Kramer KDS-EN6 Bedienungsanleitung

P/N: 2900-300655 Rev 7 www.kramerAV.com

USER MANUAL

MODEL:

KDS-EN6 Video Encoder

KDS-DEC6 Video Decoder

WP-EN6 Video Encoder

KDS-EN6 Video Encoder

WP-EN6 Video Encoder

KDS-DEC6 Video Decoder

Kramer Electronics Ltd. 
 
KDS-EN6 / KDS-DEC6 / WP-EN6 –Contents 
i 
 
Contents 
Introduction 1 
Getting Started 1 
Overview 2 
Typical Applications 3 
Defining KDS-EN6 4 
Defining KDS-DEC6 5 
Defining WP-EN6 6 
Initial Setup 7 
Configuring Network Switch 7 
Initial Setup Using Device Buttons 8 
Mounting KDS-EN6 / KDS-DEC6 10 
Installing WP-EN6 10 
Connecting KDS-EN6 / KDS-DEC6 11 
KDS-EN6 / KDS-DEC6 / WP-EN6 Unicast Installation 12 
One-to-Many Configuration 14 
Matrix Configuration 16 
Video Wall Setup 17 
KVM Setup 20 
KVM Roaming Setup 21 
Using Embedded Web Pages 23 
Browsing Web Pages 23 
Modifying and Viewing the System 24 
Setting the Video Wall 31 
Setting Up the Network 35 
Setting Operation Functions 36 
Using the KDS-DEC6 Channel OSD 42 
Operating KDS-EN6 and KDS-DEC6 43 
Setting Up RS-232 over IP 43 
Setting Up USB over IP 47 
Setting Up IR over IP 47 
Fast Video Switching 47 
Resetting the KDS-EN6/ KDS-DEC6 to Factory Default Values 47 
Technical Specifications 48 

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Introduction

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world

of unique, creative, and affordable solutions to the vast range of problems that confront the

video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we

have redesigned and upgraded most of our line, making the best even better!

Unless specified otherwise KDS-EN6 refers to both KDS-EN6 and WP-EN6 in this document.

Getting Started

We recommend that you:

•Unpack the equipment carefully and save the original box and packaging materials for

possible future shipment.

•Review the contents of this user manual.

Go to www.kramerav.com/downloads/KDS-DEC6 to check for up-to-date user manuals,

application programs, and to check if firmware upgrades are available (where appropriate).

Achieving Best Performance

•Use only good quality connection cables (we recommend Kramer high-performance,

high-resolution cables) to avoid interference, deterioration in signal quality due to poor

matching, and elevated noise levels (often associated with low quality cables).

•Do not secure the cables in tight bundles or roll the slack into tight coils.

•Avoid interference from neighboring electrical appliances that may adversely influence

signal quality.

•Position your Kramer KDS-EN6 / KDS-DEC6 / WP-EN6 away from moisture, excessive

sunlight and dust.

Safety Instructions

Caution:

•This equipment is to be used only inside a building. It may only be connected to other

equipment that is installed inside a building.

•For products with relay terminals and GPI\O ports, please refer to the permitted rating

for an external connection, located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•To ensure continuous risk protection, replace fuses only according to the rating

specified on the product label which located on the bottom of the unit.

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Introduction

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce

the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected

and recycled. To comply with the WEEE Directive, Kramer Electronics has made

arrangements with the European Advanced Recycling Network (EARN) and will cover any

costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on

arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular

country go to our recycling pages at www.kramerav.com/support/recycling/.

Overview

Congratulations on purchasing one or more of the of the following Kramer Video

Encoders/Decoders:

•KDS-EN6 Video Encoder

•KDS-DEC6 Video Decoder

•WP-EN6 Video Encoder

Kramer KDS-EN6 / KDS-DEC6 / WP-EN6 Encoder and Decoder units provide AV over IP

network and include 4K video, audio, IR, RS-232 and USB over IP with HDCP 2.2.

KDS-EN6 / KDS-DEC6 / WP-EN6 features:

•Video Support −HDMI™ 4K@60Hz (4:2:0), HDMI 4K@30Hz (4:4:4).

•Audio Support −HDMI/line in, 7.1 PCM, Dolby True-HD, and DTS-HD Master audio.

•Virtualization −IR, USB, RS-232 over IP.

•Network −Managed switch, 1G, multicast, jumbo frames, IGMP snooping layer 2.

•Power −PoE or external power supply.

•Control −Kramer Network, Kramer Control, Web UI, API.

•HDCP −2.2 compliance.

•Flexible video wall setups.

•KDS-EN6 and KDS-DEC6 are MegaTOOLS® size, letting you mount two units side-by-

side in a 1U rack space with recommended rack adapter

(see www.kramerav.com/product/KDS-DEC6).

•WP-EN6 is a wall plate encoder for a more elegant accessibility.

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Introduction

Typical Applications

KDS-EN6 / KDS-DEC6 / WP-EN6 is ideal for the following typical applications:

•Real-time essential installations such as Command and Control centers and interactive

solutions with or without KVM capabilities.

•AV distribution systems with one or more sources and many displays in schools,

universities, and public venues.

•Long-distance transmission of signals using existing wires and infrastructure in corporate

offices or government applications.

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Defining KDS-EN6

Defining KDS-EN6

Figure 1: KDS-EN6 Video Encoder Front Panel

Feature

Function

CH SELECT Buttons

Press the up or down arrow buttons to select the channel ID.

CHANNEL Display

Displays the selected channel. If the channel number exceeds 99, the

100 indicator turns on (for example, channel 124 appears as “24”).

STATUS LED

Identifies a device in a system. When sending a P3K FIND-ME

command to the system, the LED of the device to be identified flashes

for 5 seconds.

ON LED

Flashes during power up and lights when on.

LINK LED

On when a KDS-EN6 to KDS-DEC6 link is established and is

transmitting A/V signals.

Figure 2: KDS-EN6 Video Encoder Rear Panel

Feature

Function

LAN/POE RJ-45 Connector

Connect the KDS-EN6 to the network using recommended Kramer

cables. Note that this port supports power over Ethernet (PoE).

LAN LED - Green LED flashes during data transmission.

POE LED - Orange LED lights when power is supplied.

HDMI IN Connector

Connect an HDMI source.

RS-232 (Rx,Tx,Gnd)

Terminal Block Connectors

Connect to an RS-232 controller device (to control a device on the

decoder side).

IR RX on a 3.5mm Mini Jack

Connect to a receiver.

IR TX on a 3.5mm Mini Jack

Connect to an emitter.

LINE In on a 3.5mm Mini

Jack

Connect to an audio source.

RESET Button

Press to reset KDS-EN6 to its default settings.

USB Type B Port

Connect to a USB host, for example, a PC.

DC IN 24~48VDC Power

Terminal Block Connector

Connect to the Kramer power adapter (DC voltage range should be 24V

to 48V), purchased separately

(see www.kramerav.com/product/KDS-EN6).

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Defining KDS-DEC6

Defining KDS-DEC6

Figure 3: KDS-DEC6 Video Decoder Front Panel

Feature

Function

IR TX on a 3.5mm Mini Jack

Connect to an emitter.

IR RX on a 3.5mm Mini Jack

Connect to a receiver.

RESET Button

Press to reset KDS-DEC6 to its default settings.

CH Select Buttons

Press the arrow buttons up or down to select the channel ID.

CHANNEL Display

Displays the selected channel. If the channel number exceeds 99, the

100 indicator turns on (for example, channel 125 appears as “25”).

USB Type A Ports (2)

Connect to a mouse and keyboard.

STATUS LED

Identifies a device in a system. When sending a P3K

FIND-ME command to the system, the LED of the device to be

identified flashes for 5 seconds.

ON LED

Flashes during power up and lights when on.

LINK LED

On when a KDS-EN6 to KDS-DEC6 link is established and transmitting

A/V signals.

Figure 4: KDS-DEC6 Video Decoder Rear Panel

Feature

Function

LAN/POE RJ-45 Connector

Connect the KDS-DEC6 to the network using the recommended

Kramer cable. Note that this port supports power over Ethernet (PoE).

LAN LED - Green LED flashes during data transmission.

POE LED - Orange LED lights when power is supplied.

LAN RJ-45 Connector

Connect the KDS-DEC6 to the network or directly to the KDS-EN6 /

WP-EN6 using the recommended Kramer cable.

Use the LAN port (that is not used for connecting to the network or

directly to the encoder) to connect to the next KDS-DEC6 device in

a daisy chain configuration.

HDMI Out Connector

Connect to an HDMI acceptor.

RS-232 (Rx,Tx,Gnd) on

Terminal Block Connectors

Connect to an RS-232 controlled device.

L, R Audio on RCA

Connectors

Connect to a powered speaker or an amplifier.

DC IN 24~48VDC Power

Terminal Block Connector

Connect to the Kramer power adapter (DC voltage range should be 24V

to 48V), purchased separately

(see www.kramerav.com/product/KDS-DEC6).

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Defining WP-EN6

Defining WP-EN6

Figure 5: WP-EN6 Video Encoder Wall Plate

Feature

Function

IR TX on a 3.5mm Mini Jack

Connect to an emitter.

USB Type B Port

Connect to a USB host, for example, a PC.

HDMI IN Connector

Connect to an HDMI source.

IR RX on a 3.5mm Mini Jack

Connect to a receiver.

Reset Button (under wall

plate)

Press briefly to perform a software reset.

Press and hold for 10 seconds to perform a factory reset.

LINK LED

On when a WP-EN6 to KDS-DEC6 link is established and is

transmitting A/V signals.

ON LED

Flashes during power up and lights when on.

STATUS LED

Identifies a device in a system. When sending a P3K FIND-ME

command to the system, the LED of the device to be identified flashes

for 5 seconds.

CHANNEL Display

Displays the selected channel. If the channel number exceeds 99, the

100 indicator turns on (for example, channel 124 appears as “24”).

Ring Tongue Terminal

Grounding Screw

Connect to grounding wire (optional).

CONTROL RS-232 3-pin

Terminal Block Connector

(Tx, Rx and common G)

Connect to a controller to control the device.

Power Supply 2-pin Terminal

Block Connector

Connect to a power supply (if required). Connect GND to GND, +12V

to +12V.

LAN/POE RJ-45 Connector

Connect the WP-EN6 to the network using recommended Kramer

cables. Note that this port supports power over Ethernet (PoE).

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Initial Setup

Initial Setup

The KDS-EN6 / KDS-DEC6 / WP-EN6 can be powered either via PoE (using the RJ-45

LAN/POE port) if available or via a 24-48V DC power adapter.

If 24-48V DC power is connected, PoE is disabled automatically.

•Initial setup using device buttons can be performed on KDS-EN6 and KDS-DEC6

devices only.

•Initial setup using Embedded Web Pages can be performed on all devices (see Using

Embedded Web Pages on page 23).

Configuring Network Switch

To configure your network switch:

The following are recommended settings for managing the network switch to be used in your

KDS-EN6 / KDS-DEC6 / WP-EN6 installation.

1. Assign the switch to an IP address.

2. Set your switch to the following:

▪Jumbo Frames –On.

▪IGMP Snooping –On.

▪IGMP Querier –On.

▪IGMP Immediate/Fast Leave –Off.

Kramer Electronics Ltd.

KDS-EN6 / KDS-DEC6 / WP-EN6 –Initial Setup

Initial Setup Using Device Buttons

The device default IP address is written on the bottom of the device.

To avoid conflicts with multiple devices and allow web page control for each device, it is

important to change each device’s IP address

Setting KDS-EN6 / KDS-DEC6 IP Address

To set the KDS-EN6 / KDS-DEC6 IP address:

1. Connect the KDS-EN6 / KDS-DEC6 LAN/POE RJ-45 port to your network (if your

network does not support PoE, connect a 24-48V DC power adapter).

The ON LED lights green and the LINK LED flashes (indicating that no streaming activity

is detected).

2. Press and hold for 3 seconds.

3. Press or to select DH (DHCP) or SC (static) IP address setup.

When setting to DHCP we recommend that you contact your IT administrator for

setting the system IP addresses.

▪If you selected DHCP on a KDS-DEC6 device, press and hold or for 3 seconds

to save your selection.

The channel display flashes “--” 3 times and the device reboots.

▪If you selected DHCP on a KDS-EN6 device, the channel display flashes “ID” 3

times.

▪If you selected Static for either device, press and hold or for 3 seconds to save

your selection.

The channel display flashes “IP” 3 times and the device reboots.

4. Press or to set the IP address.

You can only define the last three digits of the IP address when setting the IP

address via the channel buttons. To change the entire IP address, go to Setting IP

Address on page 24.

5. Press and hold and for 3 seconds to save your selection.

The KDS-EN6 channel number can be set immediately after the IP address is set.

Andere Handbücher für KDS-EN6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kramer Medienkonverter Handbücher

Kramer

Kramer VA-40 Bedienungsanleitung

Kramer

Kramer VP-791 Bedienungsanleitung

Kramer

Kramer MV-6 Bedienungsanleitung

Kramer

Kramer VM-24HDMI Bedienungsanleitung

Kramer

Kramer 401C Bedienungsanleitung

Kramer

Kramer ACC3-12-SP Bedienungsanleitung

Kramer

Kramer VM-1010 Bedienungsanleitung

Kramer

Kramer VP-503XL Bedienungsanleitung

Kramer

Kramer FC-31xl Bedienungsanleitung

Kramer

Kramer FC-10Dxl Bedienungsanleitung

Kramer

Kramer VP-440H2 Bedienungsanleitung

Kramer

Kramer KDS-SW3-EN7 Bedienungsanleitung

Kramer

Kramer VP-437xl Bedienungsanleitung

Kramer

Kramer 6808HDxl Bedienungsanleitung

Kramer

Kramer DigiTOOLS 7408 Bedienungsanleitung

Kramer

Kramer FC-31 Bedienungsanleitung

Kramer

Kramer TOOLS VP-100 Bedienungsanleitung

Kramer

Kramer VP-701XL Bedienungsanleitung

Kramer

Kramer KDS-100EN Bedienungsanleitung

Kramer

Kramer VM-4Hxl Bedienungsanleitung

Kramer

Kramer VP-441 Bedienungsanleitung

Kramer

Kramer WP-SW2-EN7 Bedienungsanleitung

Kramer

Kramer VM-127 Bedienungsanleitung

Kramer

Kramer VP-483 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung