Kramer 691 Bedienungsanleitung

691/692 Quick Start

P/N:

2900- 301392QS

Rev:

Scan for full manual

691/692 Quick Start Guide

This guide helps you installand use your 691/692 for thefirst time.

Go to www.kramerav.com/downloads/691 or www.kramerav.com/downloads/692 to download the latest

user manual and check if firmware upgrades are available.

Step 1: Check what’s in the box

691 HDBT 2.0 Transmitter or

692 HDBT 2.0 Receiver

1 OSP-MM1 Fiber Optic SFP+ Transceiver

1 Quick start guide

1 Power adapter and cord

4 Rubber feet

Step 2: Get to know your 691/692

691

Feature

Function

USB Connector

Connect to the USB host (for example, a laptop) for traffic extension to remote

connected USB devices.

LINK LED

Lights green when the HDBT link is active.

IN LED

Lights green when an active HDMI source is connected.

ON LED

Lights green when the device receives power.

HDMI IN Connector

Connect to the HDMI source.

IR 3.5mm Mini Jack Connector

Connect to an external infrared transmitter or receiver for traffic extension.

RS-232 3-pin Terminal Block

Connect to an RS-232 controller for traffic extension (for example, a PC to control

the projector).

AUDIO IN 3.5mm Mini Jack

Connect to the stereo, analog audio source.

OUT IN SFP+ Connector

Connect the fiber optic cable to the OUT IN SFP+ connectors (OSP-MM1 included).

SETUP 4-way DIP-switch

Sets the device functions.

CONTROL

RS-232 3-pin Terminal

Block

Connect to the serial controller to control this device.

ETHERNET RJ-45

Connector

Connect to the LAN to extend network traffic to the receiver and Ethernet controller

to control this device.

RESET Switch

Press and hold for 5 seconds to reset the device to factory default settings.

Press and immediately release to power-cycle the device (Reset).

PROG Mini USB Connector

Connect to a PC to perform firmware upgrades.

12V DC Power Connector

Connect to the supplied power adapter.

692

Feature

Function

USB Connectors

Connect to the USB devices (for example, a camera, keyboard, mouse and so on)

for traffic extension to a remote connected USB host.

LINK LED

Lights green when the HDBT link is active.

ON LED

Lights green when the device receives power.

HDMI OUT Connector

Connect to the HDMI acceptor.

IR 3.5mm Mini Jack Connector

Connect to an external infrared transmitter or receiver for traffic extension.

RS-232 3-pin Terminal Block

Connect to an RS-232 Controller for traffic extension (for example, a PC to control

the Blu-ray player on the transmitter side).

AUDIO OUT 3.5mm Mini Jack

Connect to the stereo, analog audio acceptor.

OUT IN SFP+ Connector

Connect the fiber optic cable to the OUT IN SFP+ connectors (OSP-MM1 included).

SETUP 4-way DIP-switch

Sets the device functions.

CONTROL

RS-232 3-pin Terminal

Block

Connect to the serial controller to control this device.

ETHERNET RJ-45

Connector

Connect to the LAN to extend network traffic to the transmitter and Ethernet

controller to control this device.

RESET Switch

Press and hold for 5 seconds to reset the device to factory default settings.

Press and immediately release to power-cycle the device (reset).

PROG Mini USB Connector

Connect to a PC to perform firmware upgrades.

12V DC Power Connector

Connect to the supplied power adapter.

Step 3: Mount 691/692

Install 691/692 using one of the following methods:

•Attach the rubber feet and place the unit on a flat surface.

•Fasten a bracket (included) on each side of the unit and attach it to a flat surface

(see www.kramerav.com/downloads/691).

•Mount the unit in a rack using the recommended rack adapter

(see www.kramerav.com/product/691).

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

•Maximum mounting height for the device is 2 meters.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your 691/692. For best results, we recommend

that you always use Kramer high-performance cables to connect AV equipment to the 691/692.

For optimal performance, use the RECOMMENDED Kramer cables available at www.kramerav.com/product/691.

Using third-party cables may cause damage!

To install/replace the OSP-MM1 or other Kramer recommended

SFP+ transceiver:

1. Pull the bail out and remove the currently installed transceiver,

insert the protective cap and store in a safe place.

2. Make sure the bail of the new transceiver is pushed up, in the

closed position.

3. Insert the new transceiver into the relevant optical device SFP+

slot and push it in until it clicks.

4. Remove the protective cap and store it in a safe place for future

use.

Warning: Connecting the OSP SFP+ connector to an LC(APC) fiber

connector may cause poor performance and damagethe connector!

Refer to www.kramerav.com/downloads/691 for more information.

Warning: Class 1 Laser Product

•Invisible laser radiation present.

•Avoid long-term viewing of laser.

•Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes

and magnifying lenses, but not spectacles or contact lenses).

•Avoid placing optical devices in the emitted beam that could cause the concentration of the laser

radiation to be increased.

SETUP DIP-Switches

A DIP-switch that is down is on, up is off. Changes to the DIP-switches only take effect on power-up. After

changing a switch, reboot the device.

Function

Applicable to:

Status

For future use

691 and 692

—

Audio source priority

691 only

Off—Embedded audio (factory default)

On—Analog audio

EDID lock

691 and 692

Off—Automatic EDID acquisition (factory default)

On—Lock (locks the current EDID so that changes on the

output do not result in changes to the EDID)

Audio mode selection

691 only

Off—Auto (factory default)

On—Manual

Step 5: Connect power

Connect the power cord to 691/692 and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

Step 6: Operate 691/692

Embedded Web pages:

RS-232 and Ethernet parameters and defaults:

RS-232

Protocol 3000

Baud Rate:

115,200

Stop Bits:

Data Bits:

Parity:

None

Command format:

ASCII

Example (get device model name):

#model?<cr>

TCP/IP

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.000.000

TCP Port #:

5000

Default gateway:

192.168.0.1

Embedded Webpages Authentication

User/Password

Admin/Admin

Full Factory Reset

Rear panel

button:

Press and hold for 5 seconds to reset the device to factory default

settings.

P3K command:

#factory<cr>

Embedded Web

pages:

Select Device Settings page and click Factory reset

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Andere Handbücher für 691

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kramer Empfänger Handbücher