La Crosse Technology WT-3126B Handbuch

Radio Controlled Analog Clock

Quick set up instructions

Welcome to the world of radio controlled timekeeping technology. We hope you will enjoy the

convenience of never having to set your clock again and the confidence of knowing exactly what time it

is.

• Insert 1 fresh AA, LR6 1.5 volt ALKALINE battery

• Press button to select a time zone. THAT’S IT! During the night your clock will

automatically set itself.

For a better understanding of how and why your clock works please continue reading.

Nothing is more precisely measured than time!

And nothing keeps track of time more precisely and trouble free than La Crosse Technology radio controlled

clocks.

Since the beginning of time, man has been fascinated with the measurement of time and has devised more

accurate machines to trap and measure time. Today, time is precisely measured in the United States by the most

accurate clock in North America, the Atomic Clock of the US National Institute of Standards and Technology,

Time and Frequency Division in Boulder, Colorado. A team of atomic physicists continually measures every

second of every day to an accuracy of ten billionths of a second per day. These physicists have created an

international standard, measuring a second as 9,192,631,770 vibrations of a Cesium 133 atom in a vacuum. This

atomic clock regulates the WWVB radio transmitter located in Fort Collins, Colorado, where the exact time signal

is continuously broadcast throughout the United States at 60 kHz to take advantage of stable long wave radio

paths found in that frequency range. Radio waves at these low frequencies use the earth and the ionosphere as a

wave-guide and follow the curvature of the earth for long distances.

The built in antenna system will receive the WWVB signal anywhere in North America within 2000 miles of

Fort Collins where long-wave radio reception is undisturbed. A microprocessor activates the receiver and

processes the time signal from Fort Collins overnight.

Through the radio signals, La Crosse Technology radio controlled clocks always keep precise time. The

changeover from standard time to daylight savings time, and vice versa, takes place automatically with the same

precision.

Additional details

To set up your clock simply install one fresh AA, LR6 ALKALINE battery. Due to the nature of long wave radio

signals it is normally not possible to receive a signal during the day so it is best to install the battery late in the

evening. Select your time zone by pressing one of the four time zone buttons PT-Pacific Time, MT-Mountain

Time, CT-Central Time, ET-Eastern Time. The time zone buttons may be pressed any time after installing the

batteries. If multiple buttons are pressed the clock will set to the time zone selected last. If no time zone is

selected the clock will default to Pacific Time. Another time zone can be selected during or after the clock has set

itself. Your clock can only set itself to one of the four time zones stated above. For time zones outside of PT,

MT, CT or ET you must manually set the time using the Manual Time set button on the back of the movement.

When the battery is installed the second hand will advance eight seconds (two seconds per step x four

steps). The clock is now searching for a signal. For the initial setting it is recommended to stand the clock in an

upright position near a window. Within five minutes the clock will either receive the WWVB signal and set itself to

the exact time, or it will determine that the signal is not receivable at its current location and time of day. If a

signal is not receivable it will fast-forward the hands to the 4, 8, or 12 o’clock position and search for WWVB each

hour until a signal is received. If the time is manually set the clock will continue to periodically search for a signal

and automatically reset the hands when the signal is received.

Select a location to place your radio controlled clock where it will be at least six feet away from a TV,

computer, air conditioner or other household electrical appliances. The optimal location is near a window.

Windows facing Colorado providing the best signal. The WWVB time signal will easily penetrate Masonry and

wood framed buildings. WWVB will penetrate almost every residential building and most steel buildings if they

have adequate windows. It is not possible, however, for WWVB to penetrate most indoor shopping malls and

rooms in the center of large office buildings that do not have windows. In buildings that WWVB cannot penetrate

you may set the time using the manual time set button. When the clock is exposed to the WWVB signal it will

automatically set the hands to the exact time.

La Crosse Technology clocks do not receive or process radio controlled time signals from Germany’s DCF

77, Japan’s J Ga AS, or England’s MSFs atomically regulated transmitters. La Crosse Technology clocks can be

manually set and used anywhere.

For more information on the NIST and radio controlled time, see www.boulder.nist.gov/timefreq/

Troubleshooting

The wonderful advantage of owning a La Crosse Technology radio controlled clock is that it is virtually trouble

free. If the clock receives a clear signal it will set itself perfectly. If it does not receive a signal consider the

following:

Battery - The La Crosse Technology clock must have a fresh battery to receive and process the time signal.

Location - Try a different location, ideally near a window. It should be at least six feet from computers, TVs, air

conditioners, other Radio-Controlled clocks and other electrical appliances that cause interference.

Weather - Electrical storms between you and Colorado during the night will interfere with the WWVB signal.

Although we cannot control the weather we can help you predict it (see www.lacrossetechnology.com).

Daylight Savings Time

The National Institute of Standards and Technology and WWVB encode a special DST “bit” in the WWVB

transmission for DST. Your La Crosse Technology clock will read this information and automatically advance the

hands one hour in the spring and eleven hours in the fall.

Arizona and Indiana

If you live in an area that does not recognize DST you must press the (unmarked) DST button for one second to

deactivate your clock’s DST program. To reactivate the DST program simply press the DST button again for one

second.

Frequently Asked Questions

Q. How long will the battery last?

A. A good AA alkaline battery will last over one year. If your clock is located in an area with little interference

where it can quickly receive a signal the battery can last much longer than one year.

Q. Can a La Crosse Technology clock be used outdoors?

A. Yes, but only in a dry environment and in a temperature range between 41 F and 131 F. The clock is NOT

water-resistant.

Q. Can the La Crosse Technology clock be wired to control timing circuits?

A. No.

Q. Why does the second hand move only once every two seconds?

A. When the battery drops below 1.25 volts the clock indicates that it is time to change the battery by advancing

the second hand in two second steps. The operating voltage range is 1.25 to 1.75 volts.

WARRANTY INFORMATION

La Crosse Technology provides a 1-year warranty on this product. Contact La Crosse Technology immediately

upon discovery of any defects covered by this warranty.

Before sending the unit in for repairs, contact La Crosse Technology. The unit will be repaired or replaced with

the same or similar model.

This warranty does not cover any defects resulting from improper use, unauthorized repairs, faulty batteries, or

the units’ inability to receive a signal due to any source of interference.

LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL,

PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF

THIS UNIT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC

INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDRENS’ REACH.

This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States

do not allow the exclusion of consequential or incidental damages; therefore the above exclusion of limitation may

not apply to you.

For warranty work, technical support, or information contact

La Crosse Technology

1116 South Oak Street

La Crescent, MN 55947

Phone: 507.895.7095

Fax: 507.895.8000

e-mail

[email protected]

(warranty work)

[email protected]

(information on other products)

Website

www.lacrossetechnology.com

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE

FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

processed using electronic, mechanical or chemical procedures without written permission of the publisher.

This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked

and corrections made in the next issue. We accept no liability for technical mistakes or printing errors, or their

consequences.

All trademarks and patents are acknowledged.

Inhaltsverzeichnis

Andere La Crosse Technology Uhr Handbücher

La Crosse Technology

La Crosse Technology BBB86118v3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-6118 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-1235UA-SS Bedienungsanleitung

La Crosse Technology

La Crosse Technology 433-3256W Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-54667 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 513-1417ALv4 Abmessungen

La Crosse Technology

La Crosse Technology 513-113 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3161 Installationsanleitung

La Crosse Technology

La Crosse Technology WT-3181PLX1 Abmessungen

La Crosse Technology

La Crosse Technology WS-8418AL-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-8100 Technisches Datenblatt

La Crosse Technology

La Crosse Technology Wattz 2.0 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8008U Installationsanleitung

La Crosse Technology

La Crosse Technology 513-1211 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 512-1422 Series Abmessungen

La Crosse Technology

La Crosse Technology WT-3144S Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3129Bx1 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-3051B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3126H Handbuch

La Crosse Technology

La Crosse Technology WT-8112U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 512-1422WH Bedienungsanleitung

La Crosse Technology

La Crosse Technology 513-1417CHv2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3129B Bedienungsanleitung

La Crosse Technology

La Crosse Technology BBB84022 Abmessungen

Beliebte Uhr Handbücher anderer Marken

Silicon Laboratories

Silicon Laboratories SI5324 Bedienungsanleitung

Heathkit

Heathkit GC-1005 Bedienungsanleitung

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Bedienungsanleitung

Andrew O'Malley

Andrew O'Malley DOTKLOK Bedienungsanleitung

ALGE-Timing

ALGE-Timing ASC3 Bedienungsanleitung

Bodet

Bodet Profil 960 Bedienungsanleitung

Nixie Clock

Nixie Clock Divergence Meter Bedienungsanleitung

Mini Gadgets

Mini Gadgets MCPro Bedienungsanleitung

Casio

Casio TMR-200 Bedienungsanleitung

Progetti

Progetti ILTEMPOSTRINGE Handbuch

BVItech

BVItech BV-101 Bedienungsanleitung

Progetti

Progetti KALIMERO Handbuch

Sharp

Sharp SPC900 Bedienungsanleitung

Datexx

Datexx DF0063 Bedienungsanleitung

LG LEC-005 Bedienungsanleitung

IKEA

IKEA ROTBLÖTA Bedienungsanleitung

U-Line

U-Line Н-2811 Bedienungsanleitung

Digiview

Digiview RC305EL Bedienungsanleitung