Kohler SAN SOUCI K-21865T-HC Bedienungsanleitung

SAN SOUCI CLASS FIVE

INSTALLATION INSTRUCTIONS

3.3/4.8L VITREOUS CHINA SKIRTED INTEGRATED 1PC TOILET (W/O SEAT)

3.3/4.8 ( )

S-TRAP 305mm K-21865T-HC

S-TRAP 400mm K-20972T-HC

-1-

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

·-

ORDERING INFORMATION

SAN SOUCI (C3-150) Skirted 1PC

305mm W/O Seat ...............................................K-21865T-HC

ISAN SOUCI (C3-150) Skirted 1PC

400mm W/O Seat ..............................................K-20972T-HC

(C3-150)

305mm( )...............................................K-21865T-HC

(C3-150)

400m( )..................................................K-20972T-HC

2020

No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137

2 528137

8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 256410

8 256410

NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 110400

1 110400

POST CODE:

1364890-T01-B

-2-

NOTES

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 140mm (5-1/2") centers.

51mm (2") passageway.

Water depth from the rim is 160mm .

Ensure that the new drain has the correct roughing-in

dimension. This toilet has a 305mm/400mm roughing-in

dimension. .

Closet flange must be 305mm/400mm on-center from wall.

Carefully inspect the new fixture for any sign of damage.

For new construction, refer to the dimensions in

for locating the shut-off valve.

(5-1/2")

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112.19.2-2018).

This product complies with GB 25502-2017. Water

Efficiency Grade 1.

See Fig. #1

Fig. #1

and Fig. #4

140mm

51mm

160mm

305mm/400mm( 1)

305mm/400mm

ASME (A112.19.2-

2018)

GB 25502-2017 1

TOOLS AND MATERIALS REQUIRED (Not

supplied)

254mm (10") adjustable wrench

305mm (12") pipe wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Toilet gasket (wax seal)

Toilet T-bolts (2), 8mm (5/16") diameter

Toilet supply shut-off valve, 10mm(3/8 ) recommended

Hose Pipe

If the existing toilet does not have a supply shut-off

valve below the tank, install one before installing the new

toilet.

The stop valve and wax ring are not supplied.

NOTICE:

254mm

305mm

8mm T 2

10mm

WARNING: Risk of personal injury or product

damage

WARNING: Risk of external leakage

: Handle vitreous china products very carefully.

Vitreous china can break and chip if you overtighten

bolts and nuts.

. The fill valve

nut has been factory-tightened to design specifications.

If re-tightening is required, wrench tighten one turn

past finger tight .

1364890-T01-B

Unit: mm

Reference Value

K-21865T-HC

Finished Wall

Fig.#1

K-20972T-HC

Kohler reserves the right to change marked dimensions without prior notice.

Finished Wall

-3-

FRONT OF BOWL

OF OUTLET

698

140

417

619

200

160

395

305

400

OF OUTLET

698

140

395

305

1364890-T01-B

-4-

TO REMOVE EXISTING TOILET

Turn off the water supply. Flush the toilet, and use a sponge

to remove the remaining water from the tank and bowl.

Disconnect the supply shut-off valve (if present), and remove

the old tank and bowl.

()

INSTALLATION

Fig.#2

Remove the old gasket from the floor

and the closet flange with a putty knife.

Remove the old T-bolts and discard

them.

if the new toilet is not

installed immediately, temporarily stuff

a rag into the closet flange.

NOTICE:

NOTICE: Do not use white cement or high lime content

cements to install this toilet. The expansion of cement due to

a rise in temperature may make the toilet crack or cause

damage. Kohler is not responsible for any damage caused by

installation with the use of cement.

Closet Flange

67mm;

200mm

160

Fig.#3

TO INSTALL SUPPLY

SHUT-OFF VALVE

Install the supply shut-off valve so it is

200mm above the finished floor line,

and 160mm to the left of the closet

flange centerline.

The centerline of the supply shut-off

valve outlet should extend 67mm from

the finished wall. Install the supply

shut-off valve with the outlet vertical.

Supply Shut-Off Valve

Closet Flange

Centerline

160

305/400

200

TO INSTALL BOWL

Position the template and align with

drain hole.

Mark down the position of foot and 5

holes.

Fig.#4

Fig.#5

Drain Hole

3/8

10mm

Drill holes on ground with the drill of

10mm (3/8"), then insert anchor to

holes.

CAUTION: Please make sure there is

no water pipe or spool under the 5

holes to be drilled.

1364890-T01-B

-5-

Fig.#7

Firmly press the toilet gasket onto the

toilet outlet of plastic trap.

Wax ring type toilet gasket

should not be installed at temperatures

less than 21 C.

If you are using a toilet

gasket with an integral plastic sleeve,

make sure the gasket is positioned

with the sleeve facing away from the

toilet.

NOTE 1:

NOTE 2:

Install brackets.

Plastic Trap Outlet

Toilet Gasket

Fig.#8

Install plastic to ground and mounted

with 3 set of bolts (not supplied) firmly.

)

NOTE: Must use the toilet installation

gasket ring (not supplied) to seal the

area where the waste pipe contacts

the construction section to avoid

leakage.

(

)

Fig.#6

Fig.#9

Carefully align and lower the bowl.

Apply weight to the bowl rim to let the

outlet insert into plastic trap.

Outlet

Plastic Trap

Fig.#10

Carefully thread the screws into the

brackets, until toilet is secure.

Alternately tighten left and right sides

to prevent pulling the toilet off center.

Install cap to cover screw.

Do not overtighten.

Cap Screw

Bushing

1364890-T01-B

-6-

Fig.#11

Apply caulk around base.

TO CONNECT WATER

SUPPLY

* Flexible hose (not provided) are

recommended to connect the supply

line to the fill valve. If you use a rigid

connection(not provided), take care

not to apply side forces to the bottom

of the fill valve. Be sure the rigid

connection must be fit with supply line

completely to prevent damage shank

by forced connection.

()

Supply Shank*

Supply Shut-Off Valve

Fig.#12

IMPORTANT:

Make certain the top is turned to the locked

position. Valve may not turn on if top is not fully in the

locked position.

Before turning on the supply valve for the first

time, follow the steps below to clear sand, debris and rust

from the system:

Make sure water sure water supply is off. Remove valve END

by rotating it 1/8 turn counterclockwise.

While holding a container over the uncapped VALVE to

prevent splashing, turn water supply on and off a few times.

Leave water supply off.

Replace END by engaging lugs and rotating 1/8 turn

clockwise.

Turn on water supply. Check that water level is at the marked

water line.

1/8

Install the tank lid and the seat. Use the supplied hardware

pack for seat. Periodically check for leaks for several days

following the installation.

Fig.#13

1364890-T01-B

-7-

SYMPTOMS CORRECTIVE ACTION

1. Poor Flush A. Adjust the tank water level to match the waterline.

B. Fully open the water supply shut-off valve.

C. Clear obstructions from the trapway, jet, or bowl rim holes.

D. Clear obstructions from the waste line.

A. Adjust the chain for proper slack so the seal is not held off the flush valve seat.

B. Clean or replace the seal if it is worn, dirty, or misaligned with the flush valve seat, or

if the flush valve seat is damaged. Replace the flush valve seal or flush valve.

C. Clean the fill valve seat/seat washer of debris, or replace the piston/seat washer

assembly.

D. Remove the tank and tighten the flush valve nut if flush valve gasket is leaking. Do

not overtighten. If leakage continues, replace the gasket.

E. Adjust the tank water level if it is too high.

2. No Flush

IMPORTANT: Use only genuine Kohler parts as shown to avoid property damage.

4. Tank takes excessive time to fill.

5. There is excessive noise when the

tank is filling.

3. The fill valve turns on/off by itself

without the toilet being flushed, or it

runs allowing water to enter the tank.

A. Reconnect the chain to the trip lever or flush valve.

B. Adjust the chain assembly to remove excessive slack.

A. Fully open the water supply shut-off valve.

B. Clean the valve inlet, valve head, or supply line. Flush the lines.

A. Partially close the water supply shut-off valve if the water pressure to the toilet is too

high. Check the toilet performance following any such adjustment.

B. Remove dirt or obstructions from the valve head. Flush the lines.

1. A.

C. /

3. /

Fig.#14

FILL FLOAT WITH

BALLAST

Test flush the toilet.

Periodically check all connections for

leaks for several days following

installation.

Set the tank cover in place on the tank.

1364890-T01-B

-8-

()

CONSUMER RESPONSIBILITIES

If you live in a hard water area, make certain that the holes in

the toilet rim are kept clean to ensure proper bowl flushing.

Toilet bowl cleaners should be used at least once a week.

Use a long-handled brush to clean the rim holes, and to clean

as far into the trap as possible to prevent mineral deposits

from forming.

Most toilet bowl cleaners are not harmful to the vitreous china

surface of the toilet bowl. Please follow the bowl cleaner

manufacturer's instructions carefully.

Do not use abrasive cleaners or solvents.

Do not use in-tank cleaners. Products containing

chlorine (calcium hypochlorite) can seriously damage

fittings in the tank. This damage can cause leakage

and property damage.

Kohler Company shall not be responsible or liable for any

damage to these tank fittings caused by the use of cleaners

containing chlorine (calcium hypochlorite).

WARNING: Risk of property or product damage.

CAUTION: Please do not use hard materials (like

scouring pad) to clean product surface, especially the

product logo.

CAUTION: Don t use any cement while installing

the toilet.

WARNING: Risk of product damage.

Heat expansion of the toilet may damage

the feet of the toilet. Kohler will not be responsible for

any damage because of using cement.

Do not throw into the toilet what is easy to block it,

such as newspaper, paper pilch, sanitary towel.

Do not bump the vitreous china with great force to

prevent it from damaging and leaking.

Do not use the product in the water below 0 C.

1364890-T01-B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Toilette Handbücher

Kohler

Kohler KARING 2.0 K-77780T-0 Bedienungsanleitung

Kohler

Kohler K-25839T-NSHC Bedienungsanleitung

Kohler

Kohler 231880 Bedienungsanleitung

Kohler

Kohler K-18154 Bedienungsanleitung

Kohler

Kohler K-24097X Montageanleitung

Kohler

Kohler Adair K-9338T Bedienungsanleitung

Kohler

Kohler NUMI 2.0 Montageanleitung

Kohler

Kohler K-28413H Montageanleitung

Kohler

Kohler K-3519 Montageanleitung

Kohler

Kohler Irvine E915 Bedienungsanleitung

Kohler

Kohler ADAIR K-75925T Bedienungsanleitung

Kohler

Kohler K-3998M Montageanleitung

Kohler

Kohler ODEON K-8711T-2 Bedienungsanleitung

Kohler

Kohler PANACHE K-18182T-2 Bedienungsanleitung

Kohler

Kohler Persuade Circ K-3753 Benutzerhandbuch

Kohler

Kohler K-17757 Bedienungsanleitung

Kohler

Kohler ESCALE K-32771T-NS Bedienungsanleitung

Kohler

Kohler Innate K-8340TW-2EXSG-0 Montageanleitung

Kohler

Kohler STERLING 402040 Montageanleitung

Kohler

Kohler C3-420 Bedienungsanleitung

Kohler

Kohler C3-130 Montageanleitung

Kohler

Kohler K-3417 Fleur Betriebsanleitung

Kohler

Kohler Intelligent Toilet Montageanleitung

Kohler

Kohler K-18751-0 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung