KVH Industries TracVision M3 Bedienungsanleitung

TracVision M3 Installation Guide

These instructions explain how to install the TracVision M3 satellite TV antenna

system on a vessel. Complete instructions on how to use the system are provided in

the Quick Start Guide and Receiver User’s Guide.

TracVision®M3 Installation Guide

Who Should Install the System?

To ensure a safe and effective installation, KVH recommends that a KVH-authorized

marine technician install the TracVision M3 system. To find a technician near you, go to

www.kvh.com/wheretogetservice. If you purchased the product and decide to install it

yourself, please see the enclosed warranty statement for warranty implications.

Technical Support

If you need technical assistance, please contact KVH Technical Support:

Phone: 1-401-847-3327

E-mail: [email protected]

Internet: www.kvh.com/help

Receiver Activation

Once the system is fully installed, the owner needs to call

KVH’s Activation Department to activate the receiver for

DIRECTV®service:

Toll-free at 1-866-551-8004

The owner will need the red Activation Card when

calling to activate. In addition, the antenna will need to

be turned on and locked onto the satellite. See page v of

the Receiver User’s Guide for details.

KVH and TracVision are registered trademarks of KVH Industries, Inc.; DIRECTV is a registered trademark of DIRECTV, Inc.

The information in this document is subject to change without notice. No company shall be liable for errors contained herein.

051099999 051077777

Important Safety Precaution

DO NOT apply power to the TracVision antenna with the radome removed

because the antenna has moving parts that can cause injury.

CAUTION

1. Unpack the box and ensure it contains

everything shown on the Contents List. Save

the packaging in case you need to reship the

system.

2. Carefully examine all of the supplied parts to

ensure nothing was damaged in shipment.

3. Gather all of the tools and materials listed

below. You will need these items to complete

the installation.

4. Peel off the extra serial number label (taped to

the antenna) and affix it in the appropriate

box on the red Activation Card.

Inspect Parts and Get Tools

Always lift the antenna by the

silver base and never by the

radome or any portion of the

internal antenna assembly.

• #2 Phillips screwdriver

•7⁄16" open-end wrench

•7⁄16" socket wrench

•1⁄2" socket or open-end

wrench

• Electric drill

•5⁄16" (8 mm) drill bit

• Silicone sealant or

equivalent

• Hole saw of desired diameter

(for cable access hole, see page 4)

• Adhesive tape

• Light hammer

• Center punch

• Four 1⁄4" fasteners

(optional for mounting the receiver,

see page 10)

Affix Serial

Number

Antenna

Receiver Connector

Cover

Radome

Base

051099999

Before you begin, consider the following installation guidelines:

Plan the Installation

Antenna

Vessel Platform

Radar

Blocked!

4 x 0.31"

( 0.79 cm)

15.5"

(39.37 cm)

9.2"

(23.37 cm)

4.6"

(11.68 cm)

2.8"

(7.11 cm) 5.6"

(14.22 cm)

FWD

17.32"

(44 cm)

• Minimize blockage. The antenna requires a

clear view of the sky to receive satellite TV.

The fewer obstructions above decks, the

better the system will perform.

• When choosing a mounting surface, ensure

it is wide enough to accommodate the

antenna’s base. See illustrations for antenna

dimensions.

• Ensure the mounting surface is flat, level

(within ±2º), and strong enough to support

the 18-pound antenna. Use a separate

mounting plate, if necessary.

• Custom mounting solutions, including

struts and masts, are available from several

third-party manufacturers. Contact your

local KVH dealer for details.

• KVH recommends that you do not mount

the antenna on the same level as the radar,

because the radar’s energy might overload

the antenna.

• Be sure to mount the antenna near enough

to the supplied belowdecks receiver to

allow you to connect the 50-ft. (15 m) coax

cable between the antenna and the receiver,

while still maintaining sufficient slack in

the cable. The antenna cable CANNOT be

extended.

• When choosing a location for the receiver,

find a dry, well-ventilated area belowdecks

away from any heat sources. Also be sure

the receiver’s front panel will be easily

accessible to the user and the three lights on

the top of the receiver will be visible.

1. Unfold the supplied template

and place it onto the mounting

surface. Make sure the “FWD”

(forward) arrow points toward

the bow and is parallel to the

vessel’s centerline. You do not

need to mount the antenna exactly

on the vessel’s centerline, but the

antenna’s forward arrow must be

parallel to it.

2. Use the template to mark the

four hole locations on the

mounting surface.

3. Drill a 5⁄16" (8 mm) hole at the

four locations you marked in

Step 2. Later, you will insert four

1⁄4"-20 bolts from above to secure the

antenna to the mounting surface.

4. Mark a location for the cable access

hole, either in the center of the

antenna mounting hole pattern or in

an area aft of the antenna. Later, you

will route the antenna cable through

this hole and into the vessel.

5. Drill the cable access hole in the

location you marked in Step 4. Be

sure to size the hole appropriately

to maintain a cable bend radius of

at least 3" (75 mm). If the hole location

is in the center of the antenna

mounting hole pattern, the diameter of

the cable access hole must not exceed

3.5" (88 mm). Smooth the edges of

the hole to protect the cable.

Prepare the Mounting Site

15.5"

(39.4 cm)

2.8"

(7.1 cm)

5.6"

(14.2 cm)

4.6"

(11.7 cm)

9.2"

(23.4 cm)

4 x 0.31"

( 0.8 cm)

Mounting Holes

Cable Access Hole

(Suggested Location

)

Antenna Base

Be sure the mounting surface is

flat and level. Use a separate

mounting plate, if necessary.

Drilling Antenna

Mounting Holes

1. Clean and dry the antenna mounting

surface.

2. Peel off the paper backing from the donut-

shaped foam seal to expose the adhesive.

Then press the foam seal down firmly onto

the mounting surface, centered between the

antenna mounting holes.

3. Using the supplied 3 mm Allen hex key,

remove the connector cover from the

antenna’s base. Save the cover and the four

M4 cap screws for later use.

4. Route either end of the antenna cable into

the vessel. Later, you will connect this end of

the cable to the belowdecks receiver. You will

connect the other end to the antenna.

5. If you wish to route the cable beneath the

antenna, attach the right-angle connector to

the end of the cable. Hand-tighten, then

tighten with a 7⁄16" wrench for 1⁄4turn to

ensure an electrical and weather-proof

connection

6. Connect the cable to the antenna. Hand-

tighten, then tighten with a 7⁄16" wrench for

1⁄4turn. Rigging tape is recommended to protect

the connector.

7. Reattach the cover over the connector.

Secure in place with the M4 cap screws you

removed in Step 3. The cover must be

attached before you mount the antenna.

8. Leave an adequate service loop,

approximately 8" (20 cm) of slack, in the

antenna cable for easy serviceability.

9. Seal the cable access hole with silicone

sealant or equivalent.

Wire the Antenna

Foam Seal

Antenna Cable

Connector Cover

Right-angle

Connector

Wire the Antenna

1. Remove the three #10-32 screws securing

the radome to the antenna. Carefully

remove the radome and set it aside in a safe

place. Due to the snug fit, some contact

between the radome’s sealing gasket and the

antenna mechanism is normal.

2. Position the antenna onto the mounting

surface. The antenna’s base should rest

squarely atop the foam seal.

3. Align the four holes in the antenna’s base

with the four holes in the mounting surface.

Be sure the antenna’s “Forward” arrow

points toward the bow.

4. Secure the antenna’s base to the mounting

surface using four 1⁄4"-20 bolts, 5⁄8" washers,

1" washers, and lock nuts, as shown in the

illustration. Be sure to insert the bolts from

above and use the supplied hardware for a

secure installation.

5. Tighten the bolts until the foam seal is fully

compressed and the antenna’s four rubber

feet are bottomed against the mounting

surface.

Mount the Antenna

1/4"-20 x 3" Bolt

1/4" Flat Washer

(5/8" diameter)

Antenna Base

Foam Seal

Mounting Surface

1/4" Flat Washer

(1" diameter)

1/4"-20 Lock Nut

“Forward” Arrow

Insert the mounting bolts into

the antenna’s base from above,

not below.

Tighten Bolts

from Above

1. Using a 7⁄16" socket wrench, remove the two

bolts securing the antenna assembly to the

base. Be sure to remove both of these

shipping restraints, along with the washers

and spacers. Save the restraints for future use.

Remove the Restraints

Shipping Restraints

Washer

Bolt

Spacer

Antenna

Radome

2. Reinstall the antenna radome. While

pressing the radome down onto the base,

secure the radome to the base using the three

#10-32 screws you removed earlier. The

radome’s “TracVision” labels should face fore

and aft.

3. Install a protective plastic screw cap (supplied

in the kit) over each radome screw.

Antenna Mounted

Be sure to remove both shipping

restraint bolts, washers, and

spacers. The antenna will not

work with these restraints still

installed.

1. Connect the antenna cable (A) to the “To KVH

Antenna” jack. Do not kink/stress the cable.

2. Connect the RF converter cable (B) to the “RF

Remote Input” jack.

3. Connect the receiver to the vessel’s entertainment

system (TV). Choose one of the following options:

Option 1 - RCA-type A/V jacks (use bottom row)

Option 2 - S-Video jack (provides best picture quality)

Option 3 - RF coaxial connector

Cables for option 1 are included in the kit.

4. (Optional) If you have a VHF TV antenna onboard,

you can connect it to the “VHF Antenna In” jack on

the receiver. If you connect a VHF antenna to the

receiver, you need to use the receiver’s RF coaxial

connector (option 3) to supply VHF video to the TV.

5. Be sure to tighten all connections. Also be sure to

leave enough slack in the cables (service loop) for

easy serviceability, allowing you to access the

receiver’s rear panel with the cables connected.

For details on connecting an additional receiver,

please see Appendix A in the Receiver User’s Guide.

Wire the Receiver

Do not shorten or extend

the antenna cable. Since the

antenna cable carries data,

power, and communications,

the integrity of this cable

and its connections is very

important.

Antenna

RF Converter

Receiver

Deck

Service/

Maintenance

Only

To Audio

To Video

(Option 1)

To Video

(Option 1)

To Video

(Option 3)

To Video

(Option 2)

To VHF Antenna

(Optional)

POWER

VEHICLE POWER

(10-16 VDC)

VHF ANTENNA

AUDIO R AUDIO L VIDEO S – VIDEO PHONE JACK

REMOTE

INPUT OUT TO TV

TUNER

SATELLITE IN

CAUTION

This device complies with Part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) This device must not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Tested to comply

with FCC Standards

TO SATELLITE

TO KVH

ANTENNA

DIAGNOSTICS

PORT 1

DIAGNOSTICS

PORT 2

(A)

(B)

Do not disconnect the

short cable on the back

of the receiver.

Be sure to route cables with-

in the vessel appropriately to

avoid damage. For example,

do not route any cables

through wet areas (bilges) or

near hot exhaust pipes.

Connect Power

The receiver requires a 10-16 volts DC (VDC) power

input supporting 50 watts (4.2 amps @ 12 VDC).

1. Before you connect the receiver’s power wires,

turn off vessel power and test the circuit to

ensure no power is present.

2. Connect the receiver’s individual power wires to

a dedicated 10-amp or 15-amp circuit breaker.

Connect the negative (black) wire to ground

(power return), and connect the positive (red)

wire to +12 VDC vessel power.

3. Plug the other end of the power wires into the

“Vehicle Power” jack on the receiver’s rear panel.

Do not remove the small ferrite coil that is clamped

onto the power wires. This coil suppresses EMI

(electromagnetic interference) from the receiver.

For your own safety, shut

down vessel power before

you connect the wires.

Receiver

DC Power

Ground

Vessel Power

(10-16 VDC)

Fuse (6 amp)

POWER

VEHICLE POWER

(10-16 VDC)

VHF ANTENNA

AUDIO R AUDIO L VIDEO S – VIDEO PHONE JACK

REMOTE

INPUT OUT TO TV

TUNER

SATELLITE IN

CAUTION

This device complies with Part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) This device must not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Tested to comply

with FCC Standards

TO SATELLITE

TO KVH

ANTENNA

DIAGNOSTICS

PORT 1

DIAGNOSTICS

PORT 2

Ferrite

Coil

Andere Handbücher für TracVision M3

Inhaltsverzeichnis

Andere KVH Industries Satellitenfernsehsystem Handbücher

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M9 Leitfaden

KVH Industries

KVH Industries TracVision TV10 Bedienungsanleitung

KVH Industries

KVH Industries KVH TracVision TracVision G6 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M7 Bedienungsanleitung

KVH Industries

KVH Industries antenna system Bedienungsanleitung

KVH Industries

KVH Industries KVHTRACVISION G4 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision 4 Bedienungsanleitung

KVH Industries

KVH Industries TracNet H60 Bedienungsanleitung

KVH Industries

KVH Industries LF Bedienungsanleitung

KVH Industries

KVH Industries TracVision M7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision RV1 Bedienungsanleitung

KVH Industries

KVH Industries KVH TracVision Installationsanleitung

KVH Industries

KVH Industries TracVision R4 Bedienungsanleitung

KVH Industries

KVH Industries KVH TracVision TracVision G6 Bedienungsanleitung

KVH Industries

KVH Industries TracVision HD7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M3 Bedienungsanleitung

KVH Industries

KVH Industries TracVision R5SL Bedienungsanleitung

KVH Industries

KVH Industries TracVision HD7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision HD11 Bedienungsanleitung

KVH Industries

KVH Industries TracVision 6 Bedienungsanleitung

KVH Industries

KVH Industries TracVision C3 Bedienungsanleitung

Beliebte Satellitenfernsehsystem Handbücher anderer Marken

Dish TV

Dish TV DVB-S6800PLUS Bedienungsanleitung

Avermedia

Avermedia AVer3D R889 Bedienungsanleitung

Kathrein

Kathrein MobiSet 2 Digital CAP 600 Bedienungsanleitung

Philips

Philips DSX 5250 Bedienungsanleitung

Winegard

Winegard RMFLDM4 Bedienungsanleitung

DefineSat

DefineSat VM55 Bedienungsanleitung

Dish Network

Dish Network 112182 Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane sailor 60 Technisches Handbuch

JRC

JRC NJT8304 Series Bedienungsanleitung

Bell

Bell EXPRESSVU Bedienungsanleitung

Promax

Promax SATHUNTER Bedienungsanleitung

SatKing

SatKing PRO MAX Bedienungsanleitung

Dish Network

Dish Network Satellite Television Bedienungsanleitung

Uniden

Uniden SQ530 Bedienungsanleitung

VuQube

VuQube V20 Bedienungsanleitung

VIARK

VIARK SAT 4K Bedienungsanleitung

KING

KING Tailgater VQ4500 Bedienungsanleitung

Apollo Entertainment

Apollo Entertainment KiwiSat Leitfaden