

WARNING: Risk of electric shock. Connect only to a properly-grounded, grounding-type

receptacle which is protected by a 120 V, 15 A minimum, 60 Hz Ground-Fault Circuit-Interrupter

(GFCI) or Residual Current Device (RCD). Do not remove the grounding pin or use a grounding

adapter.

WARNING: Risk of electrical shock. For hardwire installations/through-ﬂoor electrical supply:

Connect only to a properly-grounded, dedicated circuit protected by an Class A Ground-Fault

Circuit-Interrupter (GFCI) or Residual Current Device (RCD).

NOTE: The electrical outlet and water supply may also be located behind the toilet. If it is located behind

the toilet, the water supply stop must extend no more than 3″(76 mm) beyond the ﬁnished wall. If located

behind the toilet, the supply stop must be a model that connects at a 90° angle. The handle should be

easily accessible.

NOTE: Locating the supply stop behind the toilet will make it difficult to remove the back panel. It may

be necessary to remove the toilet to service items behind the back panel if the supply stop extends more

than 3″(76 mm) from the wall.

Install the Remote Control

NOTE: If the K-7421 standard remote control is included with your model, no cord is required.

Install the remote control docking station now following the installation instructions supplied with

the remote control.

Install the Water Supply

(152 mm)

12" (305 mm) From

Finished Wall

Recommended,

11-3/4" (298 mm) Min

Supply Stop

Floor Flange

GFCI/RCD

Protected

Receptacle

3" (76 mm) Max

When Located

Behind Toilet

(102 mm)

K-7420 Premium

Dock Power Cord

(not required

for K-7421)

2" (51 mm)

Ø 1-1/2" (38 mm)

Water Supply Hole

(for through-the-floor

installations only)

Ø 1-1/4" (32 mm)

Power Supply Hole

(for through-the-floor

installations only)

2-5/8"

(67 mm)

1-5/8"

(41 mm)

8" (203 mm)

1212876-2-B 8 Kohler Co.

Prepare the Site (cont.)

IMPORTANT! When installing the supply hose, connect it to the toilet ﬁrst, then the supply stop.

NOTE: The supplied water supply hose is 18″(457 mm) in length. The supplied hose must be used for

this installation.

Install the water supply and supply stop.

Install a water hammer arrestor to the supply stop or water supply line.

Flush the water supply line into a pail or other container to remove all debris.

Install the Electrical Service

NOTE: The suppled power cord is 56″(1422 mm) in length.

Locate a dedicated 120 V, 15 A minimum, 60 Hz grounding-type receptacle, protected by a GFCI or

RCD, within 56″(1422 mm) of the back of the toilet.

Install External Speaker Wires (optional)

If external speakers will be used, install the speaker wires at this time.

Kohler Co. 9 1212876-2-B

2. Prepare the Installation Location

IMPORTANT! Risk of product damage. If T-bolts are left in place, they will damage the toilet. Make sure

they are removed before moving the toilet into place.

If there are T-bolts extending from the ﬂange, remove them. T-bolts are not required for this

installation.

Cut out the inside of the ﬂange area on the template.

Position the template with the hole positioned over the ﬂange. It is critical that the centerlines

marked on the template are centered on the ﬂange.

Secure the template to the ﬂoor with tape.

IMPORTANT! Because of the unique design of this toilet, the width of the bottom edges of the toilet will

vary. The following steps are required because of this variation.

Conﬁrm the template is correctly positioned and centered over the ﬂange.

Position the toilet on the template. Make sure the front of the base of the toilet is aligned with the

markings on the template.

Position the toilet so an equal amount of shaded area is visible on each side of the template.

Conﬁrm the toilet is centered by measuring the amount of space on each side of the template.

Directly under the screw holes on each side of the toilet, accurately mark the bottom edge of the

base. The mark should intersect the lines labeled ″C″and ″A″or ″B″on each side of the template.

Template

Screw Hole

Center the toilet

on the template.

Top View

For Wall Supply

Installations Only

For Through-

the-Floor

Supplies Only

Tape

Flange

Flange Centerlines

1212876-2-B 10 Kohler Co.

Andere Handbücher für K-3901

Inhaltsverzeichnis

Sprachen:

Andere Kohler Toilette Handbücher

Kohler

Kohler K-3609 Montageanleitung

Kohler

Kohler K-4026 Montageanleitung

Kohler

Kohler K-3322 Montageanleitung

Kohler

Kohler K-18154 Bedienungsanleitung

Kohler

Kohler K-4352 Montageanleitung

Kohler

Kohler K-3519 Bedienungsanleitung

Kohler

Kohler REACH K-3991K-HC Bedienungsanleitung

Kohler

Kohler OVE K-17629T-2 Bedienungsanleitung

Kohler

Kohler K-3509 Montageanleitung

Kohler

Kohler Veil Comfort Height Montageanleitung

Kohler

Kohler K-1976 Bedienungsanleitung

Kohler

Kohler SAN RAPHAEL GRANDE K-8688T-HC Bedienungsanleitung

Kohler

Kohler S-TRAP K-3991T Bedienungsanleitung

Kohler

Kohler AERODYNE K-3869T-S Bedienungsanleitung

Kohler

Kohler K-10349 Bedienungsanleitung

Kohler

Kohler K-3797 Montageanleitung

Kohler

Kohler SAN SOUCI CLASS FIVE K-21865T-S Bedienungsanleitung

Kohler

Kohler Reve Comfort Height K-3797-0 Montageanleitung

Kohler

Kohler K-3357 Bedienungsanleitung

Kohler

Kohler K-3482K-NS Montageanleitung

Kohler

Kohler K-20797T-S Bedienungsanleitung

Kohler

Kohler NUMI 2.0 Montageanleitung

Kohler

Kohler K-3447 Bedienungsanleitung

Kohler

Kohler K-2590 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung