Kramer EXT3-C-WP-XR-T Bedienungsanleitung
EXT3-C-WP-XR-T Quick Start
P/N:
2900- 301598QS
Rev:
1
Scan for full manual
EXT3-C-WP-XR-T Quick Start Guide
This guide helps you install and use your EXT3-C-WP-XR-T for the first time.
Go to www.kramerav.com/downloads/EXT3-C-WP-XR-T to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
EXT3-C-WP-XR-T 4K60 USB C Transmitter
1 Upper front panel
1 Screw set
1 Power cord and adapter
1 Lower front Panel
1 Quick start guide
1 Multi signal USB-C cable (1m)
Step 2: Get to know your EXT3-C-WP-XR-T
#
Feature
Function
1
USB-C IN Connector
Connect to a USB-C AV source (that supports DisplayPort Alternate Mode) for AV input,
USB host connection to local and remote connected USB devices. Charges sources (that
support USB Power Delivery 2.0) up to 60W when the device is powered via the power
adapter). While charging, the charging icon (to the right of the connector) becomes visible
and lights orange.
2
LOOP HDMI Connector
Connect to a local acceptor to view the AV signal coming from the USB-C IN input.
3
USB A 2.0 Charging Connector 1
Connect to the USB local peripheral devices (for example, a keyboard & mouse). When
USB Host PC is disconnected, the USB signal and charging power for this port are
inactive.
USB A 2.0 Charging Connector 2
Connect to the USB local peripheral devices (for example, a USB camera, a soundbar,
microphone and so on). When USB Host PC is disconnected, the USB charging power
for this port continues to be active.
4
IN LED
Lights blue when an active AV input signal is detected from the source device that is
connected to the USB-C IN port.
5
OUT LED
Lights blue when an HDMI output device is detected on the receiver side.
6
LOOP LED
Lights blue when an active signal is transmitted on the HDMI LOOP port.
#
Feature
Function
7
HOST LED
Lights orange when the USB is set to Host.
8
LINK LED
Lights green when the HDBT connection is active.
9
STATUS LED
Lights green when PSU powered and orange when PoE powered.
10
DISPLAY ON Button
Press to toggle power on/off the remote CEC-enabled display that is connected to the
receiver side. Button LED lights blue when remote display power is on.
11
Ring Tongue Terminal Grounding
Screw
Connected to grounding wire.
12
HDBT OUT PoE RJ-45 Connector
Connect to the HDBT IN RJ-45 connector on a receiver (for example,
EXT3-POE-XR-R). Receives PoE (PD).
13
1G LAN RJ-45 Connector
Connect to a LAN to provide Network and Internet to the source device that is connected
to the USB-C IN port and/or Ethernet extension to the receiver.
14
RS-232 3-pin Terminal Block
Connector
Connect to a controller device (for example, SL-240C) to control a remote device via
serial connection (for example, the remotely connected PTZ USB camera).
15
IR OUT 2-pin Terminal Block
Connector
Outputs a received IR signal (from a controller) to a connected IR emitter.
16
20V DC
+20V DC 6A connector for powering the unit and charging the connected input device to
USB-C.
Setting the DIP-Switches
DIP-Switch Settings
To access the EXT3-C-WP-XR-T DIP-switches
remove the top front panel.
By default, DIP-Switch 2 is set to ON (up)
while all the other DIP-switches are set to
OFF (down) by default.
Setting EXT3-C-WP-XR-T to USB host requires
device reset (disconnecting and then reconnecting
the power).
We recommend that you set the device to host (if
required) before mounting.
DIP #
Feature
DIP-switch Settings
1
TBD
2
Fan FW upgrade
OFF (down) –For factory use only
ON (up) –Mandatory for normal operation (default).
3
Eth FW upgrade
OFF (down) –Mandatory for normal operation (default).
ON (up) –For factory use only.
4
Active USB Host
OFF (down) –USB-C is activated as a HOST for the connected USB
devices (default).
ON (up) –USB-C is activated as a USB device.
5
IR Modulation
OFF (down) –IR pass-thru is enabled (default).
On –IR pass-thru is disabled (add a 38KHz modulation to the IR output
signal).
6
RS-232 Extension
Off (down) –Mandatory for serial extension (default).
On (up) –For factory use only.
Step 3: Install the EXT3-C-WP-XR-T
Insert the device into the in-wall box (note that first you need to connect the HDBT cable and power) and connect the parts as
shown in the illustration below.
When installing the device, take care not to obstruct the upper and lower ventilation holes.
US-D Version
US model panel size is compatible with DECORA® design frame size.
DECORA® is a registered trademark of Leviton Manufacturing Co., Inc.
We recommend that you use any 2 gang US electrical junction box.
Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your EXT3-C-WP-XR-T.
This section defines the HDBT pinout, using a straight pin-to-pin cable with
RJ-45 connectors.
EIA /TIA 568B
PIN
Wire Color
1
Orange / White
It is recommended that the cable ground shielding be
connected/soldered to the connector shield.
2
Orange
3
Green / White
4
Blue
To achieve specified extension distances, use the recommended
Kramer cables available at
www.kramerav.com/product/EXT3-C-WP-XR-T.
Using third-party cables may cause damage!
5
Blue / White
6
Green
7
Brown / White
8
Brown
Step 5: Connect power
If not powered by PoE, connect the power adaptor to the EXT3-C-WP-XR-T and the power cord and plug it into the mains
electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Andere Kramer Sender Handbücher
Kramer
Kramer 622T Bedienungsanleitung
Kramer
Kramer TP-581T Bedienungsanleitung
Kramer
Kramer TP-15 Bedienungsanleitung
Kramer
Kramer 691 Bedienungsanleitung
Kramer
Kramer DIP-20 Bedienungsanleitung
Kramer
Kramer 617T Bedienungsanleitung
Kramer
Kramer TP-112HD Bedienungsanleitung
Kramer
Kramer VP-200XLT Bedienungsanleitung
Kramer
Kramer TP-583T Bedienungsanleitung
Kramer
Kramer VP-200XLTHD Bedienungsanleitung
Kramer
Kramer TP-121EDID Bedienungsanleitung
Kramer
Kramer SID-X1N Bedienungsanleitung
Kramer
Kramer DigiTOOLS KW-11T Bedienungsanleitung
Kramer
Kramer TWA Bedienungsanleitung
Kramer
Kramer TP-112HD Bedienungsanleitung
Kramer
Kramer 610R Bedienungsanleitung
Kramer
Kramer TP-590Txr Bedienungsanleitung
Kramer
Kramer 611T Bedienungsanleitung
Kramer
Kramer WP-110xl Bedienungsanleitung
Kramer
Kramer TOOLS TP-104 Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
