KTM 150 SX 2021 Handbuch

SETUP INSTRUCTIONS 2021

125 SX

150 SX

125 XC

Art. no. 3214364en

INTRODUCTION

*3214364en*

3214364en

02/2021

INTRODUCTION

Perform the work described in these setup instructions before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make

changes in the interest of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop

are not specified here. It is assumed that the work will be performed by a fully trained mechanic.

All specifications contained herein are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right

to modify or delete technical specifications, prices, colors, forms, materials, services, designs, equipment, etc.,

without prior notice and without specifying reasons, to adapt these to local conditions, as well as to stop produc-

tion of a particular model without prior notice. KTM accepts no liability for delivery options, deviations from fig-

ures and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that

does not belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission

of the copyright owner.

ISO 9001(12 100 6061)

KTM applies quality assurance processes that lead to the highest possible product quality as

defined in the ISO 9001 international quality management standard.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

Stallhofnerstraße 3

5230 Mattighofen, Austria

This document is valid for the following models:

125 SX (F6101U0)

150 SX (F6101U1)

125 XC US (F6175U3)

1 MEANS OF REPRESENTATION

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Indicates a voltage measurement.

Indicates a current measurement.

Indicates a resistance measurement.

Indicates the end of an activity including potential rework.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Indicates a proprietary name.

Name®Indicates a protected name.

Brand™ Indicates a brand available on the open market.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which

are explained in the glossary.

SETUP 2

2.1 Unpacking and setting up the vehicle

E00851-10

Package 2

–Remove the box and the plastic packaging.

Info

To avoid damaging the motorcycle during the setup,

leave the protective film on the vehicle until you

have finished.

–Remove the separate enclosure and unpack it. Check that

the scope of supply is complete using the enclosed pack-

ing list.

Info

The procedure in the event of missing parts is

described in the customer service manual.

–Have a lift stand available.

Lift stand (78129955100)

–Carefully loosen and remove the tension belt of the footrest

mount.

Info

An assistant prevents the motorcycle from falling

over.

402050-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

Info

The procedure in the event of transport damage is

described in the customer service manual.

E00850-10

Package 12

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling

over.

To avoid damaging the motorcycle during the setup,

leave the protective film on the vehicle until you

have finished.

–Remove the separate enclosure and unpack it. Check that

the scope of supply is complete using the enclosed pack-

ing list.

Info

The procedure in the event of missing parts is

described in the customer service manual.

2 SETUP

–Have a lift stand available.

Lift stand (78129955100)

–Together with an assistant, take the vehicle off the pallet.

402051-01

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

Info

The procedure in the event of transport damage is

described in the customer service manual.

A00001-11

–Remove the cardboard from around the shock absorber.

–Position the angle lever and linkage lever.

–Mount and tighten fitting 1.

Guideline

Nut, linkage lever

on angle lever

M14x1.5 60 Nm

(44.3 lbf ft)

–Mount and tighten screw 2.

Guideline

Screw, bottom

shock absorber

M10 60 Nm (44.3 lbf ft)

Loctite®2701™

Info

Raise the wheel slightly to be able to mount the

screw more easily.

–Route the clutch line with the clutch master cylinder

toward the front between the upper and lower triple

clamps.

–Install the fork legs. ( p. 10)

SETUP 2

K00620-10

–Remove screws 3. Take off the handlebar clamp. Remove

the handlebar and lay it to one side.

Info

Cover the components to protect them against damage.

Do not kink the cables and lines.

–Remove screws 4. Take off handlebar supports 5.

–Position rubber bushings 6and push through nuts 7from

below.

–Place handlebar supports in required position.

Info

The handlebar supports are longer and higher on one

side.

Position the left and right handlebar supports evenly.

–Mount and tighten screws 4.

Guideline

Screw, handle-

bar support

M10 40 Nm (29.5 lbf ft)

Loctite®243™

Warning

Danger of accidents A repaired handlebar poses a

safety risk.

If the handlebar is bent or straightened, the mate-

rial becomes fatigued. The handlebar may break as a

result.

–Change the handlebar if the handlebar is damaged

or bent.

–Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Position the handlebar clamp.

–Mount screws 3, but do not tighten yet.

–First bolt the handlebar clamp with screws 3onto the longer,

higher side of the handlebar supports so that both parts touch.

–Tighten screws 3evenly.

Guideline

Screw, handlebar

clamp

M8 20 Nm (14.8 lbf ft)

2 SETUP

F01707-01

–Position the controls on the right half of the handlebar.

F01706-01

–Position the controls on the left handlebar half.

–Mount the cable ties.

–Mount the fuel tank breather.

–Install the front wheel. ( p. 10)

–Install front fender. ( p. 11)

–Install the start number plate. ( p. 12)

F01708-01

–Mount the handlebar cushion.

R01229-10

–Position the new footrest and pin.

Info

Only insert the pin to the extent that the spring can still

be mounted.

SETUP 2

K00621-10

–Position spring as shown.

Spring Aengages in area B.

K00622-10

–Press the spring with special tool 8.

Footrest spring plier (79029083000)

The special tool is applied to area Con the footrest.

–Mount pin 9.

K00623-10

–Mount the washer and splint bk.

–Repeat these steps on the opposite side.

F01705-10

–Position the left frame protector.

–Insert the right frame protector from below and push it to the

rear.

–Mount and tighten screws bl with the washers.

Guideline

Screw, frame protec-

tor

M5 3 Nm (2.2 lbf ft)

–Mount and tighten screw bm.

Guideline

Screw, frame protec-

tor

M5 3 Nm (2.2 lbf ft)

–Mount the cable ties.

2 SETUP

–Unpack and mount the KTM PowerParts included in the deliv-

ery (optional).

Info

Read the accompanying KTM PowerParts fitting instruc-

tions.

–Attach the stickers included in the scope of supply (optional).

–Refuel. ( p. 13)

–Position all controls in their exact positions on the handlebar.

Tighten all screws.

–Remove the remaining films, the padding, the corrugated card-

board, and the other packaging material.

–Prepare the vehicle according to the specifications in

KTM Dealer.net for handover to the customer.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KTM Motorrad Handbücher

KTM

KTM 250 XC EU 2010 Handbuch

KTM

KTM 450 SMR Bedienungsanleitung

KTM

KTM 150 XC-W 2018 Bedienungsanleitung

KTM

KTM 1190 RC8 R 2014 Handbuch

KTM

KTM 125 EXC EU 2013 Handbuch

KTM

KTM 450 EXC RACING 2006 Bedienungsanleitung

KTM

KTM 1290 SUPER ADVENTURE S 2021 Handbuch

KTM

KTM 660 RALLY 2007 Betriebsanleitung

KTM

KTM 990 Adventure Baja Bedienungsanleitung

KTM

KTM Chassis 690 SMC Bedienungsanleitung

KTM

KTM 390 ADVENTURE 2022 Handbuch

KTM

KTM 125 Duke 2018 Bedienungsanleitung

KTM

KTM 250 EXC TPI EU 2021 Handbuch

KTM

KTM 250 EXC-F EU 2010 Bedienungsanleitung

KTM

KTM 1290 Super Duke R US 2020 Bedienungsanleitung

KTM

KTM 400 EXC EU 2010 Bedienungsanleitung

KTM

KTM 1290 Super Adventure Bedienungsanleitung

KTM

KTM 990 SUPER DUKE Handbuch

KTM

KTM 125 DUKE 2022 Bedienungsanleitung

KTM

KTM 60 SX 1999 Bedienungsanleitung

KTM

KTM 450 SXS-F Betriebsanleitung

KTM

KTM 2001 50 JR ADVENTURE Benutzerhandbuch

KTM

KTM 350 SX-F EU 2011 Handbuch

KTM

KTM 690 DUKE R EU Bedienungsanleitung

Beliebte Motorrad Handbücher anderer Marken

OHVALE

OHVALE GP-0 Stücklistenhandbuch

Yamaha

Yamaha Star XV19CTSZ 2009 Bedienungsanleitung

HYOSUNG

HYOSUNG ST7 Bedienungsanleitung

Husqvarna

Husqvarna FC 250 2016 Bedienungsanleitung

Ducati

Ducati SCRAMBLER 800 Gebrauchsanweisung

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Bedienungsanleitung

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung

Yamaha

Yamaha 2006 YZF-R1V Bedienungsanleitung

Fantic

Fantic Enduro 125 Bedienungsanleitung

Ducati

Ducati Supersport 750 desmodue Bedienungsanleitung

MV Agusta

MV Agusta 2008 F4 312RR 1078 Gebrauchsanweisung

Yamaha

Yamaha XVS650A Bedienungsanleitung

Yamaha

Yamaha YZF-R6T(C) Handbuch

Ducati

Ducati 748 monoposto strada Bedienungsanleitung

ATK

ATK 1988 250 Bedienungsanleitung

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Bedienungsanleitung

Triumph

Triumph Thunderbird Bedienungsanleitung

Yamaha

Yamaha 2006 FJR1300A Bedienungsanleitung