KONEL DL Series Bedienungsanleitung

The second alarm

hysteresis: same as HY1.

Input Channel Selection:

Chosen from "IN1～IN3"

The first alarm mode:

H：High；L：Low

The first alarm value

setting

The second alarm mode:

same as Ad1.

The first alarm hysteresis.

For example, if Ad1=H,

AL1=50, HY1=5, when

measuring value≥50(AL1),

alarm is actived;when it

≤45 (AL1-HY1), alarm is

deactived.

The second alarm value

setting: same as AL1

Measuring status

operation setting

① The second row LED is defaulted to display range and input channel alternately after

power on, press ( ) to display range only, press ( ) to returns to default display

② In the measuring status, press SET >3S to enter setting menu.

③ When modifying setting value, press / to change value; press ( ) key to shift decimal

point; after modifying, press SET key to confirm and enter next menu. After setting,press SET

key more than 3S to exit menu; if there is no operation for a long time, it will exit automatically.

V. Operations

AL1: Alarm 1#

AL2:Alarm 2#

III. Panel Illustration

AC/DC 100～240V 50Hz/60Hz DC 24V(Need to be ordered)

0.001-9999 float decimal point display

±0.5%F.S ±2digits(For AC signal frequency under 100Hz）

4～20mA load capacity≤600Ω, accuracy:±0.5%F.S

AC 250V/3A or DC 30V/5A

Between power supply connector and other connectors, relay output

connectors and other connectors, AC 1800V leakage current 0.5mA,

60S; Between input signal connectors and low voltage signal output

connectors, DC 600V leakage current 0.5mA,60S

Temperature：0-50℃Humidity：≤85%RH

5 times/S

RS485 communication interface,Modbus RTU Protocol

≥100MΩ/500V DC

Power Supply

Display range

Accuracy

Analog output

Relay capacity

Dielectric Strength

Communication

Insulation Impedance

Working environment

Sampling rate

Default channel

and range

Analog outputInput channel and Range

Range

Version code

A：AC/DC current V：AC/DC voltage

10：No RS485 18：With RS485

B：One alarm C：Two alarms

A：No alarm R：Relay alarm

DL8A series voltage/ampere meter

8: 48H*96W*100L 9: 96H*96W*100L

Blank: No analogue output

I：4~20mA analogue output

An operation that does not comply with the instruction may lead to product damage.

An accident may happen if the operation does not comply with the instruction.

Warning

Notice

※ Please comply with the below important points.

An accident danger may happen in a special condition.

The instruction of the symbol in the manual is as below.

Please read the manual carefully before you use the meter.

For your safe, please read the below content carefully before you use the meter!

.This product cannot be used outdoors. Otherwise the working life of the product will become

shorter, or an electric shock accident may happen.

2.When you connect wire to the power input connectors or signal input connectors, the

moment of the No.20 AWG (0.50 mm） screw tweaked to the connector is 0.74n.m - 0.9n.m.

Otherwise the connectors may be damaged or get fire.

3.Please comply with the rated specification. Otherwise it may cause electric shock or fire, and

damage the product.

4.Do not use water or oil base cleaner to clean the product. Otherwise it may cause electric

shock or fire and damage the product.

This product should be avoid working under the circumstance that is flammable, explosive, moist,

under sunshine, heat radiation and vibration. Otherwise it may cause explosion.

In this unit it must not have dust or deposit, otherwise it may cause fire or mechanical malfunction.

Do not use gasoline, chemical solvent to clean the cover of the product because such solvent can

damage it. Please use some soft cloth with water or alcohol to clean the plastic cover.

⊙Accuracy: 0.5%F.S.

⊙AC/DC universal (for AC signal it measures true value).

⊙Different input channel has different range, wide measuring range.

⊙Two Hi/Lo setting alarm output.

⊙With analog output 4-20mA.

⊙RS485 communication interface, Modbus RTU protocol.

Features:

DL8A/DL9A Voltage/Ampere Meter User Manual

DL Series

Safe Caution

Power

supply

All

LED

are

Measuring

Status

Power On

II. Technical Specification

①When you use the meter, please pay attention that input channel should correspond to range,

otherwise, the meter will be malfunction. ②Input signal < 1.2 times of range. ③When measuring

AC signal, aviliable for 0～200Hz. When frequency is higher than 100Hz, the measuring accuracy

is ±1%FS.

Model Alarm

2 alarm

4-20mA

RS485

Commu-

nication

IN3:600V

IN1:5A

IN2:1000mA

Decrease key

Increase key

Shift key

SET: Parameter select/confirm key

Displaying parameter

set value/input code

Displaying measuring value/parameter code

A(mA): Current indication lamp

V: Voltage indication lamp

I. Code Illustration

1.A safty protection equipment must be installed or please contact with us for the relative

information if the product is used under the circumstance such as nuclear control, medical

treatment equipment, automobile, train, airplane, aviation and equipment etc.. Otherwise, it

may cause serious loss, fire or person injury.

A panel must be installed, otherwise it may cause creepage (leakage).

Do not touch wire connectors when the power is on, otherwise you may get an electric shock.

4.Do not dismantle or modify the product. If you have to do so, please contact with us first.

Otherwise it may cause electric shock and fire.

5.Please check the connection number while you connect the power supply wire or input signal,

otherwise it may cause fire.

For range A1000, the default

one is IN1; for range A1, the

default one is IN2；for range

V600，the default one is IN3

90% of measuring range

10% of measuring range

maximum of the range

minimum of the range

001

9.6

000

1.000

0.000

INP

Ad1

AL1

Ad2

AL2

Add

bAd

LCK

Hy1

Hy2

IN1～IN3

H or L

-1999～9999

0～9999

0～255

4.8 or 9.6

Factory value IndicationNo. Paremeter code Setting range

AL,HY,Ct,PS,

rH,rL have the

sameunit as

the Range.

Warning

Caution

Lock key

Lock=000,read and write

Lock=010,read only

Current Transforming: it is only

for 5A range or 75mV spliter

current input. If its value is set

as the the ratio of external CT

or spliter, the actual range

should be CT*5. For other

situation, CT is set as 1.

Amendment value,displaying

value=measured value +PS,

factory setting: PS=0

Communic:ation baud rate:

4.8kbps、9.6kbps for option.

Add：Meter communication

address

Analog output low limit setting:

when measured value = rL set

value, the corresponding

analog output is 4mA

Analog output high limit

setting:when measured value=

rH set value,the corresponding

analog output is 20mA.

KKDL8A-C01E-A/1-20190723

Analog output low limit value rL

2nd loop alarm hysteresis HY2

1st loop alarm hysteresis HY12

12345678

1 2 3 5

1 2 3 456 7 9 10 11 13128

Meter

ADD

Function

code

Meter ADD

Meter

ADD

Function

code

Function code

Start

ADD

High

bit

Start

ADD

Low

bit

Data

byte

length

high bit

Data

byte

length

low bit

CRC code

low bit

CRC code

high bit

0x01

0x01 0x10

0x01 0x10 0x00 0x01 0x00 0x02 0x10 0x08

0x00 0x01 0x00 0x04 0x00 0x00 0x03 0xE8 0x32 0xDD0x02

0x83 0x02 0xC2 0xC1

Slave normal answer (write multi-register)

Slave abnormal answer(Read multi-register)

Data

1 high

bit

Data

1 low

bit

Data

2 high

bit

Data

2 low

bit

CRC

code

low

bit

CRC

code

high

bit

CRC code low bit CRC code high bitError code

1 2 3 54

Meter ADD Function code

0x01

0x0000

0x0002

0x0004

0x0006

0x0008

0x000A

0x000C

0x000E

0x0010

0x90 0x02 0xCD 0xC1

Slave abnormal answer (write multi-register)

CRC code low bit CRC code high bitError code

2. Write multi-register

For example: Host write HY1 (1st alarm value hysteresis 1.0)

ADD code of HY1 is 0x0001， because HY1（4 byte）， seizes 2 data registers. The

hexadecimal memory code of decimal floating point number 1.0 *1000=1000 is 0x000003E8.

Host request (write multi-register)

Data

byte

length

Start ADD

high 8 bit

Start ADD

low 8 bit

Data byte

length high bit

Data byte

length low bit

Data location error response: (For example:Host request the ADD index is 0x0050)

Address Mapping Table of Meter Parameters

No ADD

mapping Variable name Data

Length Range Read/

write

Rate Remark

1st loop alarm value AL1

2nd loop alarm value AL2

Coefficient Ct

Analog output high limit value rH

Amendment value PS

-1999~9999

0~9999

-1999~9999

R/W0.001

0.001

R/W

Reserve

0x001F

0x0020

0x0021

0x0022

0x0023

1st loop alarm type Ad1

2nd loop alarm type Ad2

Alarm status indication

Baud rate

Meter address Add

Meter name

0~1

0~3

0~1

0x255

R/W

10xD1 R

Note ①

Note ③

Note ②

R: read only; R/W: read/write.

Note ①：alarm type

High limit alarm Communication value

Communication value

Low limit alarm Communication value

H 1 L 0

9.6

4.8

Note ②: baud rate

Menu display

Note ③: alarm status indiction

D7 D6 D5 D4 D3 D2 D1 D0

AL2 AL1

Abnormal answer: (For example: host request function code 0x03）

VIII. Communication

This meter using Modbus RTU communication protocol, and it can run RS485 half-duplex

communication. Read function code is 0x03, write function code is 0x10, 16-bit CRC checking

is applied. The meter don’t feedback error message. The communication data type is 32 bit

integer data, true code stands for positive number, complemental code stands for negative

number, data rate is 0.001；for example, if the meter data received by host is 5000, then meter

data * rate = original data (5000*0.001=5.000). Therefore, when host writes meter, the data

should multiply by rate 1000 before it is sent to the meter.

Data Frame format：

Start bit Data bit Stop bit Check bit

NO181

Handling of abnormal communication：

If there is abnormal response put the function code on the top position 1. For example:

Host request the function code 0x03,and the response function

code from slave should be 0x83.

Error type code：

0x02---Data location error：the request data location from host computer exceeds the range of

the meter.

0x03---Data value error：the data value sent by host computer exceeds the data range of the

meter.

CRC check error, function code error, don’t return value.

1. Read Multiple Registers

For example: The host computer read AL1（1st alarm value 5.0）

Address code of AL1 is 0x0000，32bit（4 byte），seizes 2 data registers; hexadecimal

memory code of 5.0*1000=5000 is 0x00001388.

Host request（read multi-register）

Meter

Add

Function

Code

Meter

Add

Function

Code

0x01 0x03

Slave normal answer(Read multi-register)

0x01

0x03

Data byte

number

0x04

Data 1

high bit

0x00

Data 1

low bit

0x00

0x13

Data 2

high bit

7 98

0x88 0xF7 0x65

Data 2

low bit

CRC code

low bit

CRC code

high bit

1、It is suggested that the meter gets on power for 15 minutes before measuring.

2、Working environment is 0～50℃，humidity below 85%RH.

3、The calibration interval for this meter is one year.

4、Please keep the meter from shaking and shocking. Don’t place the meter in the

environment full of excess dust and hazard chemicals and gas.

5、If the meter is not used for long time, please get on power every 3 months, each time

not less than 4 hours.

6、To be stored in the environment at 0～50℃, humidity below 60%RH, no direct sunshine.

The meter should not contact with organic solvent or oil.

VI. Notice for use and storage

Front Side Mounting

VII. Mounting dimension

DL8A voltage input DL8A current input

DL9A voltage input DL9A current input

0x001E

2Read measured value 0~9999 R

Start address

high bit

0x00

Start address

low bit

0x00

Data byte

length high bit

0x00

678

Data byte

length low bit

CRC code

low bit

CRC code

high bit

0x02 0xC4 0x0B

16 digits CRC check code acquisition program

V. Connection drawing

Note:please subject to the diagram on the product if any changes.

Dieses Handbuch passt für folgende Modelle

Andere KONEL Messgerät Handbücher

KONEL

KONEL BM500A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung