Korenix JetCon 2301 V2 Series Bedienungsanleitung

JetCon 2301 V2 Series

Industrial Fast Ethernet to Fiber Media Converter

Quick Installation Guide

www.korenix.com

V1.0

Introduction

JetCon 2301 V2 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of

forwarding modes – Store and Forward, Modied Cut-through, Pure Converter and Converter

with auto-change modes. The JetCon 2301 V2 adopts rugged aluminum case with IP31

grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh environments with

severe electromagnetic interference and -25~70°C (JetCon 2301 V2) or -40~75°C (JetCon

2301 V2-w). It features Link Loss Forwarding to forward link status changes for alerting

remote or central management systems when a remote fault occurs. It also adopts one relay

output to alarm users if a port link fails or if the power fails. Alarms can be enabled/ disabled

by dip switch.

JetCon 2301 V2 has redundant power inputs with wide range DC10~60V through the 6-pin

removable terminal block. The ber port supports Single-mode or Multi-mode for providing

up to 30KM extended distance transmission.

Package Checklist

Unpack the box and you will nd

4JetCon 2301 V2 Industrial Media Converter

4Quick Installation Guide

Mounting the Unit

Din-Rail mount: Mount the din-rail clip on the rear of

JetCon 2301 V2 on the DIN rail.

For information about the DIN Rail installation, please refer to

user’s manual.The user manual can be downloaded from the

Korenix Web site as below: http://www.korenix.com/downloads.htm

Grounding JetCon 2301 V2

There is one grounding screw on the bottom side of

JetCon 2301 V2 . Connect the frame grounding of JetCon

2301 V2 to the grounding surface to ensure safety and

prevent noise for communication interference.

Chassis connects

to the Earth Ground

JetNet 2301 V2 Series

IndustrialFast Ethernet to Fiber Rail Media Converter

Quick Installation Guide

www.korenix.com

V1.0

Wiring the Power Inputs

Wiring the Relay Output

1. Insert the positive and negative wires into the V+ and V- contact on the terminal block

connector.

The relay output contacts are in the middle of the terminal block connector as shown in

gure-3. By inserting the wires and by setting the DIP switch of the respective alarm function

to “ON”, relay output alarm will detect port or power fault, and form a short circuit. The alarm

relay output is “Normal Open”. See, Figure-3. For detailed information, please refer to

chapter 2-5 of the User’s Manual.

2. Tighten the wire-clamp screws to prevent the power wires from being loosened.

Note: The recommended working voltage is DC 24V (Input range: DC10~ 60 V)

Accept 24AWG wire. JetCon 2301

V2 provides auto-polarity reverse

Note: The relay contact supports only 1A current,

DC 24V. It is not recommended to apply higher

voltage and current higher than this specication.

Maximum 1A Current / DC 24V

Alarm System

Extra Power

System

Connecting to Network

1. Connecting the Ethernet Port: Connect one end of an Ethernet cable into the UTP port of

JetCon 2301 V2, while the other end is connected to the attached networking device. UTP

port supports auto MDI/MDIX function. The LNK / ACT LED will turn on and start ashing to

indicate RJ-45 port links and the packets received and transmitted from RJ-45.

2. Connecting the Fiber Port: Connect the ber port of your JetCon 2301 V2 to another Fiber

Ethernet device, by following the gure below. Wrong connection or wrong ber cable type

will cause the ber port not working properly.

3. For different link distances, the JetCon 2301 V2 provides JetCon 2301 V2-m” for multi-

mode ber and “JetCon 2301 V2-s” for single-mode ber.

4. The table below illustrates ber transceiver specication.

xPwr(Min):Minimum Launch Power TxPwr(Max):Maximum Launch Power

RxPwr(Min):Maximum Receive Sensitivity RxPwr(Max):Minimum Receive Sensitivity

Link Budget=Minimum Launch Power –Maximum Receive Sensitivity

Note: To ensure your ber converter can transmit/receive data between the 2 nodes, the

attenuation of the optical ber cable should be smaller than the ber converter’s Link Budget.

This is a Class 1 Laser/LED product.

Don't stare into the Laser/LED Beam.

ATTENTION

！

RX A TX B

TX A RX B

Cable Wiring(SC to SC)

JetCon

2301 V2-m

JetCon

2301 V2-s 30km

2KM

Modul Fiber (um) ConnecterWavelength(um) TXPwr

(Min)

TxPwr

(Max)

RxPwr

(Min)

RxPwr

(Max) LinkBudg(dBm) Distance(km)

Single-Mode

8-10/125 SC 1310nm -15dBm-8dBm-34dBm 8dBm 19dBm

Multi-Mode

50~62.5/125 SC 1310nm -20dBm-14dBm-31dBm 0dBm11dBm

JetCon 2301 V2 DIP Switch Setting

Korenix Customer Service

Description

Enable Link Loss Forwarding function.

Disable Link Loss Forwarding function (Default)

Set TX port in 10 Mbps Half Duplex mode

Set TX port in Auto-Negotiation mode.(Default)

Enable power alarm

Disable power alarm (default)

Enable port alarm

Disable port alarm (default)

Disable Flow control

Enable Flow control (default)

Store and Forward forwarding mode (default mode)

Pure Converter forwarding mode

Modify Cut-Through forwarding mode

Converter mode with Auto-Change forwarding mode

Status

Off

DIP 3

Off

DIP 4

Off

Pin No. #

DIP 1

DIP 2

DIP 5

DIP 6

DIP 7

1235674

123567

Note: After adjusting the DIP-switch, please reboot the unit to activate the new settings.

KoreCARE is Korenix Technology’s global service center, where our professional staffs are

ready to answer your questions at any time.

Korenix global service center’s e-mail is [email protected]

概述

JetCon 2301 V2是一款单口快速光电信号转换器，支持4种转发模式：存储转发，修改直通,

纯转换和转换模式。JetCon 2301 V2配备铝合金外壳，可适应-25~70°C恶劣工作环境，并提

供-40~75°C宽温版本可选，而且可以抵御严重的电磁干扰影响。它满足IP-31工业防护等级，

支持1.5KV Hi-Pot高压隔离保护。JetCon 2301 V2支持LLF(Link Loss Forwarding)远程故障检

测技术，一旦远程发生断线就会触发报警，此外，它还装备有一路继电器报警输出，可针对断

线断电事件进行报警。继电器报警可以通过DIP拨码开关启动或关闭。

JetCon 2301 V2支持DC10~60V宽范围冗余电源输入，配备6-pin可拆卸接线槽。光口支持单

模或多模两种机型满足不同传输距离的要求，最大传输距离可达30KM。

设备安装

JetCon 2301 V2设备接地

导轨安装：将导轨夹固定在JetCon 2301 V2的背

面，然后卡上导轨。更多导轨安装信息，请参考用

户操作手册。

您可以登录Korenix网站到如下地址下载用户手册:

http://www.korenix.com/downloads.htm

在JetCon 2301 V2的底部有一个接地螺母。

将JetCon 2301 V2的接地螺母接地，

确保设备安全，防止电气干扰。 Chassis connects

to the Earth Ground

包装清单

打开包装，核对产品清单

4JetCon 2301 V2工业信号转换器

4快速安装向导

JetNet 2301 V2 Series

IndustrialFast Ethernet to Fiber Rail Media Converter

Quick Installation Guide

www.korenix.com

V1.0

电源连接

继电器报警连线

1. 将电源的正负极分别接入设备底部接线槽的V+ 和V-接口。

如图3所示，继电器报警触点位于电源接线槽的中间位置。将报警线路接入固定，并将DIP拨

码开关置“ON”启动报警功能，继电器报警系统会自动检测端口及电源断连情况并组成一个

闭合回路。继电器报警线路默认是开路。欲了解更多信息，请参看用户手册chapter 2-5。

2. 拧紧电源接线螺丝，防止电源线脱落。

备注:建议工作电压为DC 24V (供电范围:DC10~60 V)

接线槽支持12~24AWG 电源线。

JetCon 2301 V2支持电源正负

极性反接保护

备注:继电器报警触点仅支持1A 电流，DC 24V电

压。不建议在此线路中使用更高电压和电流。

Maximum 1A Current / DC 24V

Alarm System

Extra Power

System

网络连接

1. 网口连线:将UTP双绞线的一端连接到JetCon 2301 V2的电口，另一端连接到相关网络设

备。UTP端口自适应MDI/MDIX。LNK / ACTLED指示灯会亮起并闪烁，表示RJ-45端口已连

接并正在收发数据。

2. 光口连线:如图所示，将光纤的一端连接到JetCon 2301 V2，另一端连接到相关设备，进行

交叉互连。错误的连线会导致光口无法工作。

3. 针对不同传输距离，JetCon 2301 V2提供“JetCon 2301 V2-m”多模光口机型和

“JetCon 2301 V2-s”单模光口机型。

4. 以下图表为光收发器规格

TxPwr(Min):最小发射功率 TxPwr(Max):最大发射功率

RxPwr(Min):最小接收灵敏度 RxPwr(Max):最大接收灵敏度

Link Budget=最小发射功率 –最大接收灵敏度

备注:为了确保光电转换器在2节点间能够正常收发数据，光纤线材的衰减值一定要低于转换

器的Link Budget值。

此为Class 1 Laser/LED光口产品，

切勿直视激光束

传输距离(km)

波长(um)接头机型

！

RX A TX B

TX A RX B

Cable Wiring(SC to SC)

JetCon

2301 V2-m

JetCon

2301 V2-s 30km

2KM

Fiber (um) TXPwr

(Min)

TxPwr

(Max)

RxPwr

(Min)

RxPwr

(Max) LinkBudg(dBm)

Single-Mode

8-10/125 SC -15dBm-8dBm-34dBm 8dBm 19dBm

Multi-Mode

50~62.5/125 SC

1310nm

1310nm -20dBm-14dBm-31dBm 0dBm11dBm

备注

JetCon 2301 V2 DIP拨码开关设定

科洛理思售后服务

描述

启动LLF(Link Loss Forwarding)功能.

关闭LLF(Link Loss Forwarding)功能 (默认)

将TX端口设置为10 Mbps半双工模式

将TX端口设置为自动协商模式(默认)

启动电源报警

关闭电源报警 (默认)

启动端口报警

关闭端口报警 (默认)

关闭流控制

启动流控制(默认)

存储转发模式(默认模式)

纯转换模式

Modify Cut-Through转发模式

转换Auto-Change模式

状态

Off

DIP 3

Off

DIP 4

Off

Pin No. #

DIP 1

DIP 2

DIP 5

DIP 6

DIP 7

1235674

123567

备注:更改DIP拨码开关设置以后，请重启设备让新设置生效。

KoreCARE 是科洛理思网络科技全球服务中心，我们专业的技术人员随时准备解答您的疑问。

Inhaltsverzeichnis

Andere Korenix Medienkonverter Handbücher

Korenix

Korenix JetCon 2302 Bedienungsanleitung

Korenix

Korenix JetCon 3401G Bedienungsanleitung

Korenix

Korenix JetCon 1701GP-U Bedienungsanleitung

Korenix

Korenix JetCon 2301S Bedienungsanleitung

Korenix

Korenix JetCon 3401G V2 Bedienungsanleitung

Korenix

Korenix JetCon 1100 Series Bedienungsanleitung

Korenix

Korenix JetCon 3701GP-U Bedienungsanleitung

Korenix

Korenix JetCon 3401G Bedienungsanleitung

Korenix

Korenix JetCon 1302 Series Bedienungsanleitung

Korenix

Korenix JetCon 3301 Series Bedienungsanleitung

Korenix

Korenix JetCon 3701G Bedienungsanleitung

Korenix

Korenix JetCon 2201-w Bedienungsanleitung

Korenix

Korenix JetWave 2212X/S Bedienungsanleitung

Korenix

Korenix JetCon 2302 Bedienungsanleitung

Korenix

Korenix JetCon 2301S Bedienungsanleitung

Korenix

Korenix JetCon 2401-S Bedienungsanleitung

Korenix

Korenix JetCon 2301 Bedienungsanleitung

Korenix

Korenix JetCon 3401G Bedienungsanleitung

Korenix

Korenix JetCon 1301 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung