KVH Industries TracVision M3-ST Bedienungsanleitung

TracVision M3 Installation Guide

TracVision M3 – ST Version

DIRECTV®Mobile Receiver

TracVision M3/M2

Addendum

PLEASE READ!

Important Addendum to Your Product Manual

This addendum applies to the TracVision®M3 and M2.

Rubber Sealing Boot to Protect the Antenna’s Cable Connection

A rubber boot is provided with the antenna cable to help protect the

cable connection from the elements. An extension is supplied in the

kitpack in case you need to use a right-angle connector. Follow the

guidelines below to use these sealing components.

• When routing the cable belowdecks, be sure to keep the end with

the rubber boot at the antenna site so that you can install the boot

at the antenna’s cable connection.

• If you are using a right-angle connector, place the right-angle

rubber boot extension onto the end of the cable before you connect

it. Then, after you connect the cable, slide the extension up the

cable until it covers the right-angle connector.

• Once you have connected the cable to the antenna, slide the rubber

boot up the cable until it covers the connector. If you are using a

right-angle connector, be sure the boot mates with the extension, as

shown below.

Right-Angle

Connector Extension Rubber Boot

Connector

Cover

Rubber Boot

Right-Angle

Boot Extension

ECO #8305

These instructions explain how to install the TracVision M3 satellite TV antenna

system on a vessel. Complete instructions on how to use the system are provided in

the Quick Start Guide and Receiver User’s Guide.

TracVision®M3 Installation Guide

Who Should Install the System?

To ensure a safe and effective installation, KVH recommends that a KVH-authorized

marine technician install the TracVision M3 system. To find a technician near you, go to

www.kvh.com/wheretogetservice. If you purchased the product and decide to install it

yourself, please see the enclosed warranty statement for warranty implications.

Technical Support

If you need technical assistance, please contact KVH

Technical Support:

Phone: 1-401-847-3327

E-mail: [email protected]

KVH and TracVision are registered trademarks of KVH Industries, Inc.; DIRECTV is a registered trademark of DIRECTV, Inc.

The unique light-colored dome with dark contrasting base is a registered trademark of KVH Industries, Inc. U.S. patents pending.

The information in this document is subject to change without notice. No company shall be liable for errors contained herein.

Important Safety Precaution

DO NOT apply power to the TracVision antenna with the radome removed

because the antenna has moving parts that can cause injury.

CAUTION

Installation Steps

1. Inspect parts and get tools 7. Wire the receiver

2. Plan the installation 8. Connect power

3. Prepare the mounting site 9. Install the receiver

4. Wire the antenna 10. Install batteries in the remote

5. Remove the restraint 11. Test the system

6. Mount the antenna 12. Educate the customer

ST Version with DIRECTV

Mobile Receiver

1. Unpack the box and ensure it contains

everything shown on the Contents List.

Save the packaging in case you need to reship

the system.

2. Carefully examine all of the supplied

parts to ensure nothing was damaged in

shipment.

3. Gather all of the tools and materials listed

below. You will need these items to

complete the installation.

4. Peel off the extra serial number label

(taped to the antenna) and affix it in the

appropriate box on the red Activation

Card.

Inspect Parts and Get Tools

Always lift the antenna by the

silver base and never by the

radome or any portion of the

internal antenna assembly.

• #2 Phillips-head

screwdriver

•7⁄16" open-end wrench

•7⁄16" socket wrench

•1⁄2" socket or open-end

wrench

• Electric drill

•5⁄16" (8 mm) drill bit

• Silicone sealant or

equivalent

• Hole saw of desired diameter

(for cable access hole, see page 4)

• Adhesive tape

• Light hammer

• Center punch

• Eight (8) 1⁄4" fasteners

(optional for mounting the receiver,

see page 10)

Affix Serial

Number

Antenna

Receiver Connector

Cover

Radome

Base

051099999

Before you begin, consider the following installation guidelines:

Plan the Installation

Antenn

Vessel Platform

Radar

Blocked!

4 x 0.31"

( 0.79 cm)

15.5"

(39.37 cm)

9.2"

(23.37 cm)

4.6"

(11.68 cm)

2.8"

(7.11 cm) 5.6"

(14.22 cm)

FWD

17.32"

(44 cm)

• Minimize blockage. The antenna requires a

clear view of the sky to receive satellite TV.

The fewer obstructions above decks, the

better the system will perform.

• When choosing a mounting surface, ensure

it is wide enough to accommodate the

antenna’s base. See illustrations for antenna

dimensions.

• Ensure the mounting surface is flat, level

(within ±2º), and strong enough to support

the 18-pound antenna. Use a separate

mounting plate, if necessary.

• Custom mounting solutions, including

struts and masts, are available from several

third-party manufacturers. Contact your

local KVH dealer for details.

• KVH recommends that you do not mount

the antenna on the same level as the radar,

because the radar’s energy might overload

the antenna.

• Be sure to mount the antenna near enough

to the supplied belowdecks receiver to

allow you to connect the 50-ft. (15 m) coax

cable between the antenna and the receiver,

while still maintaining sufficient slack in

the cable. The antenna cable CANNOT be

extended.

• When choosing a location for the receiver,

find a dry, well-ventilated area belowdecks

away from any heat sources or salt spray.

Also be sure the receiver’s front panel will

be easily accessible to the user.

1. Unfold the supplied template and

place it onto the mounting surface.

Make sure the “FWD” (forward)

arrow points toward the bow and

is parallel to the vessel’s centerline.

You do not need to mount the antenna

exactly on the vessel’s centerline, but

the antenna’s forward arrow must be

parallel to it.

2. Use the template to mark the four

hole locations on the mounting

surface.

3. Drill a 5⁄16" (8 mm) hole at the four

locations you marked in Step 2.

Later, you will insert four 1⁄4"-20 bolts

from above to secure the antenna to

the mounting surface.

4. Mark a location for the cable access

hole, either in the center of the

antenna mounting hole pattern or in

an area aft of the antenna. Later, you

will route the antenna cable through

this hole and into the vessel.

5. Drill the cable access hole in the

location you marked in Step 4. Be

sure to size the hole appropriately

to maintain a cable bend radius of

at least 3" (75 mm). If the hole location

is in the center of the antenna

mounting hole pattern, the diameter of

the cable access hole must not exceed

3.5" (88 mm). Smooth the edges of

the hole to protect the cable.

Prepare the Mounting Site

15.5"

(39.4 cm)

2.8"

(7.1 cm)

5.6"

(14.2 cm)

4.6"

(11.7 cm)

9.2"

(23.4 cm)

4 x 0.31"

( 0.8 cm)

Mounting Holes

Cable Access Hole

(Suggested Location

)

Antenna Base

Be sure the mounting surface is

flat and level. Use a separate

mounting plate, if necessary.

Drilling Antenna

Mounting Holes

1. Clean and dry the antenna mounting

surface.

2. Peel off the paper backing from the donut-

shaped foam seal to expose the adhesive.

Then press the foam seal down firmly onto

the mounting surface, centered between the

antenna mounting holes.

3. Using the supplied 3 mm Allen hex key,

remove the connector cover from the

antenna’s base. Save the cover and the four

M4 cap screws for later use.

4. Route either end of the antenna cable into

the vessel. Later, you will connect this end of

the cable to the belowdecks receiver. You will

connect the other end to the antenna.

5. If you wish to route the cable beneath the

antenna, attach the right-angle connector to

the end of the cable. Hand-tighten, then

tighten with a 7⁄16" wrench for 1⁄4turn to

ensure an electrical and weather-proof

connection.

6. Connect the cable to the antenna. Hand-

tighten, then tighten with a 7⁄16" wrench for

1⁄4turn. Rigging tape is recommended to protect

the connection.

7. Reattach the cover over the connector.

Secure in place with the M4 cap screws you

removed in Step 3. The cover must be

attached before you mount the antenna.

8. Leave an adequate service loop,

approximately 8" (20 cm) of slack, in the

antenna cable for easy serviceability.

9. Weatherproof and seal the cable access hole

as needed.

Wire the Antenna

Foam Seal

Antenna Cable

Connector Cover

Right-angle

Connector

Wire the Antenna

1. Remove the three #10-32 screws securing the

radome to the antenna. Carefully remove the

radome and set it aside in a safe place. Due

to the snug fit, some contact between the

radome’s sealing gasket and the antenna

mechanism is normal.

2. Using a 7⁄16" socket wrench, remove the

shipping restraint bolt, washer, and spacer

securing the antenna assembly to the base.

Save the restraint for future use.

3. Position the antenna onto the mounting

surface. The antenna’s base should rest

squarely atop the foam seal.

4. Align the four holes in the antenna’s base

with the four holes in the mounting surface.

Be sure that the antenna’s

“Forward” arrow points

toward the bow and is

parallel to the vessel’s

centerline.

Remove the Restraint

Antenna

Radome

Washer

Bolt

Spacer

Be sure to remove the shipping

restraint bolt, washer, and spacer.

The antenna will not work with this

hardware still installed.

“Forward” Arrow

Shipping Restraint

1. Secure the antenna’s base to the mounting

surface using four 1⁄4"-20 bolts, 5⁄8" washers,

1" washers, and lock nuts, as shown in the

illustration. Be sure to insert the bolts from

above and use the supplied hardware for a

secure installation.

2. Tighten the bolts until the foam seal is fully

compressed and the antenna’s four rubber

feet are bottomed against the mounting

surface.

3. Reinstall the antenna radome. The radome’s

“TracVision” labels should face fore and aft.

While pressing the radome down onto the

base, secure the radome to the base using

the three #10-32 screws you removed

earlier.

4. Install a protective plastic screw cap

(supplied in the kit) over each radome screw.

Mount the Antenna

1/4"-20 x 3" Bolt

1/4" Flat Washer

(5/8" diameter)

Antenna Base

Foam Seal

Mounting Surface

1/4" Flat Washer

(1" diameter)

1/4"-20 Lock Nut

Insert the mounting bolts into

the antenna’s base from above,

not below.

Tighten Bolts

from Above

Antenna Mounted

1. Connect the antenna cable (A) to the “To KVH

Antenna” jack. Do not kink/stress the cable.

2. Connect the RF converter cable (B) to the “RF

Remote Input” jack.

3. Connect the receiver to the TV’s video input.

Choose one of the following options:

Option 1 - RCA-type A/V jack (cable included)

Option 2 - S-Video jack

If the TV has only a coaxial input, you will need an

RF modulator (Radio Shack model 15-2526 or

equivalent).

4. Connect the receiver to the TV’s audio input.

Choose one of the following options:

Option 1 - RCA-type A/V jacks (cables included)

Option 2 - Digital audio jack

5. Tighten all connections and leave enough slack in

the cables (service loop) for easy serviceability,

allowing you to access the receiver’s rear panel.

For details on connecting any additional receivers,

please see Appendix A in the Receiver User’s Guide.

Wire the Receiver

Do not shorten or extend

the antenna cable. Since the

antenna cable carries data,

power, and communications,

the integrity of this cable

and its connections is very

important.

Antenna

Deck

Be sure to route cables with-

in the vessel appropriately to

avoid damage. For example,

do not route any cables

through wet areas (bilges) or

near hot exhaust pipes.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KVH Industries Satellitenfernsehsystem Handbücher

KVH Industries

KVH Industries TracVision R5SL Bedienungsanleitung

KVH Industries

KVH Industries TracVision R1ST Bedienungsanleitung

KVH Industries

KVH Industries TracVision 4 Bedienungsanleitung

KVH Industries

KVH Industries TracVision TV1 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries KVH TracVision Installationsanleitung

KVH Industries

KVH Industries TracVision M7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision RV1 Bedienungsanleitung

KVH Industries

KVH Industries TracVision C3 Bedienungsanleitung

KVH Industries

KVH Industries TracVision 6 Bedienungsanleitung

KVH Industries

KVH Industries TracVision 4 Bedienungsanleitung

KVH Industries

KVH Industries LF Bedienungsanleitung

KVH Industries

KVH Industries TracVision HD7 Bedienungsanleitung

KVH Industries

KVH Industries TracNet H60 Bedienungsanleitung

KVH Industries

KVH Industries KVH TracVision TracVision G6 Bedienungsanleitung

KVH Industries

KVH Industries TracVision 4 Bedienungsanleitung

KVH Industries

KVH Industries TracVision R4 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M9 Leitfaden

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision R5SL Leitfaden

KVH Industries

KVH Industries TracVision M7 Bedienungsanleitung

Beliebte Satellitenfernsehsystem Handbücher anderer Marken

Dish TV

Dish TV DVB-S6800PLUS Bedienungsanleitung

Avermedia

Avermedia AVer3D R889 Bedienungsanleitung

Kathrein

Kathrein MobiSet 2 Digital CAP 600 Bedienungsanleitung

Philips

Philips DSX 5250 Bedienungsanleitung

Winegard

Winegard RMFLDM4 Bedienungsanleitung

DefineSat

DefineSat VM55 Bedienungsanleitung

Dish Network

Dish Network 112182 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane sailor 60 Technisches Handbuch

JRC

JRC NJT8304 Series Bedienungsanleitung

Bell

Bell EXPRESSVU Bedienungsanleitung

Promax

Promax SATHUNTER Bedienungsanleitung

SatKing

SatKing PRO MAX Bedienungsanleitung

Dish Network

Dish Network Satellite Television Bedienungsanleitung

Uniden

Uniden SQ530 Bedienungsanleitung

VuQube

VuQube V20 Bedienungsanleitung

VIARK

VIARK SAT 4K Bedienungsanleitung

KING

KING Tailgater VQ4500 Bedienungsanleitung

Apollo Entertainment

Apollo Entertainment KiwiSat Leitfaden