Korenix JetCon 3401G Bedienungsanleitung

JetCon 3401G

Industrial Gigabit Ethernet Media Converter

Quick Installation Guide

V1.0 2-Oct-2008

www.korenix.com

Korenix Technology Co., Ltd.

Introduction

The JetCon 3401G Industrial Gigabit Ethernet Converter, conforming IEEE 802.3 10Base-T, 802.3u

100Base-TX and 1000Base-T/SX/LX standard, supports RJ-45 copper to Gigabit fiber conversion

using store and forward technology. The JetCon 3401G adopts rugged metal case design to operate in

harsh environments (-25℃~70℃); It also provides IP-31 standard protection. It features Link Loss

Forwarding to raise an alarm when a remote fault occurs and also adopts one relay output to alarm

users if a port link fails or if the power fails. Alarms can be enabled/ disabled by dip switch. The fiber

port supports SFP socket for several of SFP transceiver to achieve different link distance.

JetCon 3401G is recommended to be powered by DC 24V with 12~48V range from the 6-pin

removable terminal block.

Package contents Check List

Box contents:

¾JetCon 3401G

¾Quick Installation Guide

¾CD User Manual CD User manual

JetCon 3401G QIG

Mounting the Unit

¾Din-Rail mount: Mount the din-rail clip screwed on the

rear of JetCon 3401G on the DIN rail.

For information about the DIN Rail installation, please refer user’s

manual.

Wiring the Power Inputs

1. Insert the positive and negative wires into the

V+ and V- contact on the terminal block

connector.

2. Tighten the wire-clamp screws to prevent the

DC wires from being loosened. See Figure-1

Notes: The recommended working voltage is

DC24V (DC12~ 48V).

Figure-1

Korenix Technology Co., Ltd.

Wiring the Relay Output

The relay output alarm contacts are in the

middle of the terminal block connector as

shown in figure-3.

By inserting the wires and settings the DIP

switch of the respective alarm function to

“ON”, relay output alarm will detect port or

power fault, and form a short circuit. The alarm relay

output is “Normal Open”. See, Figure -2. For more

information, please refer chapter 2-4, 2-5 for more

detail information.

Figure-2

Wiring the Earth Ground

In an industrial environment, there might be devices

that generate electromagnetic noise, such as AC

motors, electric welding machine, or a power generator.

These devices will generate electric noise or surges

that might disturb communications. To prevent those

noises, the device should be well earthed. In the

Figure- 3 shows how to make connection. Figure-3

Connecting to Network

1. Connecting the Ethernet Ports: Connect one end of an Ethernet cable into the UTP port of

JetCon 3401G, while the other end is connected to the attached networking device. The UTP

ports support auto MDI/MDIX function. The Speed LED will turn on for 1000M link and blinking

for 100Mbps link; the LNK/ACT LED will turn on for link up and blinking for packet transmits

and receives.

2. Install Gigabit SFP transceiver and make the connection:

Connect the fiber port on your JetCon 3401G to another Gigabit

Fiber Ethernet device, by following the figure below. Wrong

connection will cause the fiber port not working properly.

The SFP Fiber port supports 2 LEDs for link/activity and full

duplex/collision; once the gigabit fiber port is link up, the link LED

will be trigger to “ON” ATTENTION

This is a Class 1 Laser/LED product.

Don’t stare into the Laser/LED Beam.

Korenix Technology Co., Ltd.

DIP Switch Settings for Alarm Relay Output and Link Loss Forwarding

Pin No. # Status Description

ON To enable port link down alarm at this port.

# 1

Port Event Alarm Off To disable port link down alarm at this port.

ON To enable power failure alarm.

Power Event Alarm Off To disable power failure alarm.

To enable Link Loss Forwarding function at both of fiber and copper

port.

Once either one of copper or fiber port is disconnected, the JetCon

3401G will forced to turn-off the other port to alert the end of

attached device.

Note: Once the LLF is active and the cable event is recovered,

the LLF DIP-switch must be re-triggered to arouse this function.

LLF

(Link Loss Forwarding)

Off To disable Link Loss Forwarding function.

Korenix Customer Service

KoreCARE is Korenix Technology’s global service center, where our professional staffs are ready

to solve your problems at any time.

Korenix global service center’s e-mail is [email protected]

Andere Handbücher für JetCon 3401G

Inhaltsverzeichnis

Andere Korenix Medienkonverter Handbücher

Korenix

Korenix JetCon 1301 Series Bedienungsanleitung

Korenix

Korenix JetCon 2301S Bedienungsanleitung

Korenix

Korenix JetCon 3701GP-U Bedienungsanleitung

Korenix

Korenix JetCon 1100 Series Bedienungsanleitung

Korenix

Korenix JetCon 3301 Series Bedienungsanleitung

Korenix

Korenix JetCon 2301S Bedienungsanleitung

Korenix

Korenix JetCon 2301 Bedienungsanleitung

Korenix

Korenix JetCon 2302 Bedienungsanleitung

Korenix

Korenix JetCon 2201-w Bedienungsanleitung

Korenix

Korenix JetWave 2212X/S Bedienungsanleitung

Korenix

Korenix JetCon 2301 V2 Series Bedienungsanleitung

Korenix

Korenix JetCon 3401G Bedienungsanleitung

Korenix

Korenix JetCon 3401G Bedienungsanleitung

Korenix

Korenix JetCon 1701GP-U Bedienungsanleitung

Korenix

Korenix JetCon 3701G Bedienungsanleitung

Korenix

Korenix JetCon 2302 Bedienungsanleitung

Korenix

Korenix JetCon 1302 Series Bedienungsanleitung

Korenix

Korenix JetCon 2401-S Bedienungsanleitung

Korenix

Korenix JetCon 3401G V2 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung