Kramer VP-734 Bedienungsanleitung
VP-734 Quick Start
P/N:
2900- 301068QS
Rev:
6
Scan for full manual
VP-734 Quick Start Guide
This guide helps you install and use your VP-734 for the first time.
Go to www.kramerav.com/downloads/VP-734 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
VP-734 Presentation Switcher/Scaler
1 Set of rack ears
4 Rubber feet
Remote control transmitter with batteries
1 Power cord
1 Quick start guide
2 C-GM/3RVF-1 cables
Step 2: Get to know your VP-734
# Feature Function
1
IR Sensor
Receives signals from the remote control transmitter.
IR LED
Lights red when the unit accepts IR remote commands.
2
INPUT Selector
Buttons
(illuminate green
when selected)
UNIV. 1
Press to select the analog video (VGA / component / composite / s-Video) source
(configured via the OSD menu), and the appropriate audio source (from 1 to 2).
3
HDMI™ 1
Press to select the HDMI source (from 1 to 4).
4
DP
Press to select the DP source.
5 Program BLANK Button Press to toggle between a blank screen (blue or black) and the program display.
The BLANK button can be programmed to mute the audio signal at the same time.
6
Program FREEZE Button
Press to freeze/unfreeze the program output video image. The FREEZE button can be
programmed to mute the audio signal at the same time.
7
MENU Button
Press to display the OSD menu screen. Press again to return to normal operation.
8
ENTER Button
Press to move to the next level in the OSD screen or to accept a new parameter.
Button Decreases the range by one step in the OSD screen or moves to the previous level in
the OSD screen.
Decreases the volume level, when not in the OSD menu.
Button Moves up one step (in the same level) in the OSD screen or moves to the previous slide
when running a slideshow.
Button
Increases the range by one step in the OSD screen.
Increases the volume level, when not in the OSD menu.
Button
Moves down one step (in the same level) in the OSD screen or moves to the next slide
when running a slideshow.
9
RESET TO XGA/720p Button
Press and hold to reset to the default resolution (toggles between RESET TO XGA and
720p).
10
PANEL LOCK Button
Press to lock/unlock the front panel to prevent unintentional operation
11
USB Connector
Connects to a USB drive to download a Logo and save settings.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
# Feature Function
12
UNIV 1 IN 15-pin HD Connector
Connect to the universal source (as computer graphics, composite video,
s-Video or component video), from 1 to 2.
13
HDMI 1 IN Connector
Connect to the HDMI 1 source (from 1 to 4).
14
DP IN DisplayPort Connector
Connect to the DP source.
15 CONFIGURABLE AUDIO INPUTS on 3.5
Mini Jack Connectors
Connect to the unbalanced stereo analog audio sources from 1 to 7.
16
AUDIO LINE OUT 5-pin Terminal Block
Connect to the balanced stereo analog audio acceptor.
17
VIDEO
OUTPUTS
HDMI 1 Connector
Connect to an HDMI acceptor.
18
PC 15-pin HD Connector
Connect to a computer graphics acceptor.
19
ETHERNET Port
Connect to your LAN.
20
RS-232 9-pin D-sub Connector
Connect to PC or Serial Controller.
21
SPKR OUT 4-pin Terminal Block
Connect to a pair of loudspeakers.
22
S/PDIF IN 3.5 Mini Jack Connector
Connect to a digital audio source.
23
S/PDIF OUT 3.5 Mini Jack Connector
Connect to a digital audio acceptor.
24
Mains Power Connector
Connect to the mains power.
25
Mains Power Fuse
Fuse for protecting the device.
Step 3: Install the VP-734
To rack mount the machine attach both ear brackets (by removing the screws from each side
of the machine and replacing those screws through the ear brackets) or place the machine
on a table.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VP-734. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the VP-734.
Connect the audio output
To a balanced
stereo audio
acceptor:
To an
unbalanced
stereo audio
acceptor:
Universal connector pinout
PIN # VGA COMP s-Video CV
1
R
Pr
2
G
Y
Y
Composite video
3
B
Pb
C
9
+5VD
12
EDID_SDA
13
H_Sync
14
V_Sync
15
EDID_SCL
Note that PINs 5, 6, 7, 8 and 10 are GND
Step 5: Connect the power
Connect the power cord to VP-734 and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the power cord that is supplied with the unit.
Warning:
Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information
Step 6: Operate the VP-734
Operate VP-734 via:
•Front panel buttons
•OSD menu
•Remotely, by RS-232 serial
commands transmitted by a
touch screen system, PC, or
other serial controller
•Remotely, using the IR remote
control transmitter
•Embedded web pages via the
Ethernet
RS-232 Control / Protocol 3000
Baud Rate:
115,200
Data Bits:
8
Stop Bits:
1
Parity:
None
Command Format:
ASCII
Example (switch input to UNIV2): Y 0 92 1<CR>
Default Ethernet Parameters
IP Address:
192.168.1.39
Subnet mask:
255.255.255.0
Gateway:
192.168.1.254
TCP Port #:
5000
Maximum TCP Ports:
1
Full Factory Reset
OSD
Go to: Menu-> Setup -> Factory Reset -> press Enter to
confirm
Front panel buttons Press the Reset to XGA/720p Button while plugging the
power to reset the machine
Technical Specifications
Inputs
2 Universal (VGA, Composite, s-Video
and Component)
On 15-pin HD connectors
4 HDMI
On female HDMI connectors
1 DP
On a female DisplayPort connector
1 S/PDIF
On an RCA connector
7 Unbalanced Stereo Audio
On 3.5mm mini jack connectors
Outputs
1 HDMI
On a female HDMI connector
1 PC
On a 15-pin HD connector
1 Balanced Stereo Audio
On a 5-pin terminal block connector (+4dBu nominal)
1 stereo speaker
On a 4-pin large terminal block (10W per channel into 8Ω)
1 digital S/PDIF output
on an RCA connector
Ports
Ethernet
On an RJ-45 female connector
RS-232
On a 9-pin D-sub connector
USB
On a USB connector
Video
Compliance
HDMI and HDCP
Output Resolutions Native HDMI, Native VGA, 640x480x60Hz, 640x480x75Hz,
800x600x50Hz, 800x600x60Hz, 800x600x75Hz,
1024x768x50Hz, 1024x768x60Hz, 1024x768x75Hz,
1280x768x50Hz, 1280x768x60Hz, 1280x720x60Hz,
1280x800x60Hz, 1280x1024x50Hz, 1280x1024x60Hz,
1280x1024x75Hz, 1366x768x50Hz, 1366x768x60Hz,
1400x1050x50Hz, 1400x1050x60Hz, 1600x900x60Hz (R),
1600x1200x50Hz, 1600x1200x60Hz, 1680x1050x60Hz,
1920x1080x60Hz, 1920x1200x60Hz (R), 2048x1080x50Hz,
2048x1080x60Hz, 3840x2160@24Hz, 3840x2160@25Hz,
3840x2160@29.97Hz, 3840x2160@30Hz,
4096x2160@24Hz, 480px60Hz, 576px50Hz, 720px50Hz,
720px60Hz, 1080ix50Hz (1080i/1080px50Hz), 1080ix60Hz
(1080i/1080px60Hz), 1080px50Hz, 1080px60Hz,
1080px24Hz, 480px59.94Hz, 720px59.94Hz,
1080ix59.94Hz (1080i/1080px59.94Hz), 1080px23.98,
1080px29.97, 1080px59.94, Custom 1 to Custom 4
Controls Front Panel
Input selection buttons, blank, freeze, lock and reset
resolution buttons
Menu buttons to access OSD menu
Remote
RS-232
Ethernet
Web pages
IR remote control transmitter
Power
Consumption
100-240V AC, 38VA max.
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory
Compliance
Safety
CE, FCC, UL
Environmental
RoHs, WEEE
Enclosure
Size
19”, 1U
Type
Aluminum
Cooling
Fan ventilation
General
Net Dimensions (W, D, H)
43.6cm x 23.7cm x 4.4cm (17.18" x 9.3" x 1.72")
Shipping Dimensions (W, D, H)
52.5cm x 33cm x 10.7cm (20.7" x 13" x 4.21")
Net Weight
2.5kg (5.5lbs) approx.
Shipping Weight
3.4kg (7.5lbs) approx.
Accessories
Included
Rack ears, IR remote control, power cord, 2 C-GM/3RVF-1
Specifications are subject to change without notice. Go to our Web site at www.kramerav.com to access the list of resolutions.
Andere Handbücher für VP-734
3
Andere Kramer Schalten Handbücher
Kramer
Kramer VS-211H2 Bedienungsanleitung
Kramer
Kramer VS-41H Bedienungsanleitung
Kramer
Kramer VP-23xl Bedienungsanleitung
Kramer
Kramer VM-37 Bedienungsanleitung
Kramer
Kramer RC-10TBB Bedienungsanleitung
Kramer
Kramer VP-550X Bedienungsanleitung
Kramer
Kramer VP-81SIDN Bedienungsanleitung
Kramer
Kramer VS-24xl Bedienungsanleitung
Kramer
Kramer VS-161H Bedienungsanleitung
Kramer
Kramer VS-411UHD Bedienungsanleitung
Kramer
Kramer VP-720DS Bedienungsanleitung
Kramer
Kramer VS-55 Bedienungsanleitung
Kramer
Kramer VS-21H-IR Bedienungsanleitung
Kramer
Kramer VM-3H2 Bedienungsanleitung
Kramer
Kramer VS-81H Bedienungsanleitung
Kramer
Kramer VP-794 Bedienungsanleitung
Kramer
Kramer VP-23N Bedienungsanleitung
Kramer
Kramer VS-801USB Bedienungsanleitung
Kramer
Kramer VP-740 ProScale Bedienungsanleitung
Kramer
Kramer VP-558 Bedienungsanleitung
