Konica Minolta MULTI GLOSS 268 Bedienungsanleitung

Instruction Manual

Betriebsanleitung

Mode d´emploi

MULTI GLOSS 268

UNI GLOSS 60

MULTI GLOSS 268A

UNI GLOSS 60A

UNI GLOSS 60CT

UNI GLOSS 60S

Instruction Manual

Patent pending 260 023 933 E 1609

MULTI GLOSS 268A

UNI GLOSS 60A

UNI GLOSS 60CT

UNI GLOSS 60S

Table of content

1. Safety Symbols ......................................................................................6

2. Safety Precautions .................................................................................7

3. Notes on Use ...........................................................................................8

4. System description .............................................................................. 13

5. Power supply........................................................................................ 14

5.1 Power supply battery-operated ............................................................ 14

5.2 Changing the battery ............................................................................. 15

5.3 External power supply ........................................................................... 15

6. Controls ................................................................................................. 16

7. Getting started ......................................................................................18

7.1 Turning on the unit and measuring ....................................................... 18

7.2 Navigation ............................................................................................... 19

7.3 Change names/numbers ....................................................................... 20

7.4 Overview of main menu ......................................................................... 21

8. Calibrate ............................................................................................... 22

8.1 Autodiagnosis ........................................................................................ 22

8.2 Calibrate ................................................................................................. 23

8.2.1 Gloss ........................................................................................... 23

8.2.2 Change cal.values ....................................................................... 24

8.2.3 Status ........................................................................................... 25

8.2.4 Scale Gloss ................................................................................. 25

8.3 Calibrating standards ............................................................................ 26

8.4 Checking standard ................................................................................ 26

9. Measurement techniques .................................................................... 27

9.1 Paints and varnishes, plastics and similar materials ......................... 27

9.2 Anodized aluminum and other metal surfaces .................................... 28

10. Measurement Modes ........................................................................... 29

10.1 Sample mode ......................................................................................... 29

Table of content

10.2 Statistics ................................................................................................ 30

10.2.1 Number of measurements.......................................................... 31

10.2.2 Display ......................................................................................... 31

10.2.3 Exit block ...................................................................................... 33

10.2.4 Delete block ................................................................................. 33

10.2.5 Delete measurement .................................................................. 33

10.3 Continuous ............................................................................................. 34

10.4 Basic mode ............................................................................................ 35

11 Geometry .............................................................................................. 36

11.1 Geometry selection ............................................................................... 36

12. Memory ................................................................................................. 37

12.1 Memory................................................................................................... 37

12.2 Select memory....................................................................................... 37

12.3 Create memory ...................................................................................... 38

12.4 Delete memory....................................................................................... 38

12.5 Display memory ..................................................................................... 38

13. Difference measurement and Pass/Fail ............................................ 40

13.1 Difference ............................................................................................... 40

13.2 Measure standard ................................................................................. 40

13.3 Select standard ..................................................................................... 41

13.4 Create standard ..................................................................................... 42

Define standard .............................................................................................. 42

13.5 Change standard ................................................................................... 43

13.6 Delete standard ..................................................................................... 43

14. Setup ..................................................................................................... 44

14.2 Date/Time ............................................................................................... 44

14.3 Beeper .................................................................................................... 44

14.4 Display time ............................................................................................ 44

14.5 Language ................................................................................................ 45

14.6 Info .......................................................................................................... 45

15. Interface ................................................................................................ 46

16. Standards .............................................................................................. 47

17. Specifications ....................................................................................... 48

Table of content

18. Accessories ........................................................................................... 49

19. Errors and warning messages ............................................................ 50

20. Cleaning and maintenance ................................................................ 52

21. Copyright .............................................................................................. 53

1. Safety Symbols

The following symbols are used in this manual and

the instrument to prevent accidents which may

occur as a result of incorrect use of the instrument.

• Denotes a sentence regarding a safety warning

or note. Read the sentence carefully to ensure

safe and correct use.

• Denotes a prohibited operation. The operation

must never been performed

• Denotes a prohibited operation. Never

disassemble the instrument.

• This symbol indicates direct current (DC).

Notes on this manual

• Copying or reproduction of all or any part of the

contents of this manual without permission of the

manufacturer is strictly prohibited.

• The contents of this manual are subject to

change without prior notice.

• Every effort has been made in the preparation of

this manual to ensure the accuracy of its

contents. However, should you have any

questions or find any errors, please contact the

store where you purchased the instrument.

• The manufacturer will not accept any

responsibility for consequences arising from the

use of the instrument.

Safety Symbols

2. Safety Precautions

To ensure correct use of this instrument, read the following points carefully and

adhere to them. After you have read this manual, keep it in a safe place where

it can be referred to anytime a question arises. If you pass this instrument to

somebody else, make sure to include these instructions.

Safety Precautions

Do not use the instrument in

places where flammable or

combustible gases (gasoline

etc.) are present. Doing so may cause fire.

Do not disassemble or modify

the instrument or the Power

supply. Doing so may cause a

fire or electric shock.

Take special care not to allow

liquid or metal objects to enter

the instrument. Doing so may

cause a fire or electric shock. Should liquid

or metal objects enter the instrument,

disconnect the Power supply from the AC

outlet immediately, and contact the store

where you purchased the instrument.

The instrument should not be

operate if it is damaged, or if

smoke or odd smells occur.

Doing so may result in a fire. In such

situations, remove the battery and/or

immediately disconnect the USB interface

cable, and contact the company where you

purchased the instrument.

CAUTION (Failure to adhere to the following points may result in injury

or in damage to the instrument or other property)

Do not use batteries other

than those specified. When

installing batteries in the

instrument, make sure that they are correctly

oriented according to the (+) and (-) marks.

Failure to adhere to these instructions may

cause batteries to explode or leakage of

electrolytes, resulting in fire, injury or air

pollution.

Only devices that meet the

requirements for low-voltage

safety can be connected to the

USB interface.

WARNING (Failure to adhere to the following points

may result in death or serious injury.)

Do not dispose of batteries in

fire, short the terminals, apply

heat to them, or disassemble

them. Also, do not recharge them. Doing so

may cause explosion or heat generation,

resulting in fire or injury.

Do not touch the battery with wet

hands. Doing so may cause

electric shock.

Notes on Use

3. Notes on Use

• The measurement unit consists of sensitive

precision optical and electronic parts.

Do not drop it. Protect it from being bumped or

jostled.

• Do not hold the unit by the measurement

aperture. You should not allow any foreign

objects to get into this opening.

• Do not expose the unit to direct sunlight for

extended periods of time. Do not store it in a hot

or dusty environment. The case that comes with

the unit offers the best protection when the unit

is being stored.

• Avoid prolonged high relative humidity and do not

allow condensation to form.

• Protect the measuring unit from moisture,

chemicals and corrosive vapors.

• The holder and the unit housing are resistant to a

number of solvents. However, we cannot

guarantee resistance to all chemicals. You

should therefore use a soft, moist cloth for

cleaning. For clean excessive dirt and dust, use

ethanol or cleaning alcohol.

Do not use any acetone!

• If you will not be using the measuring unit for an

extended period of time, remove the battery to

prevent it from leaking in the unit and thus

potentially causing damage.

Notes on Use

• Do not replace the internal backup battery

yourself. Contact the nearest authorized service

facility to replace the backup battery.

• If the instrument is subjected to strong static

electricity, the display may become blank. If this

occurs, wait for the power to be automatically

switched off, and then switch the power on

again.

• Do not perform any repairs on the unit yourself.

The unit must be opened by trained professions

only. Please contact our customer service

department in such cases.

• Do not use accessories other than those

specified by KONICA MINOLTA INC.

• Pollution degree 2: Use it in areas where there is

no metal dust and no possibility of condensation.

• Do not use at altitudes of higher than 2000m.

Additional information on use:

• Make sure that the instrument, accessories and

used battery are either disposed of or recycled

correctly in accordance with local laws and

regulations.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Konica Minolta Messgerät Handbücher

Konica Minolta

Konica Minolta VIVID 9i/VI Bedienungsanleitung

Konica Minolta

Konica Minolta MYIRO-1 Bedienungsanleitung

Konica Minolta

Konica Minolta CM-26dG Technische Daten

Konica Minolta

Konica Minolta RANGE7 Bedienungsanleitung

Konica Minolta

Konica Minolta CM-600d Bedienungsanleitung

Konica Minolta

Konica Minolta CR-14 Bedienungsanleitung

Konica Minolta

Konica Minolta CS-2000A - AUTRE Bedienungsanleitung

Konica Minolta

Konica Minolta CM-3700D Bedienungsanleitung

Konica Minolta

Konica Minolta CS-2000 Bedienungsanleitung

Konica Minolta

Konica Minolta MULTI GLOSS 268Plus Bedienungsanleitung

Konica Minolta

Konica Minolta CL-70F Bedienungsanleitung

Konica Minolta

Konica Minolta REGIUS 110 HQ Bedienungsanleitung

Konica Minolta

Konica Minolta SPAD-502 PLUS Bedienungsanleitung

Konica Minolta

Konica Minolta CM-M6 Bedienungsanleitung

Konica Minolta

Konica Minolta JM-103 Bedienungsanleitung

Konica Minolta

Konica Minolta CS-3000HDR Bedienungsanleitung

Konica Minolta

Konica Minolta CA-310 Bedienungsanleitung

Konica Minolta

Konica Minolta CM-3600D Bedienungsanleitung

Konica Minolta

Konica Minolta CS-2000 Bedienungsanleitung

Konica Minolta

Konica Minolta AeroDR SKR 4000 Bedienungsanleitung

Konica Minolta

Konica Minolta CM-600d Bedienungsanleitung

Konica Minolta

Konica Minolta CM-512M3 Bedienungsanleitung

Konica Minolta

Konica Minolta CL-70F Bedienungsanleitung

Konica Minolta

Konica Minolta CA-410 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung