Kohler K-4026T Bedienungsanleitung

·We appreciate your commitment to Kohler quality. Please

take a few minutes to review this manual before you start

installation. If you encounter any installation or

performance problems, please don t hesitate to contact us.

Thanks again for choosing Kohler Company.

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

NOTES

DANGER: Risk of electric shock.

WARNING: Risk of electric shock.

CAUTION: Risk of hazardous gases.

NOTICE: Follow all local plumbing and electrical codes.

NOTICE:

WARNING: Risk of electric shock for hardwire

installations/through-floor electrical supply:

Disconnect power

before servicing.

Connect only to

circuits protected by Ground-Fault Circuit-Interrupters

(GFCI s) or Earth-Leakage Circuit-Breakers (ELCB s).

If a new toilet

is not installed immediately, temporarily place a rag in

the floor flange opening.

Receptacles installed in bathrooms to be located at

least 1 meter from a bathtub or shower if practical, but in no

case less than 500 mm.

Observe all local plumbing and building codes.

Carefully inspect the new toilet for damage.

Water and electrical supplies may be wall mounted.

There is a wiring schematic on inside of the of the junction

box cover.

Connect only to properly-grounded, dedicated

220~240V, 16A, 50Hz circuit protected by a Class A

Ground-Fault Circuit-Interrupter (GFCI) or Earth-

Leakage Circuit-Breaker (ELCB).

WARNING: Must use 16A receptacle.

ORDERING INFORMATION

Integrated Toilet .........................................................K-4026T

Includes Remote Controller Assy.........................1106433

GFCI ELCB

500

220~240 16 50

K-4026T

........................................................1106433

...................................................

INSTALLATION INSTRUCTIONS

INTEGRATED TOILET

K-4026T

-1-

, 2010

BEFORE YOU BEGINBEFORE YOU BEGIN

18 E 201206

1144585-T01-A

TOOLS AND MATERIALS REQUIRED (Not

supplied)

Adjustable Wrench 2

Tape measure

Masking tape

Knife

Supply stop(with filter)

Assorted screwdrivers

Plastic anchor

Screw

T-Bolts

Flange

Expansion Bolt Kits

Fig.#1

Unit: mm

349

424

395

528

670

779

405

155

Front of Bowl

Bottom View

Note:

Plastic Anchor: Recommend use outside dia 10mm.

Screw: Recommend using M6 screw to match the plastic

anchor.

10mm

Kohler reserves the right to change marked dimensions without prior notice.

-2-

of Outlet

305

Finished Wall

Finished Floor

Reference Value

ROUGHING-IN

1144585-T01-A

SPECIFICATIONS

0~40

Water Supply Pressure

Minimum Distance from Hole to Wall

Flushing Volume

0.7kgf/cm ( ) ~ 7.5 kgf/cm (0.07MPa. ( ) ~ 0.74MPa.)

305mm

4.8L

0.7kgf/cm (Dynamic Pressure) ~ 7.5 kgf/cm

(0.07MPa. (Dynamic Pressure) ~ 0.74MPa.)

Electrical Power

220~240V 50Hz 1800W

Power Cord Length

1.5m

About 1.5m

Outline Dimension of Product

670mmX 424mmX 528mm

670mm x 424mm x 528mm

Product Weight

46kg

About 46Kg

Operation Environment

-3-

SIMPLIFIED DIAGRAM OF THE UNITSIMPLIFIED DIAGRAM OF THE UNIT

Note: See "Homeowner's Guide" for detailed specifications of

the bidet seat.

Bumper x 2

Sensor Area

Seat Cover (Antibacterial)

()

Auxiliary Panel

Actuation Switch

Seat (Antibacterial)

()

Seat Sensor Area

Nozzle (Antibacterial)

()

Seat Sensor Area

"Dryer" Key

"Rear" Key

"Front" Key

"Power" Key

Light Sensor

Signal Receiving Area

Fig.#2

1144585-T01-A

Fig.#3

Fig.#4

A. Hold the rim of the vitreous shell and take out the toilet.

Risk of personal injury and product damage!

Please do not hold the rim of the bidet seat

when lifting the toilet. As the toilet is heavy,

please seek for help if necessary.

Warning:

B. When taking out the toilet from the carton box, please pay

special attention to the bottom of the toilet to avoid the

tank assembly to drop out.

-4-

PREPARATIONS BEFORE INSTALLATIONPREPARATIONS BEFORE INSTALLATION

Toilet

Tank Assy.

1144585-T01-A

b. Take out the tank assembly from the vitreous shell and

put it on the floor.

c. Remove the EPE foam from the tank.

d. Remove the gasket and the collar. d.

EPE Foam

C. Take out the tank.

a. Place an 800mm x 600mm cushion on the floor and

then put the whole toilet on it.

Operate with care to avoid scratching the surface

of the vitreous shell.

Note:

a. 800mm x 600mm

Actuation Switch

Fig.#5a

Fig.#5b

Fig.#5c

-5-

D. Place every part on the floor and ready for installation. D.

Fig.#6

Collar

Gasket

1144585-T01-A

-6-

B. Roughing-In

DANGER: Risk of electric shock.

NOTE:

WARNING: Risk of electric shock.

Disconnect power

before servicing.

This product is designed to work with wall mounted

electrical and water supplies. It is shown in the roughing-in.

Connect only to

circuits protected by Ground-Fault Circuit-Interrupters

(GFCI s) or Earth-Leakage Circuit-Breakers (ELCB s).

Keep bath and shower away from electrical parts

(such as remote controller, receptacle, audio input

apparatus and so on).

When the electrical supply is mounted on the wall, a GFCI or

ELCB protected and water proof receptacle is required.

Follow the dimensional information exactly when installing a

hardwire electrical supply.

(GFCI) (ELCB)

(

)

(GFCI)

(ELCB)

Fig.#7

Fig.#8

Remove old gasket from the floor and

closet flange with a putty knife.

Remove old T-bolts and discard them.

if a new toilet is not installed

immediately, temporarily stuff a rag in

the closet flange.

NOTICE:

Closet Flange

A. To Remove Existing Toilet

Turn off the water supply. Flush the toilet, and use a sponge

to remove the remaining water from the tank and bowl.

Disconnect the supply shut-off valve (if present), and remove

the old tank and bowl.

()

INSTALLATION

150mm

305mm

70mm

Supply Stop (with filter)

() GFCI-Protected 16A Receptacle(water proof)

The wall location of the electrical and

water supply are interchangeable.

Floor Flange

T-Bolts

1144585-T01-A

D. Install the T-Bolts

Install two new 8mm (5/16") diameter

T-bolts into the floor flange.

Do not use white cement or high lime

content cements to install this toilet.

The expansion of cement due to a rise

in temperature may make the toilet

crack or cause damage. Kohler is not

responsible for any damage caused by

installation with the use of cement.

Install the Electrical Service

NOTE: This product is designed for installation with the

electrical supply located through the wall. Both types are

illustrated. Refer to the dimensional information for your

chosen installation.

Follow the dimensional information exactly when installing a

hardwire electrical supply.

Install the Water Service

NOTE:

This product is designed for installation with the water

supply located through the wall. Both types are illustrated.

Refer to the dimensional information for your chosen

installation.

A floor mounted water supply stop must be no higher

than 70mm from the floor.

Install the water supply. If you are installing a floor supply,

study the dimensional information illustrated carefully.

C. Install the Electrical Service and Water

Supply

DANGER: Risk of electric shock.

DANGER: Risk of electrical shock. For plug-in

installations/wall-mounted electrical supply:

DANGER: Risk of electrical shock. For hardwire

installations/through-floor electrical supply:

Disconnect power

before servicing.

Connect only to a properly-grounded, grounding-type

receptacle which is protected by a Ground-Fault

Circuit-Interrupter (GFCI). Do not remove the

grounding pin or use a grounding adapter.

Connect only to a properly-grounded, dedicated

220~240V, 16A, 50Hz circuit protected by a Class A

Ground-Fault Circuit-Interrupter (GFCI) or Earth-

Leakage Circuit-Breaker (ELCB).

D. T

8mm (5/16") T

70mm

(GFCI)

220~240 16 50

T-Bolts

Floor Flange

Fig.#9

-7-

1144585-T01-A

F. Position the Tank

Mark the centerline on the floor.

Align the tank over the floor flange.

Lower the tank onto the floor flange. The T-bolts should align

with the mounting slots in the base of the tank.

Carefully align the tank on the centerline.

Position the tank on the T-bolts.

Do not push

down on any part of the tank assembly other than the

cylinder. Damage may occur.

Do not rock or

lift the tank after placement. The seal created by the

wax ring may be broken, resulting in leaking.

Position the loose end of the refill tube out the outlet ring.

CAUTION: Risk of product damage.

Fig.#11

Tank

Refill Tube

T-Bolts

Floor Flange

Centerlines

Outlet Ring

Press here on cylinder.

-8-

Fig.#10

E. Install the Wax Ring

Place the wax ring in the putty ring located on the tank.

1144585-T01-A

-9-

Fig.#14

G. Secure the Tank

CAUTION: Risk of product

damage.

Note:

Do not overtighten

the mounting nuts. Do not

shorten the T-bolts.

Place a washer on each T-bolt.

Thread a nut onto each T-bolt.

Hand tighten the nuts.

In case there is no floor flange,

please fix the tank with the expansion

bolt kits. Specific installation steps are

decided by the installer.

Fig.#12

Nut

Washer

T-Bolt

Base of

Tank Unit

H. Connect the Water

IMPORTANT! If this installation

replaces an existing toilet, a hose

other than the one shipped with the

water supply may be used. Use a

stainless steel, burst-resistant hose.

Connect the water.

Open the shut-off valve.

Fig.#13

I. Check the Waterline

NOTE:

IMPORTANT!

The waterline is a notch in the inside of the tank,

marked with a label.

Turn on the water supply.

Open the motorized valve by sliding the lever back into the

open position.

Verify the inlet valve is set to the correct waterline. Adjust if

needed.

To adjust the waterline, use a flathead screwdriver to gently

turn the adjustment rod counterclockwise to lower and

clockwise to raise the waterline setting.

The valve will not operate if the valve is locked.

Return the lever back into the unlocked position.

Stop the shut off value.

Waterline

Adjust waterline

Locked

Unlocked

1144585-T01-A

J. Remove cap on Tee Connector of flexible hose. J.

Fig.#15

K. Install Gasket and Collar

Place the wiring harness plug, level switch wire, and refill

tube on the floor so they extend out the rear access opening.

Tape them to the floor so they will not be pinched or

damaged.

Install the collar onto the tank.

Clip the spray shield into place over the fill valve.

Fix the gasket to the tank and press tight.

Fig.#16

Wiring Harness Plug

(Connected to Bidet Seat)

()

Refill Tube

Inlet Tube

Level Switch Wire

Wiring Harness Plug

(Connected to Pump)

()

Electrical Plug

Collar

Spray Shield

Tank

-10-

Tape

Tank

Refill Tube

Gasket

1144585-T01-A

Inhaltsverzeichnis

Andere Kohler Toilette Handbücher

Kohler

Kohler PERSUADE K-3654T-W Bedienungsanleitung

Kohler

Kohler S-TRAP K-23188T-ITHC Bedienungsanleitung

Kohler

Kohler K-3482K-NS Montageanleitung

Kohler

Kohler K-11899 Montageanleitung

Kohler

Kohler Touchless Flush Montageanleitung

Kohler

Kohler K-3654 Montageanleitung

Kohler

Kohler Sterling Windham 402015 Bedienungsanleitung

Kohler

Kohler K-31636-0 Bedienungsanleitung

Kohler

Kohler K-3997 Montageanleitung

Kohler

Kohler K-3900T-2 Bedienungsanleitung

Kohler

Kohler FLEUR WATERGUARD K-3417 AA Series Bedienungsanleitung

Kohler

Kohler Revival K-14224-TL Montageanleitung

Kohler

Kohler K-4026 Montageanleitung

Kohler

Kohler BANCROFT K-3827T Bedienungsanleitung

Kohler

Kohler REVE K-24766T-S Bedienungsanleitung

Kohler

Kohler REVE K-20766T-S Bedienungsanleitung

Kohler

Kohler BRAZN 1PC K-EX22378T-NS Bedienungsanleitung

Kohler

Kohler K-25042-SS-0 Bedienungsanleitung

Kohler

Kohler K4915 Bedienungsanleitung

Kohler

Kohler K-4026T-2A-0 Bedienungsanleitung

Kohler

Kohler REACH K-3856T-S Bedienungsanleitung

Kohler

Kohler K-12698X Montageanleitung

Kohler

Kohler K-17629MY Montageanleitung

Kohler

Kohler PORTRAIT LITE K-4217 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung