KROHNE OPTISWITCH 3000 C Bedienungsanleitung

Operating Instructions

OPTISWITCH 3000 C

with two-wire output

Contents

1About this document

1.1Function ............................. 4

1.2Target group .......................... 4

1.3Symbolism used ....................... 4

2For your safety

2.1Authorised personnel .................... 5

2.2Appropriate use........................ 5

2.3Warning about misuse ................... 5

2.4CE conformity ......................... 5

3Product description

3.1Conﬁguration.......................... 6

3.2Principle of operation.................... 6

3.3Operation ............................ 7

3.4Storage and transport ................... 7

4Mounting

4.1General instructions..................... 9

4.2Mounting instructions.................... 10

5Connecting to voltage supply

5.1Preparing the connection ................. 13

5.2Connection steps....................... 13

5.3Wiring plan,single chamber housing......... 14

6Set up

6.1General.............................. 16

6.2Adjustment elements .................... 17

6.3Function chart ......................... 18

7Maintenance and fault rectiﬁcation

7.1Maintenance .......................... 20

7.2Rectify faults .......................... 20

7.3Exchange the electronics ................. 21

7.4Instrument repair ....................... 22

8Dismounting

8.1Dismounting procedure .................. 23

8.2Disposal ............................. 23

9Supplement

9.1Technical data......................... 24

2OPTISWITCH 3000 C-with two-wire output

Contents

30061-EN-060830

9.2Dimensions ........................... 26

9.3Certiﬁcates ........................... 27

Supplementary operating instructions manuals

Information:

OPTISWITCH 3000 Cis available in diﬀerent versions.

Depending on the selected version,supplementary operating

instructions manuals may also come with the shipment.The

supplementary operating instructions manuals are listed in

section "Product description.

Operating instructions manuals for accessories and

replacement parts

Tip:

To ensure reliable setup and operation of your OPTISWITCH

3000 C,we oﬀer accessories and replacement parts.The

associated documents are:

lOperating instructions manual "Oscillator"

OPTISWITCH 3000 C-with two-wire output 3

Contents

30061-EN-060830

1About this document

1.1Function

This operating instructions manual has all the information you

need for quick setup and safe operation.Please read this

manual before you start setup.

1.2Target group

This operating instructions manual is directed to trained,

qualiﬁed personnel.The contents of this manual should be

made available to these personnel and put into practice by

them.

1.3Symbolism used

Information,tip,note

This symbol indicates helpful additional information.

Caution:If this warning is ignored,faults or

malfunctions can result.

Warning:If this warning is ignored,injury to persons and/or

serious damage to the instrument can result.

Danger:If this warning is ignored,serious injury to persons

and/or destruction of the instrument can result.

Ex applications

This symbol indicates special instructions for Ex applications.

lList

The dot set in front indicates a list with no implied sequence.

àAction

This arrow indicates a single action.

1Sequence

Numbers set in front indicate successive steps in a procedure.

4OPTISWITCH 3000 C-with two-wire output

About this document

30061-EN-060830

2For your safety

2.1Authorised personnel

All operations described in this operating instructions manual

must be carried out only by trained specialist personnel

authorised by the operator.For safety and warranty reasons,

any internal work on the instruments must be carried out only

by personnel authorised by the manufacturer.

2.2Appropriate use

OPTISWITCH 3000 Cis a sensor for level detection.

Detailed information on the application range of OPTISWITCH

3000 Cis available in chapter "Product description".

2.3Warning about misuse

Inappropriate or incorrect use of the instrument can give rise to

application-speciﬁc hazards,e.g.vessel overﬁll or damage to

system components through incorrect mounting or adjustment.

2.4General safety instructions

OPTISWITCH 3000 Cis a high-tech instrument requiring the

strict observance of standard regulations and guidelines.The

user must take note of the safety instructions in this operating

instructions manual,the country-speciﬁc installation standards

(e.g.the VDE regulations in Germany)as well as all prevailing

safety regulations and accident prevention rules.

2.5CE conformity

OPTISWITCH 3000 Cis in CE conformity with EMC (89/336/

EWG), fulﬁls NAMUR recommendation NE 21 and is in CE

conformity with LVD (73/23/EWG).

Conformity has been judged according to the following

standards:

lEMC:

-Emission EN 61326:1997 (class B)

-Susceptibility EN 61326:1997/A1:1998

lLVD:EN 61010-1:2001

OPTISWITCH 3000 C-with two-wire output 5

For your safety

30061-EN-060830

3Product description

3.1Conﬁguration

The scope of delivery encompasses:

lOPTISWITCH 3000 Clevel sensor

lDocumentation

-this operating instructions manual

-Supplementary instructions manual "Plug connector for

level sensors"(optional)

OPTISWITCH 3000 Cconsists of the following components:

lHousing cover

lHousing with electronics

lprocess ﬁtting with tuning fork

Fig.1:OPTISWITCH 3000 Cwith plastic housing

1Housing cover

2Housing with electronics

3Process ﬁtting

3.2Principle of operation

OPTISWITCH 3000 Cis a level sensor with tuning fork for level

detection.

It is designed for industrial use in all areas of process

technology and is preferably used for bulk solids.

Typical applications are overﬁll and dry run protection.Thanks

to its simple and robust measuring system,OPTISWITCH

3000 Cis virtually unaﬀected by the chemical and physical

properties of the bulk solid.

It functions even when exposed to strong external vibration or

changing products.

Scope of delivery

Components

Area of application

6OPTISWITCH 3000 C-with two-wire output

Product description

30061-EN-060830

Fault monitoring

The electronics of OPTISWITCH 3000 Ccontinuously mon-

itors the following criteria:

lCorrect vibrating frequency

lLine break to the piezo drive

If one of these faults is detected,the electronics signals this via

adeﬁned current to the signal conditioning instrument.The

connection cable to the vibrating element is also monitored.

The tuning fork is piezoelectrically energised and vibrates at its

mechanical resonance frequency of approx.150 Hz.When the

tuning fork is submerged in the product,the vibration

amplitude changes.This change is detected by the integrated

oscillator and converted into a switching command.

Depending on your requirements,OPTISWITCH 3000 Cwith

two-wire electronics can be connected to diﬀerent signal

conditioning instruments.Compatible signal conditioning in-

struments are listed under "Technical data".

The exact range of the power supply is stated in the "Technical

data"in the "Supplement".

3.3Operation

OPTISWITCH 3000 Ccan detect products with a density

>0.08 g/cm³(>0.003 lbs/in³).

On the electronics module you will ﬁnd the following indicating

and adjustment elements:

lsignal lamp for indication of the switching condition (green/

red)

lmode switch for selection of the output current

3.4Storage and transport

Your instrument was protected by packaging during transport.

Its capacity to handle normal loads during transport is assured

by a test according to DIN 55439.

The packaging of standard instruments consists of environ-

ment-friendly,recyclable cardboard.In addition,the sensor is

provided with a protective cover of cardboard.For special

versions PE foam or PE foil is also used.Dispose of the

packaging material via specialised recycling companies.

Physical principle

Power supply

Packaging

OPTISWITCH 3000 C-with two-wire output 7

Product description

30061-EN-060830

lStorage and transport temperature see "Supplement -

Technical data -Ambient conditions"

lRelative humidity 20 …85 %

Storage and transport tem-

perature

8OPTISWITCH 3000 C-with two-wire output

Product description

30061-EN-060830

4Mounting

4.1General instructions

In general,OPTISWITCH 3000 Ccan be mounted in any

position.The instrument must be mounted in such a way that

the vibrating element is at the height of the requested switching

point.

Use the recommended cables (see chapter "Connecting to

power supply")and tighten the cable gland.

You can give your OPTISWITCH 3000 Cadditional protection

against moisture penetration by leading the connection cable

downward in front of the cable entry.Rain and condensation

water can thus drain oﬀ.This applies mainly to mounting

outdoors,in areas where moisture is expected (e.g.by

cleaning processes)or on cooled or heated vessels.

Fig.2:Measures against moisture penetration

Do not hold OPTISWITCH 3000 Con the vibrating element.

The sensor can be damaged by the weight of the instrument.

Remove the protective cover just before mounting.

The process ﬁtting must be sealed if there is gauge or low

pressure in the vessel.Before use,check if the seal material is

resistant against the measured product and the process

temperature.

The max.permissible pressure is stated in the "Technical

data"in the "Supplement"or on the type label of the sensor.

The vibrating level switch is a measuring instrument and must

be treated accordingly.Bending the vibrating element will

destroy the instrument.

Switching point

Moisture

Transport

Pressure/Vacuum

Handling

OPTISWITCH 3000 C-with two-wire output 9

Mounting

30061-EN-060830

Warning:

The housing must not be used to screw in the instrument!

Applying tightening force on the housing can damage its

internal mechanical parts.

To screw in,use the hexagon above the thread.

4.2Mounting instructions

The vibrating element should protrude into the vessel to avoid

buildup.For that reason,avoid using mounting bosses for

ﬂanges and screwed ﬁttings.This applies particularly to use

with adhesive products.

Mount the instrument in such a way that the tuning fork does

not protrude directly into the ﬁlling stream.

20°

a. b.

Fig.3:Horizontal mounting

aConvex mounting

bConcave mounting

If such an installation location should be necessary,mount a

suitable protective sheet above or in front of the vibrating

element -see illustration a.).

In abrasive solids,mounting according to illustration b.has

proven.Aspout forms in the concave protective sheet

preventing wear of the protective sheet.

Socket

Filling opening

10 OPTISWITCH 3000 C-with two-wire output

Mounting

30061-EN-060830

Andere Handbücher für OPTISWITCH 3000 C

Inhaltsverzeichnis

Andere KROHNE Messgerät Handbücher

KROHNE

KROHNE WATERFLUX 3000 Bedienungsanleitung

KROHNE

KROHNE OPTISWITCH 5200C Bedienungsanleitung

KROHNE

KROHNE AF-E 400 Bedienungsanleitung

KROHNE

KROHNE H250 M10 Verdrahtungsschema

KROHNE

KROHNE VFC 200 Verdrahtungsschema

KROHNE

KROHNE DK32 Series Verdrahtungsschema

KROHNE

KROHNE OPTIWAVE 5200 C Verdrahtungsschema

KROHNE

KROHNE ALTOSONIC UFM 610 P Bedienungsanleitung

KROHNE

KROHNE WATERFLUX 3070 Bedienungsanleitung

KROHNE

KROHNE OPTISONIC 7300 Bedienungsanleitung

KROHNE

KROHNE M-PHASE 5000 Verdrahtungsschema

KROHNE

KROHNE OPTIMASS 1400 Bedienungsanleitung

KROHNE

KROHNE OPTIMASS 7400 Bedienungsanleitung

KROHNE

KROHNE OPTISONIC 6300 Bedienungsanleitung

KROHNE

KROHNE WATERFLUX 3070 Bedienungsanleitung

KROHNE

KROHNE OPTIMASS 3400 Bedienungsanleitung

KROHNE

KROHNE DWM 2000 D Bedienungsanleitung

KROHNE

KROHNE DK32 Series Verdrahtungsschema

KROHNE

KROHNE DK32 Series Verdrahtungsschema

KROHNE

KROHNE GA24 Verdrahtungsschema

KROHNE

KROHNE OPTISONIC 6300 Bedienungsanleitung

KROHNE

KROHNE DK37/M8 Verdrahtungsschema

KROHNE

KROHNE ifc 300 Verdrahtungsschema

KROHNE

KROHNE OPTISONIC 6300 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung