Kohler K-77780T-0 Bedienungsanleitung

English page 2-19

中文页码20-37

科勒（中国）投资有限公司

静安

制造商:

中国上海市宝山区丰翔路1955号邮编: 200444

Installation Guide

安装说明

KARING 2.0 INTELLIGENT TOILET

新悦2.0智能座便器

K-77780T-0

K-77780T-XP-0

KARING 2.0 INTELLIGENT TOILET

IOT

新悦2.0智能座便器

云智能版

1303729-T01-G

Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In

addition to proper installation, read all operating and safety instructions.

All information in these instructions is based upon the latest product information available at the time of publication.

Kohler China reserves the right to make changes in product characteristics, packaging, or availability at any time

without notice.

These instructions contain important care, cleaning, and warranty information - please leave instructions for the

consume.

We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start

installation. If you encounter any installation or performance problems, please don t hesitate to contact us. Thanks

again for choosing Kohler Company.

Please make sure there is enough space for toilet installation, and it will not influence door swing.

When install the product in the room, a stop valve shall be installed in a close proximity. For emergency circumstances,

the water inlet valve shall be stopped without using any tools; otherwise unexpected failure may cause the loss to the

customer.

Confirm discharge pit dimension distance is 305mm, pit dimension distance must be 292-350mm or the installation will

be compromised.

Confirm water supply stop must extend no more than 3mm beyond the finished wall or sink no more than 5mm below

finished wall or the installation will be compromised.

DN15mm or larger main water pipe is recommended to ensure following water supply requirements.

NOTES

DANGER: Risk of electric shock.Disconnect power before servicing.

WARNING: Risk of electric shock.Connect only to circuits protected by Ground-Fault Circuit-

Interrupters (GFCI s) or Earth-Leakage Circuit-Breakers (ELCB s).

CAUTION: Risk of hazardous gases.If a new toilet is not installed immediately, temporarily place

a rag in the floor flange opening.

NOTICE: Follow all local plumbing and electrical codes.

NOTICE:Receptacles installed in bathrooms to be located at least 1 meter from a bathtub or shower if

practical.

WARNING: Risk of electric shock for hardwire installations/through-floor electrical supply:

Connect only to dedicated 220V~, 50Hz, 10A circuit protected by Ground-Fault Circuit-Interrupters

(GFCI’s) or Earth-Leakage Circuit-Breakers (ELCB’s).

WARNING: Must use 10A receptacle.

Observe all local plumbing and building codes.

Carefully inspect the new toilet for damage.

Water and electrical supplies may be wall mounted.

BEFORE YOU BEGIN

I NSTALLATION INSTRUCTIONS

KARING 2.0 INTELLIGENT TOILET

K-77780T-0

KARING 2.0 INTELLIGENT TOILET(IOT)

K-77780T-XP-0

1303729-T01-G

Kohler Co.

Fig.#1

TOOLS AND MATERIALS REQUIRED (Not supplied)

Adjustable Wrench 2

Tape measure

Masking tape

Knife

Supply stop(with filter)

Assorted screwdrivers

Plastic anchor

Screw

T-Bolts

Flange

Expansion Bolt Kits

NOTE:

Plastic Anchor: Recommend use outside dia 10mm.

Screw: Recommend using M6 screw to match the plastic anchor.

Reference Value Unit: mm

ROUGHING-IN

Finished Wall

of Outlet Finished Floor Bottom View

Kohler reserves the right to change marked dimensions without prior notice.

Front of Bowl

Kohler Co.

1303729-T01-G

Fig.#2

SPECIFICATIONS

SIMPLIFIEDDIAGRAMOFTHEUNIT

Press dryer button to

activate dryer function

Press button to

activate rear wash

Light sensing area

Press button to

activate front wash

Bumper x 2

Seat Cover (Antibacterial*)

Auxiliary Panel

Fllush button

Nozzle

Seat (Antibacterial*)

Seat Sensor Area

* Power value testing condition: dynamic pressure 0.2MPa, inlet water temp 15°C.

Flush volume

Water efficiency

grade* Pit distance

Water pressure

Rated voltage

Rated power*

Max instantaneous power

Length of power line

Product outline dimension

Weight of product

Inlet water temp

Operation Environment

How to Use Piezoelectric Switch

NOTE: See "Homeowner's Guide" for detailed specifications of the bidet seat.

*Antibacterial: the seat and cover contains long term inorganic anti-bacteria material which will inhibit bacteria growth on surface, this does not represent the mildew and other incidental effects.

The antibacterial rate is more than 90%. (Perform test in accordance with GB21551.2-2010 requirements. Testing lab: China household electrical appliances testing institute; electromechanical

products testing technology center of Shanghai Entry-Exit inspection and quarantine bureau.)

1. Standby mode

Hold “ ” button (over 2s) to enter standby

mode. Details refer to “Standby mode” chapter

“Homeowner's Guide” on page 15.

2. Stop function

Press “ ” button to stop flushing, dryer, air

purification, one button sterilization, manual wand

clean or UV function.

4.0L

Level III

305mm

Min water pressure 0.07MPa (dynamic pressure)

Max water pressure 0.74MPa

220V~, 50Hz

1100W

About 1600W

About 1.1m

About

705mm x 451mm x 526mm

About 46kg

1-35°C

1-40°C

Fast Press(Caution: Please don't knock hard, else the mechanical flush

switch may deform.)

* The description of water efficiency label marked on intelligent toilet: water efficiency label represents a compliance mark of the water efficiency grade etc. performance of intelligent toilet.

1303729-T01-G

Kohler Co.

Fig.#3

Fig.#4

PREPARATIONS BEFORE INSTALLATION

A.Hold the rim of the vitreous shell and take out the toilet.

B.When taking out the toilet from the carton box, please pay special attention to the bottom of the toilet to avoid

the tank assembly to drop out.

WARNING:Risk of personal injury and product damage! Please do not hold the rim of the bidet seat when

lifting the toilet. As the toilet is heavy, please seek for help if necessary.

Toilet

Tank Assy

Kohler Co.

1303729-T01-G

Fig.#5a

EPE Foam

Fig.#5b

Gasket Collar

Fig.#5c

C. Take out the tank.

a. Place an 800mm x 600mm cushion on the floor and then put the whole toilet on it.

NOTICE:Operate with care to avoid scratching the surface of the vitreous shell.

b. Take out the tank assembly from the vitreous shell and put it on the floor.

D. Place every part on the floor and ready for

installation.

Remove the EPE foam from the tank.

Remove the gasket and the collar.

Fig.#6

Actuation Switch

1303729-T01-G

Kohler Co.

Fig.#8

A. To Remove Existing Toilet

B. Roughing-In

Fig.#7

INSTALLATION

Turn off the water supply. Flush the toilet, and use a sponge to remove the remaining water from the tank and

bowl. Disconnect the supply shut-off valve (if present), and remove the old tank and bowl.

Remove old gasket from the floor and closet flange with a putty knife. Remove old T-bolts and discard them.

NOTICE:if a new toilet is not installed

immediately, temporarily stuff a rag in

the closet flange.

WARNING: Risk of electric shock.Connect only to circuits protected by Ground-Fault Circuit-Interrupters

(GFCI s) or Earth-Leakage Circuit-Breakers (ELCB s).

Keep bath and shower away from electrical parts (such as remote controller, receptacle, audio input appara-

tus and so on).

If the socket is wall-mounted , a GFCI or ELCB protected and water proof receptacle is required.

Follow the dimensional information exactly when installing a hardwire electrical supply.

DANGER:Risk of electric shock.Disconnect power before servicing.

NOTE.This product is designed for installation with the electrical supply and water pipeline

located through the wall.It is shown in the roughing-in.

Supply Stop

Floor Flange

T-Bolts

The wall location of the electrical supply and water

supply are interchangeable.

GFCI-Protected 10A Receptacle(water proof)

Closet Flange

Warning: before installation, please confirm floor and flange is connected by expansion bolt.

Kohler Co.

1303729-T01-G

C. Install the Electrical Service and Water Supply

D. Install the T-Bolts

Install the Electrical Service

Install the Water Service

Fig.#9

NOTE: This product is designed for installation with the electrical supply located through the wall. Both

types are illustrated. Refer to the dimensional information for your chosen installation.

NOTE:This product is designed for installation with the water supply located through the wall. Both types

are illustrated. Refer to the dimensional information for your chosen installation.

NOTE:A floor mounted water supply stop must be no higher than 70mm from the floor.

Install the water supply. If you are installing a floor supply, study the dimensional information illustrated

carefully.

Install two new 8mm (5/16") diameter T-bolts into the

floor flange.

Do not use white cement or high lime content cements

to install this toilet. The expansion of cement due to a

rise in temperature may make the toilet crack or cause

damage. Kohler is not responsible for any damage

caused by installation with the use of cement.

DANGER: Risk of electrical shock. For hardwire installations/through-floor electrical supply:

Connect only to a properly-grounded, dedicated

220V~, 10A, 50Hz circuit protected by a Class A

Ground-Fault Circuit-Interrupter (GFCI) or Earth- Leakage Circuit-Breaker (ELCB).

DANGER: Risk of electrical shock. For plug-in installations/wall-mounted electrical supply:

This product is designed only for installation with the electrical supply located through the wall ,

grounding-type receptacle which is protected by a Ground-Fault Circuit-Interrupter (GFCI). Do not

remove the grounding pin or use a grounding adapter.

DANGER: Risk of electric shock.Disconnect power before servicing.

Follow the dimensional information exactly when installing a hardwire electrical supply.

T-Bolts

Floor Flange

1303729-T01-G

Kohler Co.

fig.#11

fig.#10

E. Install the Wax Ring

F. Position the Tank

Place the wax ring in the putty ring located on the tank.

Mark the centerline on the floor.

Align the tank over the floor flange.

Lower the tank onto the floor flange. The T-bolts should align

with the mounting slots in the base of the tank.

Carefully align the tank on the centerline.

Position the tank on the T-bolts.

CAUTION: Risk of product damage.Do not push down on any part of the tank assembly other than the

cylinder. Damage may occur.

CAUTION: Risk of product damage.Do not rock or lift the tank after placement. The seal created by the

wax ring may be broken, resulting in leaking.

Position the loose end of the refill tube out the outlet ring.

Outlet Ring

Press here on cylinder.

Tank

Refill Tube

Floor Flange

T-Bolts

Centerlines

Kohler Co.

1303729-T01-G

Fig.#14

G. Secure the Tank

H. Connect the Water

I. Check the Waterline

CAUTION: Risk of product damage.Do not overtighten

the mounting nuts. Do not shorten the T-bolts.

Note:In case there is no floor flange, please fix the tank with the expansion

bolt kits. Specific installation steps are decided by the installer.

Turn on the water supply.

Use a flathead screwdriver to turn the manual switch counterclockwise to open the matorized valve.

Verify the inlet valve is set to the correct waterline. Adjust if needed.

To adjust the waterline, use a flathead screwdriver to gently turn the adjustment rod counterclockwise to lower and

clockwise to raise the waterline setting.

Return the manual switch into the locked position by using a

flathead screwdriver to turn it clockwise.

Stop the shut-off value.

Note:The waterline is a notch in the inside of the tank, marked with a label.

IMPORTANT!

Please use the water supply hose accompanying with new machine. The old hose assembly shall not be used again.

IMPORTANT! The valve will not operate if the valve is locked.

IMPORTANT! The water tank must be emptied after the

shut-off valve is locked.

Place a washer on each T-bolt.

Thread a nut onto each T-bolt.

Hand tighten the nuts.

Connect the water.

Open the shut-off valve.

Fig.#12

Fig.#13

Nut

Washer

T-Bolt

Base of

Tank Unit

Waterline

Adjust waterline

Unlock

Lock

1303729-T01-G

Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Toilette Handbücher

Kohler

Kohler Santa Rosa K-3811-33 Bedienungsanleitung

Kohler

Kohler K-6918 Montageanleitung

Kohler

Kohler REVIVAL K-14241 Bedienungsanleitung

Kohler

Kohler K-3489 Series Montageanleitung

Kohler

Kohler Sterling Windham 402015 Bedienungsanleitung

Kohler

Kohler K-3608 Montageanleitung

Kohler

Kohler WELLWORTH K-3432 Bedienungsanleitung

Kohler

Kohler K-10349 Bedienungsanleitung

Kohler

Kohler K-4406X Montageanleitung

Kohler

Kohler Revival K-3360 Montageanleitung

Kohler

Kohler FAMILY CARE K-23188T-NS Bedienungsanleitung

Kohler

Kohler K-3825 Montageanleitung

Kohler

Kohler OVE K-24719T-S2 Bedienungsanleitung

Kohler

Kohler ARCHER K-4440T Bedienungsanleitung

Kohler

Kohler WELLWORTH LITE K-3420 Bedienungsanleitung

Kohler

Kohler C3-325 Bedienungsanleitung

Kohler

Kohler SAN SOUCI CLASS FIVE K-21865T-S Bedienungsanleitung

Kohler

Kohler PATIO URINAL Bedienungsanleitung

Kohler

Kohler K-28119 Bedienungsanleitung

Kohler

Kohler K-11844 Montageanleitung

Kohler

Kohler K-3506 Montageanleitung

Kohler

Kohler ARCHER K-3614T Bedienungsanleitung

Kohler

Kohler K-18154 Bedienungsanleitung

Kohler

Kohler Highline K-4405 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung