Kramer VP-440H2 Bedienungsanleitung
VP-440H2 Quick Start
P/N:
2900- 300930QS
Rev:
4
Scan for full manual
VP-440H2 Quick Start Guide
This guide helps you install and use your VP-440H2 for the first time.
Go to www.kramerav.com/downloads/VP-440H2 to download the latest user manual and
check if firmware upgrades are available.
Step 1: Check what’s in the box
VP-440H2 4K Presentation Switcher / Scaler
1 Power cord
4 Rubber feet
1 Power supply (48V DC)
1 Quick start guide
Step 2: Get to know your VP-440H2
#
Feature
Function
1
48 V () Slide Switch
Slide up (48V) to select a condenser type microphone; slide down to select a dynamic
type microphone (we recommend that you slide down if a microphone is not connected to
the VP-440H2).
2
MIC 6.3mm Jack
Connect to the microphone source.
3
Input Selector
Buttons
HDBT IN
Press to select the HDBT input.
4
HDMI IN
Press to select the HDMI input (from 1 to 3).
5
PC IN
Press to select the computer graphics input.
6
MENU Button
Displays the OSD menu.
7
Navigation
Buttons
Press to decrease numerical values or select from several definitions.
When not in the OSD menu, press to reduce the output volume.
Press to move up the menu list values.
Press to increase numerical values or select from several definitions.
When not in the OSD menu, press to increase the output volume.
Press to move down the menu list.
ENTER
Press to accept changes and change the SETUP parameters.
8
RESET TO XGA/1080p Button
Press and hold for about 5 seconds to toggle the output resolution between XGA and
1080p, alternatively.
9
PANEL LOCK Button
Press and hold for about 5 seconds to lock/unlock the front panel buttons.
#
Feature
Function
10
CONTROL (Tx, Rx, GND) Terminal
Block Connectors
Connect to the PC or the serial controller to control the device.
11
HDBT IN (Tx, Rx, GND) Terminal
Block Connectors
Connect to a controller to control peripheral devices that are connected to the
HDBT transmitter (for example, a Blu-ray player connected to WP-20).
12
HDBT OUT (Tx, Rx, GND) Terminal
Block Connectors
Connect to a controller to control peripheral devices that are connected to the
HDBT receiver (for example, a projector connected to TP-580Rxr).
13
AUDIO INPUT
Unbalanced
Stereo 3.5 Mini
Jack
HDMI
Connect to the analog audio HDMI source (from 1 to 3).
14
PC
Connect to the analog audio computer graphics source.
15
AUDIO OUT 3.5 Mini Jack
Connect to an unbalanced stereo audio acceptor.
16
ETHERNET Connector
Connects to the PC or other controller through computer networking.
17
VIDEO INPUT
Connectors
HDBT IN RJ-45
Connect to an HDBT transmitter (for example, WP-20).
Can supply PoE (up to 13W) to the transmitter.
18
HDMI IN
Connect to the HDMI source (from 1 to 3).
19
PC IN on15-pin
HD
Connect to the computer graphics source.
20
HDBT OUT RJ-45 Connector
Connect to an HDBT receiver (for example, TP-580Rxr).
21
HDMI OUT Connector
Connect to the HDMI acceptor.
22
48V DC Power Terminal Block
+48V DC connector for powering the unit.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Step 3: Install VP-440H2
Install VP-440H2 using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/VP-440H2)
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VP-440H2. For best results, we recommend that
you always use Kramer high-performance cables to connect AV equipment to VP-440H2.
RJ-45 Pinout:
Microphone Pinout:
For the Ethernet connector, see the wiring
diagram below
The microphone 6mm jack pinout for a condenser microphone
The microphone 6mm jack pinout for a dynamic microphone.
PIN EIA /TIA 568B
PIN
Wire Color
1
Orange /
White
2
Orange
3
Green / White
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
For optimum range and performance use the recommended Kramer cables available at
www.kramerav.com/product/VP-440H2.
For HDBT cables, it is recommended that the cable ground shielding be connected/soldered to the connector
shield.
Step 5: Connect the power
Connect the power cord to VP-440H2 and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.
Step 6: Control and operate VP-440H2 via the front panel buttons and via
Web pages:
OSD Menu:
Menu
Menu Items
Picture
Adjust contrast brightness and color and fine-tune the image.
Input
Select input source.
Output
Select method for 4K input to 4K output handling, image size and
resolution.
Audio
Select audio source, audio parameters (bass, treble and so on),
microphone settings and volume per input.
OSD
Set OSD position, transparency and so on.
Advanced
Select HDCP on each of the inputs and outputs, manage the EDID and
define IP settings.
Info.
View device information.
Factory
Reset to factory default settings.
Andere Handbücher für VP-440H2
2
Andere Kramer Schalten Handbücher
Kramer
Kramer VP-444 Bedienungsanleitung
Kramer
Kramer VS-211HA Bedienungsanleitung
Kramer
Kramer VP-8x8 Bedienungsanleitung
Kramer
Kramer VS-41HDCP Bedienungsanleitung
Kramer
Kramer VS-120 Bedienungsanleitung
Kramer
Kramer VM-4HDxl Bedienungsanleitung
Kramer
Kramer VS-211H2 Bedienungsanleitung
Kramer
Kramer VP-24 Bedienungsanleitung
Kramer
Kramer VS-211HDx1 Bedienungsanleitung
Kramer
Kramer VP-211N Bedienungsanleitung
Kramer
Kramer VP-734 Bedienungsanleitung
Kramer
Kramer WP-20CT Bedienungsanleitung
Kramer
Kramer PT201VGA Bedienungsanleitung
Kramer
Kramer VS-2016 Bedienungsanleitung
Kramer
Kramer VM-1H4C Bedienungsanleitung
Kramer
Kramer VM-218DTxr Bedienungsanleitung
Kramer
Kramer VP-774A Bedienungsanleitung
Kramer
Kramer VP-438 Bedienungsanleitung
Kramer
Kramer WP-501 Bedienungsanleitung
Kramer
Kramer DigiTOOLS VS-41USB Bedienungsanleitung
