Kramer VS-3232DVI Bedienungsanleitung

Kramer Electronics, Ltd.

USER MANUAL

Model:

VS-3232DVI

32x32 DVI Matrix Switcher

Contents

1Introduction 1

2Getting Started 1

2.1 Quick Start 1

3Overview 3

3.1 Defining EDID 4

3.2 Recommendations for Best Performance 4

4Defining the VS-3232DVI 32x32 DVI Matrix Switcher 4

4.1 Using the IR Transmitter 8

5Installing the VS-3232DVI in a Rack 9

6Connecting the VS-3232DVI 32x32 DVI Matrix Switcher 10

6.1 Connecting to the VS-3232DVI via RS-232 11

6.1.1 Connecting to a Male 9-pin D-sub Connector 11

6.1.2 Connecting to a Female 9-pin D-Sub Connector 12

6.2 Connecting to the VS-3232DVI via Ethernet 12

6.2.1 Connecting the Ethernet Port directly to a PC 12

6.2.2 Connecting to the Ethernet Port via a Network Switch/Hub 14

7Operating Your Video Matrix Switcher 14

7.1 Startup Display 14

7.1.1 Viewing the Display 15

7.2 Using the Selector Buttons 15

7.3 Confirming Actions 15

7.3.1 Toggling between the At Once and Confirm Modes 16

7.3.2 Confirming a Switching Action 16

7.4 Switching Actions 16

7.4.1 Switching one Input to one Output 16

7.4.2 Switching Several Inputs to Several Outputs 17

7.4.3 Turning an Output Off 17

7.4.4 Turning Off Several Outputs 18

7.4.5 Recalling the Default Setup 18

7.5 Locking the Front Panel Buttons 18

8Using the Configuration Menus 19

8.1 Using the Setup Menu 19

8.1.1 Setup Menu—1: inXX=>ALL, Switching one Input to all Outputs 19

8.1.2 Setup Menu—3: outXX=>OFF, Turning an Output Off 20

8.1.3 Setup Menu—7: EDID, Assignment to an Input 20

8.1.4 Setup Menu—9: Delay, Setting for an Output 21

8.1.5 Setup Menu—4: store setup XX, Storing the Setup in a Preset 21

8.1.6 Setup Menu—6: recall setup XX, Recalling a Preset 22

8.2 Using the Config Menu 23

8.2.1 Config Menu—Input Signal Detection Display 23

8.2.2 Config Menu—Output Load Detection Display 24

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Contents

8.2.3 Config Menu—Interface Configuration 24

8.2.4 Config Menu—Interface Reply Configuration 25

8.2.5 Config Menu—Protocol Configuration 25

8.2.6 Config Menu—Store Default Setup 25

8.2.7 Config Menu—Total Matrix Reset 26

8.2.8 Config Menu—Display Firmware Versions 27

9Configuring the Number of Installed Input and Output Ports 27

10 Installing and Using the Test Module to Troubleshoot Video Problems 28

10.1 Installing the Test Module 28

10.2 Setting the Resolution of the Generated Video 28

10.3 Setting the Pattern of the Generated Video 29

10.4 Using the Test Module to Troubleshoot Video Problems 29

10.4.1 Testing the Projector Output 30

10.4.2 Testing the Output Signal Path to the Projector 30

10.4.3 Testing the Input and Output Signal Path to the Projector 30

11 Upgrading the VS-3232DVI Firmware 30

12 Technical Specifications 31

13 Factory Default EDID 31

14 Communication Protocols 33

Figures

Figure 1: VS-3232DVI 32x32 DVI Matrix Switcher Front Panel 5

Figure 2: VS-3232DVI Numeric Keypad 6

Figure 3: VS-3232DVI 32x32 DVI Matrix Switcher Rear Panel 7

Figure 4: Connecting the VS-3232DVI 10

Figure 5: Crossed Cable RS-232 Connection 11

Figure 6: Local Area Connection Properties Window 13

Figure 7: Internet Protocol (TCP/IP) Properties Window 13

Figure 8: Default Startup Status Display Sequence 14

Figure 9: Resolution DIP-switch 29

Figure 10: Signal Paths for Isolating problems 29

Tables

Table 1: Front Panel VS-3232DVI 32x32 DVI Matrix Switcher Front Panel Features 6

Table 2: Front Panel VS-3232DVI Numeric Keypad Labels 6

Table 3: VS-3232DVI 32x32 DVI Matrix Switcher Rear Panel Features 8

Table 4: Available Resolutions of Generated Video 28

Table 5: Technical Specifications of the 32x32 DVI Matrix Switcher 31

Table 6: Hex Table (IN 1-32 to OUT 1-16) 33

Table 7: Hex Table (IN 1-32 to OUT 17-32) 35

Introduction

1 Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been

providing a world of unique, creative, and affordable solutions to the vast range of

problems that confront the video, audio, presentation, and broadcasting

professional on a daily basis. In recent years, we have redesigned and upgraded

most of our line, making the best even better! Our 1,000-plus different models now

appear in 11 groups1

Congratulations on purchasing your Kramer VS-3232DVI 32x32 DVI Matrix

Switcher. This product is ideal for the following typical applications:

that are clearly defined by function.

•Professional display systems requiring video signal routing

•Broadcast, presentation and production facilities, as well as monitoring in

large duplication systems

•Rental/staging applications

The package includes the following items:

•VS-3232DVI 32x32 DVI Matrix Switcher

•Power cord

•Kramer RC-IR3infrared remote control transmitter (including the required

batteries and a separate user manual2) and this user manual2

2 Getting Started

We recommend that you:

•Unpack the equipment carefully and save the original box and packaging

materials for possible future shipment

•Review the contents of this user manual

•Use Kramer high performance, high resolution cables3

2.1 Quick Start

This quick start chart summarizes the basic setup and operation steps.

1 GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Matrix Switchers; GROUP 3: Control Systems; GROUP 4:

Format/Standards Converters; GROUP 5: Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7: Scan

Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9: Room Connectivity; GROUP 10: Accessories and Rack

Adapters; GROUP 11: Sierra Products

2 Download up-to-date Kramer user manuals from http://www.kramerelectronics.com

3 The complete list of Kramer cables is available from http://www.kramerelectronics.com

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Getting Started

Overview

3 Overview

The Kramer VS-3232DVI is a high performance 32x32 matrix switcher3F

1for DVI

signals. It features a video bandwidth of over 1.65GHz that ensures transparent

performance even in the most critical applications. The unit reclocks and equalizes

the signal and can route any or all inputs to any or all outputs simultaneously.

The VS-3232DVI is highly configurable–you can add or remove both inputs and

outputs independently in groups of four. For example, you can configure a device

as a 4x24 or 32x12 matix switcher to perfectly suit your needs.

The VS-3232DVI features:

•Full 32x32 non-blocking matrix array to switch any of the 32 input DVI video

signals to any or all outputs

•59 preset memory locations for quick access to user-defined setups

•Fast access to a preprogrammed default preset configuration

•A default EDID (Extended Display Identification Data) assigned to each input

•The Kramer 2000 Protocol

•A 40 character by 2 line LCD showing operational status and configuration menu

•A LOCK function to prevent tampering with the front panel

•I-EDIDPro™ Kramer Intelligent EDID Processing™ – Intelligent EDID

handling and processing algorithm ensures plug and play operation for DVI

systems

You can operate the VS-3232DVI via the front panel buttons4F

2or remotely via:

•RS-232 serial commands transmitted by a touch screen system, PC or other

serial controller

•Ethernet

•The infrared remote control transmitter

The VS-3232DVI is housed in a 19" 5U rack mountable enclosure.

To achieve the best performance:

•Connect only good quality connection cables, thus avoiding interference,

deterioration in signal quality due to poor matching, and elevated noise levels

(often associated with low quality cables)

•Avoid interference from neighboring electrical appliances that may adversely

influence signal quality and position your Kramer VS-3232DVI in a location

free from moisture and away from excessive sunlight and dust

1 Can also be configured for other sizes up to a maximum of 32 x 32

2 The VS-3232DVI is a sophisticated device but has been designed to be as simple as possible to operate. Due to space limitations on the

front panel, 64 input/output selector buttons are instead substituted by a keypad. For details of how to route inputs to outputs, see

Section 7.2

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Defining the VS-3232DVI 32x32 DVI Matrix Switcher

3.1 Defining EDID

The Extended Display Identification Data (EDID1

3.2 Recommendations for Best Performance

) is a data-structure provided by

a display, to describe its capabilities to a graphics card (that is connected to the

display’s source). The EDID enables the video source to “know” what kind of

monitor is connected to the output. The EDID includes the manufacturer’s name,

the product type, the timing data supported by the display, the display size,

luminance data and (for digital displays only) the pixel mapping data.

To achieve the best performance:

•Connect only good quality connection cables, thus avoiding interference,

deterioration in signal quality due to poor matching, and elevated noise levels

(often associated with low quality cables)

•Avoid interference from neighboring electrical appliances and position your

VS-3232DVI away from moisture, excessive sunlight and dust

4 Defining the VS-3232DVI 32x32 DVI Matrix Switcher

Figure 1, Table 1, Figure 2 and Table 2 define the front panel, and Figure 3 and

Table 3 define the rear panel of the VS-3232DVI.

1 Defined by a standard published by the Video Electronics Standards Association (VESA)

Defining the VS-3232DVI 32x32 DVI Matrix Switcher

Figure 1: VS-3232DVI 32x32 DVI Matrix Switcher Front Panel

Note: Buttons 12, 13 and 14 function as the TAKE, MENU and LOCK buttons respectively

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Defining the VS-3232DVI 32x32 DVI Matrix Switcher

Table 1: Front Panel VS-3232DVI 32x32 DVI Matrix Switcher Front Panel Features

Feature

Function

Double-

function

Selector

Buttons

Area

Buttons

ESC Press to exit the current operation

2 EDID Press to assign EDID channels

3 STO

Press to store the current setup in the a preset

4 ALL

Press to connect an input to all outputs

5 OFF

Press to turn off an output

6 RCL1Press to recall a preset

7 DELAY Press to set the delay between confirming an action and the execution of the action

8 ENT Press to complete the input-output setup when using a one-digit number instead of

two digits2

Press to enter the options in a setup menu

9 IR Receiver LED Infrared remote control sensor

10 Power Switch Illuminated switch for turning the unit on or off

11 IR LED Lights yellow when receiving commands from the IR remote control transmitter

12 TAKE Button Press to confirm actions (see Section 7.3.2

)

MENU Button Press once to enable the ALL, OFF STO and RCL buttons (see Section 8).

Press again to enter the configuration menu (see 8.2Section

When in a Menu, press to cycle through the menu items

14 LOCK Button Press and hold for approximately 2 sec to lock/unlock the front panel buttons (see

Section 7.5

)

BREAKAWAY Button Press to exit a Menu (see Section 8

)

DEFAULT SETUP Button Press to recall the default setup (see Section 7.4.5

)

OUTPUTS/INPUTS

LCD Display

Displays the outputs (upper row) switched to the selected inputs (lower row), (see

Section 7.1

Displays user interface messages and menus

Figure 2: VS-3232DVI Numeric Keypad

Table 2: Front Panel VS-3232DVI Numeric Keypad Labels

Feature

Function

18 ◄(Backward) Press to shift the sliding window to the right

19 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 Numeric keypad, 1 to 0

20 ►(Forward) Press to shift the sliding window to the left3

1 This button is enabled and lights after pressing the MENU button

2 For example, to enter input 5, you can either press 05 or 5, ENT

3 Since the LCD display is large enough to show only 13 cross-points out of a total of 32

Defining the VS-3232DVI 32x32 DVI Matrix Switcher

Figure 3: VS-3232DVI 32x32 DVI Matrix Switcher Rear Panel

Inhaltsverzeichnis

Andere Kramer Matrix-Umschalter Handbücher

Kramer

Kramer Sierra Pro XL 1616V5S Bedienungsanleitung

Kramer

Kramer VP-778 Bedienungsanleitung

Kramer

Kramer Sierra Video 6448V5Sxl Bedienungsanleitung

Kramer

Kramer VS-44HDCP Bedienungsanleitung

Kramer

Kramer VS-1616D-MD Bedienungsanleitung

Kramer

Kramer VP-885 Bedienungsanleitung

Kramer

Kramer XL 3216V2 Bedienungsanleitung

Kramer

Kramer VS-84HDCPxl Bedienungsanleitung

Kramer

Kramer VS-62HA Bedienungsanleitung

Kramer

Kramer Sierra Video 3216V3 Bedienungsanleitung

Kramer

Kramer 1616D Bedienungsanleitung

Kramer

Kramer VS-808TP Bedienungsanleitung

Kramer

Kramer VS-5x5 Bedienungsanleitung

Kramer

Kramer VP-4x4xl Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1616V5 Bedienungsanleitung

Kramer

Kramer VS-162V Bedienungsanleitung

Kramer

Kramer VS-6YC Bedienungsanleitung

Kramer

Kramer XL 1208V Bedienungsanleitung

Kramer

Kramer VP-1608 Bedienungsanleitung

Kramer

Kramer XL 1608V4S Bedienungsanleitung

Kramer

Kramer VS-6464DN-EM Bedienungsanleitung

Kramer

Kramer Sierra Video 3216V3S Bedienungsanleitung

Kramer

Kramer VS-88HDCPxl Bedienungsanleitung

Kramer

Kramer Cobra MX-1616 Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Shinybow USA

Shinybow USA SB-8811 Bedienungsanleitung

Optimus

Optimus Compact Bedienungsanleitung