Kramer VS-1616DN-MD Bedienungsanleitung

VS-1616DN-MD Quick Start (P/N: 2900-300662QS REV 1)

P/N:

2900- 300662QS

Rev:

Scan for full manual

VS-1616DN-MD Quick Start Guide

This guide helps you install and use your VS-1616DN-MD for the first time.

Go to www.kramerav.com/downloads/VS-1616DN-MD to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VS-1616DN-MD 2x2 to 16x16 Modular Multi-

Format Digital Matrix Switcher

1 Set of rack ears (attached)

1 Quick start guide

Kramer RC-IR3infrared remote control transmitter

with batteries

2 Power cords

Step 2: Get to know your VS-1616DN-MD

Feature

Function

Double-

function

Selector

Buttons

Area

Button

Functions

ESC

Press to exit the current operation.

EDID

Press to assign EDID channels.

STO

Press to store the current setup in a preset. After pressing the MENU button, this button lights

and is enabled.

ALL

Press to connect an input to all outputs. After pressing the MENU button, this button lights and

is enabled.

OFF

Press to turn off an output. After pressing the MENU button, this button lights and is enabled.

RCL

Press to recall a preset. After pressing the MENU button, this button lights and is enabled.

DELAY

Press to set the delaybetween confirming an action and the execution of the action.

ENTER

Press to complete the input-output setup when using a one-digit number instead of two digits.

For example, to enter input 5, you can press either 05 or 5, ENTER.

Press to enter the options in a setup menu.

BREAKAWAY Button

Press to exit a menu.

DEFAULT SETUP Button

Press to recall the default setup.

IR Receiver

Infrared remote control sensor.

IR LED

Lights yellow when receiving commands from the IR remote control transmitter.

PS-1/PS-2 POWER LED

Lights green when power supply is active. Briefly remains lit after powering off the device.

Feature

Function

PS-1/PS-2 ERROR LED

Lights red when an error is detected. Briefly lights red immediately following a power disruption

(e.g., cable disconnection, power off, and so on).

TAKE Button

Press to confirm actions.

MENU Button

Press once to enable the ALL, OFF, STO and RCL buttons.

Press again to enter the configuration menu.

When in a Menu, press to cycle through the menu items.

LOCK Button

Press and hold for approximately 2 sec to lock/unlock the front panel buttons.

OUTPUTS/INPUTS

LCD Display

Displays the outputs (upper row) switched to the selected inputs (lower row).

Displays user interface messages and menus.

Front Panel Locking Screws

Release the 14 front panel locking screws to open the front panel and access the fan arrays.

Power Supply Thumbscrews

Release the 4 power supply thumbscrews to install / remove either of the VS-1616DN-MD

power supplies. The VS-1616DN-MD can function normally with a single power supply.

◄ (Backward)

Press to shift the sliding window to the right (the LCD display onlyshows 13 cross-points out of

a total of 16).

1, 2, 3, 4, 5, 6, 7, 8, 9, 0

Numeric keypad, 1 to 0.

► (Forward)

Press to shift the sliding window to the left (the LCD display only shows 13 cross-points out of

a total of 16).

Feature

Function

PS-1 AC Mains Power Module

Power supply 1: Fuse holder and power cord socket. Connect to the AC mains supply.

RS-232 9-pin D-sub Port

Connects to the remote operation PC or remote controller. If the unit is not the first unit in

the line, connects to the RS-232 OUT 9-pin DB port of the previous unit in the line.

IN 1~8 Connectors

INPUTS

Connect to the relevant video sources, depending on the cards installed

(1 to 8).

IN 9~16 Connectors

Connect to the relevant video sources, depending on the cards installed

(9 to 16).

TEST Module

Signal generator module for testing video and audio outputs.

RESOLUTION DIP-switches

Set the resolution for video generated by the Test module.

PATTERN Button

Press the button repeatedly to change the video pattern generated by the Test module.

PS-2 AC Mains Power Module

Power supply 2: Fuse holder and power cord socket. Connect to the ACmains supply.

NET Ethernet RJ-45 Connector

Connect to a PC orcontroller via the Ethernet LAN.

LINK LED flashes when communication is active. POWER LED lights when the

interface receives power.

OUT 1~8 Connectors

OUTPUTS

Connect to the relevant video acceptors, depending on the cards installed (1 to 8).

OUT 9~16 Connectors

Connect to the relevant video acceptors, depending on the cards installed (9 to 16).

Test Module DVI Molex 24-pin Video

Connector

Connect to one of the relevant video inputs/outputs to aid in troubleshooting.

Test Module 3.5mm Mini Jack

Unbalanced Analog Audio Connector

Connect to one of the relevant audio inputs/outputs to aid in troubleshooting.

Step 3: Install the VS-1616DN-MD

To rack mount the machine, the VS-1616DN-MD is pre-assembled with ear brackets attached to the

machine.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-1616DN-MD. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the VS-1616DN-MD.

Note: the maximum number of ports may vary.

Port Numbering:

On all cards apart from the DVI dual link cards, there are two physical ports on each card and numbering of ports is sequential from top to

bottom and left to right. Each DVI dual link card provides one physical port which causes the loss of one number in the numbering

sequence of that card only:

Diagram #

Actual Port #

IN 1

IN 2

IN 3

IN 5

IN 6

OUT 2

OUT 1

OUT 3

OUT 5

OUT 6

Step 5: Connect the power

Connect the two AC power cables to the rear of the VS-1616DN-MD, turn on both power switches and then switch on the power of

connected devices.

Step 6: Set operation parameters

The VS-1616DN-MD does not have separate output and input

buttons. Instead, the front panel includes a numeric keypad.

When the unit is powered-on, the last matrix setup that was

used is loaded. Use either the setup recall (records a stored

configuration from a preset) or default setup recall (for quick

retrieval of a commonly used programmable default setup)

functions to retrieve other setups.

The LCD display can showonly 13 out of the 16 available matrix

combinations at once. To view any of the matrix combinations

use the ◄ or the ► buttons on the front panel to shift the sliding

windowto the right or left.

After switching on the power, the LCD displayshows the following

screens in sequence:

Step 7: Operate via the front panel buttons and via the:

IR remote controller:

RS-232 and Ethernet:

See the RC-IR3 user manual for

information on using the remote

controller.

RS-232

Protocol 2000/3000

Baud Rate:

9600

Data Bits:

Stop Bits:

Parity:

None

Command Format:

HEX

P2000, to switch Input 4 to Output 2:

0x01, 0x84, 0x82, 0x81

P3000, to switch Input 4 to Output 2:

#AV 4>2

Ethernet

IP Address:

192.168.1.39

TCP Port #:

5000

UDP Port #:

50000

Full Factory Reset

Front Panel

Press MENU twice. Select Total Matrix Reset >

Factory Reset. Press TAKE twice.

EDID

EDIDdata is passed between Output 1 and Input 1

Step 8: Set the number of input or output ports

After installing or removing a module you need to set the number of input and output ports so that the VS-1616DN-MD recognizes the

new configuration.

To set the number of input or output ports:

1. Press ESC, ENTER and LOCK together. The following is displayed:

Configuration Device

2. Press ENTER. The following is displayed:

Test Board: 1 MaxInput:17 MaxOutput:17

Note: The number of input and output ports can only be set in units of two, for example, 4 x 4, 16 x 4 or 12 x 16.

3. Using the numeric keys, enter the number of input and output ports installed. The TAKE button flashes.

4. Press TAKE. The number of installed ports is saved and the displayreverts to the output/input display.

5. Reboot the device by turning the power off and then on again.

Andere Kramer Matrix-Umschalter Handbücher

Kramer

Kramer VP-32x1 Bedienungsanleitung

Kramer

Kramer VS-44HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Kramer

Kramer VS-88HD Bedienungsanleitung

Kramer

Kramer VS-626 Bedienungsanleitung

Kramer

Kramer Sierra Viddeo 84V3S Bedienungsanleitung

Kramer

Kramer VP-26 Bedienungsanleitung

Kramer

Kramer Sierra Video 1608V3 Bedienungsanleitung

Kramer

Kramer 1608HD Bedienungsanleitung

Kramer

Kramer XL 1616VS Bedienungsanleitung

Kramer

Kramer XL 1208V4 Bedienungsanleitung

Kramer

Kramer VS-44H2A Bedienungsanleitung

Kramer

Kramer VP-729 Bedienungsanleitung

Kramer

Kramer VS-42HDCP Bedienungsanleitung

Kramer

Kramer Sierra Video 3248V5xl Bedienungsanleitung

Kramer

Kramer VP-1608 Bedienungsanleitung

Kramer

Kramer Sierra Video 4832V5xl Bedienungsanleitung

Kramer

Kramer VS-48HDxl Bedienungsanleitung

Kramer

Kramer VP-778 Bedienungsanleitung

Kramer

Kramer VP-720DS Bedienungsanleitung

Kramer

Kramer VS-88HDCPxl Bedienungsanleitung

Kramer

Kramer VS-48HDCPxl Bedienungsanleitung

Kramer

Kramer Sierra Video 4864V5Sxl Bedienungsanleitung

Kramer

Kramer 3232S Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Shinybow USA

Shinybow USA SB-8811 Bedienungsanleitung

Optimus

Optimus Compact Bedienungsanleitung