Kubota B2301 TLB ROPS Cab Bedienungsanleitung

Kubota B2301/2601 TLB ROPS Cab

*Cab is shown with optional equipment *

Kubota B2301/2601 ROPS Cab

This ROPS cab is designed and built to fit the Kubota B2301, B2601 with back-hoe installed.

Designed and Built by:

Tektite Manufacturing Inc:

427 Buffalo Street

P.O. Box 639

Winkler, MB

R6W 4A8

Canada

PH: 204-331-3463

Fax: 204-331-4159

[email protected]

www.tektite.ca

One year standard product warranty provided by Tektite.

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

Tektite Manufacturing Incorporated thanks you for purchasing a Kubota B2301/2601 ROPS cab!

Tektite has worked very hard to design and build this ROPS product and we hope that it

provides you with many years of ROPS protection.

Tektite’s ROPS products are designed to provide safe and dependable service during operation

when they are properly maintained according to the instructions. Please read this installation

manual carefully before installing and using this ROPS product.

The photos/illustrations provided in this manual may not provide all the detail needed, and are

for reference only.

All directions provided are from the reference point of the tractor seat facing the steering

wheel. All left and right references are from this view point.

For reference, please fill in the information below. This will assist your dealer in providing

service for this ROPS. It is advisable that this information be provided to your insurance

company as well in the event that the tractor is lost or damaged.

Vehicle Model: _________________________________________________________

ROPS Serial Number: ___________________________________________________

Date of Purchase: _______________________________________________________

Dealer Name: ___________________________________________________________

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

Parts List Standard Cab:

Description

Qty

Bolt, Flange, 5/8”x 1 ½”, Gr. 8, YD

Nut, Flange, 5/8”, Gr. 8, YD

Front Brackets

L&R

Bolt, Hex, 5/8” x 3”, Gr. 8, Yellow

Washer, Structural, ¼” Thick

180 O-rubber, 4 1/2" long (Diff Lock), 1/2" Pinch Notch

Under seat Shield (pre-upholstered)

Floormat, brake pedal

Push buttons, fasteners

Bolt, Hex, ½” x 4 ½”, Gr. 8

Wire Loop, 1/4”

Hex Bolt, M8 x 35

Parts List Optional Components:

Heater

Description

Qty

HS-6 hose clamps

Zip Ties, Standard

Heater Hose, 3/8" ID

12 FT

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

Installation Instructions:

1. Remove upper hoop of the two-post ROPS from machine. Take care during installation as

there will be a lot of pressure on the entire assembly.

2. Mark the wires going to both seat switches first, and then disconnect the wiring harness from

both switches.

3.Remove the seat from the seat track assembly tilt. Retain all fastening hardware.

4. Remove the seat track assembly completely from the tractor. Retain all fastening hardware.

5. Remove the toolbox as well as two bolts underneath toolbox. Retain all fastening hardware.

6. Un-bolt and remove the cup holder from the left fender. It will not be re-installed.

7. Un-bolt and remove both left and right fender grab handles.

8. Un-bolt and remove the left right plastic fender covers.

9. Remove the end plastic covers from the control levers. This will assist in installing the under-

seat shield in the following step.

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

10. Take the pre-upholstered under seat shield and roughly position it in the under seat area.

Slide the wiring harness through hole in shield. Slide the upholstery slots around and through

the levers in order to achieve a decent seal under the seat.

11. Fasten shield into place with factory hardware.

12. Re-install the end plastic caps to the control levers just removed.

13.Take the left front bracket and bolt to the outside of the loader mount plate shown with the

provided 5/8” x 1 ½” hex bolts and flange nuts. Loosely fasten only, see photo on next page.

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

14. Repeat for the right side front bracket.

15. Take the seat and put it back on top of the under seat shield. DO NOT fasten to tractor.

16.Return to the cab to install lift brackets next. To remove the gas shock on the left cab door,

slide a flat screwdriver underneath the small clip on the end cap that must be pulled UP order

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

to pop the shock off of the ball stud. The shock will release very easily when this is

accomplished. Lift the door assembly straight up and off of the cab and put aside for now.

17. Take the provided cab lift bolts, ½” x 4 ½” hex bolts and fasten to the mount nut located at

the top of the door behind the tab.

18. Use a lifting strap or chain, and connect the two lift bolts together. Prepare to lift the cab

up off of the shipping pallet with an over-head hoist or forklift.

19. Un-bolt the rear shipping bracket and the front shipping mount. Lift cab straight up.

Position the cab over the tractor and prepare to lower the cab down. The cab must come

straight down onto the tractor. Tighten or loosen the clamp as necessary that is keeping the

two post ROPS lower members together.

20. It is necessary to slide the rear shield of the cab onto the under-seat shield installed earlier

for proper sealing. The shield may need to bent back a little. The shield should seal at the very

back of the under seat shield.

21. Lower the cab straight down onto the front mount pad on the front bracket. Use the

provided 5/8” x 3” hex bolts, ¼” structural washer, and flange nut for the front isolator.

22. On the next photo, you can see which fastener is used for the rear mount location. Use the

provided 5/8” x 3”hex bolt, ¼” structural washer, and flange nut in the orientation as shown.

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

23.Ensure all fasteners have been started before any final torques are applied. For the 5/8”

fasteners, you can apply 205 ft-lbs of torque.

24.Un-hook the lift bolts and remove the lift straps or chain. Remove the lift bolts, store if cab

will be removed in the future.

25. Fasten the seat down onto the tractor with the provided M8 x 35 mm hex bolts.

26. Route the electrical harness from the bottom of the left A-post of the cab into the engine

bay. Connect the heavy red wire to the 12v power terminal on the starter. Use provided 1/4"

Front Bottom Hole

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

loop, shorten wire if necessary, then solder connector directly to red wire. Connect the heavy

black wire to the ground bolt on the starter. Use the provided 1/4" loop, shorten wire if

necessary, then solder connector directly to the black wire.

27. Take the pedals floormat provided and slide through the pedals on the left side. Use the

provided push button fasteners. It will be necessary to drill ¼” holes through the floormat and

floor sheet-metal.

28.To ensure a better seal of the cab to the tractor, it is recommended that a black silicone be

used between all weather stripping and tractor contact points.

If cab is equipped with a heater, proceed with the following steps.

RH 2320 floormat shown

June 2021© Kubota B2301/2601 ROPS Cab Installation Manual

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kubota Traktor Handbücher

Kubota

Kubota L4701 Bedienungsanleitung

Kubota

Kubota WSM M8540 Gebrauchsanweisung

Kubota

Kubota M5N-091 Bedienungsanleitung

Kubota

Kubota ME5700 Gebrauchsanweisung

Kubota

Kubota MX4800 Bedienungsanleitung

Kubota

Kubota RT120Q Bedienungsanleitung

Kubota

Kubota B2650 Bedienungsanleitung

Kubota

Kubota LA535 Bedienungsanleitung

Kubota

Kubota L3130 Gebrauchsanweisung

Kubota

Kubota WSM B2050 Gebrauchsanweisung

Kubota

Kubota M6040 Bedienungsanleitung

Kubota

Kubota BX1870 Gebrauchsanweisung

Kubota

Kubota L3560 Bedienungsanleitung

Kubota

Kubota B3150 Bedienungsanleitung

Kubota

Kubota L2501 Bedienungsanleitung

Kubota

Kubota WSM F2880 Bedienungsanleitung

Kubota

Kubota M6060 Bedienungsanleitung

Kubota

Kubota L5060 Bedienungsanleitung

Kubota

Kubota M7-132 Bedienungsanleitung

Kubota

Kubota B2620 Bedienungsanleitung

Kubota

Kubota STV32 Bedienungsanleitung

Kubota

Kubota BX1860 Gebrauchsanweisung

Kubota

Kubota WSM BX1870 Gebrauchsanweisung

Kubota

Kubota M7-132 Bedienungsanleitung

Beliebte Traktor Handbücher anderer Marken

Ariens

Ariens 936051 Bedienungsanleitung

MacDon

MacDon M150 Bedienungsanleitung

Belarus

Belarus 3522.5 Bedienungsanleitung

CARRARO

CARRARO Vigneto Bedienungsanleitung

Cub Cadet

Cub Cadet 3208 Bedienungsanleitung

GREMO

GREMO 1250F Gebrauchsanweisung

HATTAT

HATTAT A90 Bedienungsanleitung

AL-KO

AL-KO Heritage RS 14/82 Bedienungsanleitung

Webb

Webb WE1742SD Bedienungsanleitung

MacDon

MacDon 9250 Bedienungsanleitung

Toro

Toro 03200 Reelmaster 3100-D Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON 5400 Series Bedienungsanleitung

Iseki

Iseki TXG23 Bedienungsanleitung

Toro

Toro 25429 Bedienungsanleitung

New Holland

New Holland T4.80V Bedienungsanleitung

Gravely

Gravely D Bedienungsanleitung

Case

Case JX 90 Bedienungsanleitung

Challenger

Challenger MT265B Bedienungsanleitung