Komatsu PC200LC-8 Handbuch

CEAM007103

Operation&Maintenance

Manual

PC200LC-8

PC220LC-8

HYDRAULIC EXCAVATOR

SERIAL NUMBERS PC200LC-8 A88001and up

PC220LC-8 A88001and up

ENGINE 6D107E-1

This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in

accordance with written authorization from Komatsu America Corp.

It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make

changes or improvements at any time without incurring any obligation to install such changes on products sold

previously.

Due to this continuous program of research and development, revisions may be made to this publication. It is

recommended that customers contact their distributor for information on the latest revision.

Printed in U.S.A.

Komatsu America Corp.

March 2016

California

Proposition 65 Warning

This machine may contain mercury in two areas:

a.) The display monitor contains mercury if it has a mercury

label attached.

b.) Optional HID bulbs contain mercury (if the machine is so

equipped).

There is no risk of exposure unless the bulbs are broken.

However, the monitor and/or lamps must be reused, recycled

or properly disposed of in accordance with Local, State and

Federal Laws at the end of their useful lives.

Find manuals at https://best-manuals.com

0-1

INTRODUCTION 0

PC200/220LC-8

Find manuals at https://best-manuals.com

INTRODUCTION

0-2 PC200/220LC-8

FORWARD

This manual provides rules and guidelines which will help you use this machine safely and effectively. The precautions in this

manual must be followed at all times when performing operation and maintenance. Most accidents are caused by the failure to

follow fundamental safety rules for the operation and maintenance of machines. Accidents can be prevented by knowing

beforehand conditions that may cause a hazard when performing operation and maintenance.

Storage location for the Operation and Maintenance Manual:

Magazine box on the left side of the operator's seat.

Before beginning operation or maintenance, operators and maintenance personnel must always observe

the following points.

●Read this manual thoroughly and understand its contents fully.

●Read the safety messages and safety labels given in this manual carefully so that they are understood

fully.

●Keep this manual at the storage location for the Operation and Maintenance Manual given below so

that all personnel involved in working on the machine can consult it periodically.

●In case this manual is lost or damaged, immediately contact Komatsu or your Komatsu distributor to

obtain a new copy.

●When you sell the machine, make sure that this manual is provided to the new owner together with the

machine.

●In this manual, measurements are expressed in international standard units (SI). For the reference

purpose, weight units used in the past are also displayed in ( ).

Find manuals at https://best-manuals.com

INTRODUCTION

PC200/220LC-8 0-3

SAFETY INFORMATION

Most accidents are caused by the failure to follow fundamental safety rules for the operation and maintenance of machines. To

avoid accidents, read, understand and follow all precautions and warnings in this manual and on the machine before

performing maintenance and machine operations.

The following signal words are used to inform you that there is a potentially hazardous situation that may lead to personal

injury or damage. In this manual and on machine labels, different signal words are used to express the potential level of

hazard.

Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury. This signal word is to be limited to most extreme situations.

Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury. It may also be used to alert against unsafe practices.

Remark

This word is used for precautions that must be taken to avoid actions, which could shorten the life of the

machine.

Safety precautions are described in SAFETY section 1.

KOMATSU AMERICA CORP. cannot predict every circumstance that might involve a potential hazard in operation and

maintenance. Therefore the safety message in this manual and on the machine may not include all possible safety precautions.

If any procedures or actions not specifically recommended or allowed in this manual are used, you must be sure that you and

others can do such procedures and actions safely and without damaging the machine. If you are unsure about the safety of

some procedures, contact your local distributor or KOMATSU AMERICA CORP.

Find manuals at https://best-manuals.com

INTRODUCTION

0-4 PC200/220LC-8

•Safety labels

Safety labels are affixed to the machine to inform the operator or maintenance worker on the spot when carrying out

operation or maintenance of the machine that may involve hazard.

This machine uses "Safety labels using words" and "Safety labels using pictograms" to indicate safety procedures.

Example of safety label using words

Safety labels using pictogram

Safety pictograms use a picture to express a level of hazardous

condition equivalent to the signal word. These safety pictograms use

pictures in order to let the operator or maintenance worker

understand the level and type of hazardous condition at all times.

Safety pictograms show the type of hazardous condition at the top or

left side, and the method of avoiding the hazardous condition at the

bottom or right side. In addition, the type of hazardous condition is

displayed inside a triangle and the method of avoiding the hazardous

condition is shown inside a circle.

Komatsu cannot predict every circumstance that might involve a potential hazard in operation and maintenance.

Therefore, the safety messages in this manual and on the machine may not include all possible safety precautions.

If any procedures or actions not specifically recommended or allowed in this manual are used, it is your responsibility to

take the necessary steps to ensure safety.

In no event should you engage in prohibited uses or actions described in this manual.

The explanations, values, and illustrations in this manual were prepared based on the latest information available at that

time. Continuing improvements in the design of this machine can lead to changes in detail which may not be reflected in

this manual. Consult Komatsu or your Komatsu distributor for the latest available information of your machine or for

questions regarding information in this manual.

The numbers in illustrations correspond to the numbers in (_) in the text. (For example: 1 -> (1))

Find manuals at https://best-manuals.com

INTRODUCTION

PC200/220LC-8 0-5

INTRODUCTION

This Komatsu machine is designed to be used mainly for the following work:

•Digging work

•Leveling work

•Ditching work

•Loading work

•Demolition work

See “RECOMMENDED APPLICATIONS” on page 2-169 for further details.

Directions of Machine

In this manual, the terms front, rear, left, and right refer to the travel direction as seen from the operator's seat when the

operator's seat is facing the front and the sprocket is at the rear of the machine.

Visibility from Operator's Seat

This machine complies with the visibility standard (ISO 5006).

This machine maintains a close visibility of a height of 1.5 m (4.9 ft) at a point 1 m (3.2 ft) away from the outside surface of

the machine, and a visibility for a circumference of 12 m (39.3 ft).

(A) Front (C) Left (E) Operator’s Seat

(B) Rear (D) Right (F) Sprocket

Find manuals at https://best-manuals.com

INTRODUCTION

0-6 PC200/220LC-8

Breaking-in the New Machine

Remark

Your Komatsu machine has been thoroughly adjusted and tested before shipment from the factory. However,

operating the machine under full load before breaking the machine in can adversely affect the performance

and shorten the machine life.

Be sure to break in the machine for the initial 100 hours (as indicated on the service meter).

Make sure that you fully understand the content of this manual, and pay careful attention to the following points when

breaking in the machine.

•Run the engine at idle for 15 seconds after starting it. During this time, do not operate the control levers or fuel control

dial.

•Idle the engine for five minutes after starting it up.

•Avoid operation with heavy loads or at high speeds.

•Immediately after starting the engine, avoid sudden starts, sudden acceleration, unnecessary sudden stops, and sudden

changes in direction.

Find manuals at https://best-manuals.com

INTRODUCTION

PC200/220LC-8 0-7

Product Information

When requesting service or ordering replacement parts, please inform your Komatsu distributor of the following items.

Product Identification Number (Pin) / Machine Serial No. Plate

On the bottom right of the operator's cab

The design of the nameplate differs according to the territory.

EPA* Regulations, Engine Number Plate

On the upper side of the engine cylinder head cover.

*EPA: Environmental Protection Agency, U.S.A.

Find manuals at https://best-manuals.com

INTRODUCTION

0-8 PC200/220LC-8

Service Meter Location

On top of the machine monitor.

Your Machine Serial Numbers and Distributor

Machine serial No.

Engine serial No.

Product identification number (PIN)

Distributor name

Address

Service Personnel

Phone/Fax

Find manuals at https://best-manuals.com

Andere Handbücher für PC200LC-8

Dieses Handbuch passt für folgende Modelle

Andere Komatsu Bagger Handbücher

Komatsu

Komatsu PC170LC-11 Installationsanleitung

Komatsu

Komatsu PC600LC-7 Backhoe Bedienungsanleitung

Komatsu

Komatsu PC290LC-11 Installationsanleitung

Komatsu

Komatsu PW160-7K Series Bedienungsanleitung

Komatsu

Komatsu PC400LC-8 Handbuch

Komatsu

Komatsu D85EX_15R - D85PX-15R Benutzerhandbuch

Komatsu

Komatsu PC78US-10 Installationsanleitung

Komatsu

Komatsu PC210LC-11 Installationsanleitung

Komatsu

Komatsu PC238USLC-11 Installationsanleitung

Komatsu

Komatsu GD705A-4 Installationsanleitung

Komatsu

Komatsu Galeo PC1250-7 Backhoe Handbuch

Komatsu

Komatsu HB215LC-2 Installationsanleitung

Komatsu

Komatsu PC500LC-10R Installationsanleitung

Komatsu

Komatsu PC240LC-11 Installationsanleitung

Komatsu

Komatsu PC1250 -8 Installationsanleitung

Komatsu

Komatsu PC220-8 Bedienungsanleitung

Komatsu

Komatsu PC210LCI-11 Installationsanleitung

Komatsu

Komatsu PC600LC-8 BACKHOE Bedienungsanleitung

Komatsu

Komatsu D155AX-7 Installationsanleitung

Komatsu

Komatsu PC78US-6 Handbuch

Komatsu

Komatsu WA900-3E0 Installationsanleitung

Komatsu

Komatsu PC210LC-6K Handbuch

Komatsu

Komatsu GALEO PC1250-8 Handbuch

Komatsu

Komatsu PC160LC -7E0 Installationsanleitung

Beliebte Bagger Handbücher anderer Marken

Hyundai

Hyundai Robex 210LC-9 Bedienungsanleitung

Hitachi

Hitachi Zaxis 110 Zaxis 125US Gebrauchsanweisung

sennebogen

sennebogen 830 E Bedienungsanleitung

Topcon

Topcon X-63 Gebrauchs- und Pflegehandbuch

Hitachi

Hitachi ZX27U-2 Bedienungsanleitung

jcb

jcb 15c-1 Bedienungsanleitung

Case

Case CX290B Bedienungsanleitung

SUNWARD

SUNWARD SWE155F Handbuch

CNH

CNH CX16B Bedienungsanleitung

Super Products

Super Products MUD DOG 700 Bedienungsanleitung

New Holland

New Holland E57C Bedienungsanleitung

Hyundai

Hyundai Robex 160LC-9 Bedienungsanleitung

Doosan

Doosan DX180LC Installationsanleitung

Hyundai

Hyundai HW65AH Bedienungsanleitung

mecalac

mecalac 14 MBX Bedienungsanleitung

CASE CONSTRUCTION

CASE CONSTRUCTION CX350C Bedienungsanleitung

Hyundai

Hyundai Robex 140LC-9 Bedienungsanleitung

Case

Case CX50B Bedienungsanleitung