Kramer TP-583T Bedienungsanleitung

TP-583T, TP‑583R Quick Start

P/N:

2900- 301158QS

Rev:

Scan for full manual

TP-583T/TP-583R Quick Start Guide

This guide helps you install and use your TP-583T/TP-583R for the first time.

Go to www.kramerav.com/downloads/TP-583T, TP-583R to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

TP-583T HDMI Line Transmitter or

1 Power adapter and cord

1 Quick start guide

TP-583R HDMI Line Receiver

4 Rubber feet

1 Bracket set

Step 2: Get to know your TP-583T and TP-583R

TP-583T

Feature

Function

IN LED

Lights green when an active source device input signal is detected.

OUT LED

Lights green when an active, far-end sink (acceptor) connection is detected via the

HDBT link.

LINK LED

Lights green when an HDBT link is established with the HDBaseT receiver.

ON LED

Lights green when the device receives power.

LINE RJ-45 Connector

Connect to the RJ-45 HDBT LINE connector on a receiver (for example, TP-583R, TP-

780R and so on).

HDMI™ IN Connector

Connect to an HDMI source.

SETUP DIP-switches

Set the operation DIP-switches.

RS-232 (G, Rx, Tx) 3-pin

Terminal Block Connector

Connect to a laptop to control the receiver or perform firmware upgrade.

Connect to a controller device (for example, SL-240C) to serially control a remote

device (for example, the HDMI OUT acceptor) that is connected to TP-583R.

IR 3.5mm Mini Jack Connector

Connect to an external infrared emitter / sensor.

12V DC Power Connector

12V DC connector for powering the unit.

TP-583R

Feature

Function

IN LED

Lights green when an active, far-end source device input signal is detected via the

HDBT link.

OUT LED

Lights green when an active sink (acceptor) connection is detected.

LINK LED

Lights green when an HDBT link is established with the HDBaseT transmitter.

ON LED

Lights green when the device receives power.

LINE RJ-45 Connector

Connect to the RJ-45 HDBT LINE connector on a transmitter (for example, TP-583T,

TP-780T and so on).

HDMI® OUT Connector

Connect to an HDMI acceptor.

SETUP DIP-switches

Set the operation DIP-switches.

RS-232 (G, Rx, Tx) 3-pin

Terminal Block Connector

Connect to a laptop to control the receiver or perform firmware upgrade.

Connect to a serially controlled device (for example, the HDMI OUT acceptor) to enable

its control by a remote controller device (for example, SL-240C) that is connected to

TP-583T.

IR 3.5mm Mini Jack Connector

Connect to an external infrared emitter / sensor.

12V DC Power Connector

12V DC connector for powering the unit.

Step 3: Install TP-583T/TP-583R

Install TP-583T/TP-583R using one of the following methods:

Attach the rubber feet and place the unit on a flat surface.

Fasten a bracket (included) on each side of the unit and attach it to a flat surface. For more

information go to www.kramerav.com/downloads/TP-583T, TP-583R.

Mount the unit in a rack using the recommended rack adapter (see

www.kramerav.com/product/TP-583T, TP-583R).

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your TP-583T/TP-583R. For best results, we recommend

that you always use Kramer high-performance cables to connect AV equipment to TP-583T/TP-583R.

RJ-45 Pinout:

For HDBT cables, it is recommended that the cable

ground shielding be connected/soldered to the

connector shield:

PIN EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

For optimum range and performance use the recommended Kramer cables available at

www.kramerav.com/product/TP-583T, TP-583R.

DIP-Switch Settings

The DIP-switches are used to:

•Set the compression levels and resolutions.

•Enable RS-232 signal extension.

•Upgrade the firmware.

•Determine IR signal pass-through.

All the DIP-switches are set to OFF (up) by default.

To use your TP-583T or TP-583R with any other standard HDBaseT

extender (without compression), verify that DIP-switch 1B is OFF (up).

A –DIP-switch Settings

Feature

DIP-switch Settings

Reserved

Set to OFF (up).

Set the Compression Level

(for extended range)

OFF (up) –Standard compression level.

ON (down) –High compression level for additional extension.

B –DIP-switch Settings

Changes to DIP-switches 2B and 3B only take effect after power cycling the device.

Feature

DIP-switch Settings

Define Compressed

Resolutions

OFF (up) –Compress signal resolutions higher than 1080p.

ON (down) –Compress all signal resolutions to enable extended reach.

2B, 3B

Define RS-232 Function

OFF (up), OFF (up) –Embed RS-232 data and control signals over the

extension line.

Other DIP-switch settings are reserved for firmware upgrade.

For further details, contact [email protected].

Define IR Pass-through

OFF (up) –Pass-through the IR signal to the IR port via IR cable.

ON (down) –Add IR modulation to the IR output signal (applies only when

the IR port is connected to an IR emitter cable).

The IR Pass-through DIP-switch setup depends on the IR

control configuration. We recommend that you test which

position best suits your application.

Step 5: Connect the power

Connect the 12V DC power adapter to TP-583T/TP-583R and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power adapter that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Andere Handbücher für TP-583T

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kramer Empfänger Handbücher

Kramer

Kramer WP-120 Bedienungsanleitung

Kramer

Kramer TOOLS TP-220HD Bedienungsanleitung

Kramer

Kramer VP-427H2 Bedienungsanleitung

Kramer

Kramer 631T Bedienungsanleitung

Kramer

Kramer PT-110-od Bedienungsanleitung

Kramer

Kramer PT-110 Bedienungsanleitung

Kramer

Kramer TP-31 Bedienungsanleitung

Kramer

Kramer 713 Bedienungsanleitung

Kramer

Kramer TP-305A Bedienungsanleitung

Kramer

Kramer TP-780TXR Bedienungsanleitung

Kramer

Kramer 673T Bedienungsanleitung

Kramer

Kramer TOOLS TP-45 Bedienungsanleitung

Kramer

Kramer 670T Bedienungsanleitung

Kramer

Kramer VP-427H2 Bedienungsanleitung

Kramer

Kramer KWC-MUSB Bedienungsanleitung

Kramer

Kramer PT-871 Bedienungsanleitung

Kramer

Kramer TP-551HDCP Bedienungsanleitung

Kramer

Kramer 602T Bedienungsanleitung

Kramer

Kramer 690R Bedienungsanleitung

Kramer

Kramer VM-1H4C Bedienungsanleitung

Kramer

Kramer WP-561 Bedienungsanleitung

Kramer

Kramer TP-590Rxr Bedienungsanleitung

Kramer

Kramer DigiTOOLS TP-551 Bedienungsanleitung

Kramer

Kramer 708 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung

Dish Network

Dish Network Satellite Television Bedienungsanleitung