LaMotte DO 6 PLUS Bedienungsanleitung
2
PREFACE
This manual serves to explain the use of the DO 6 PLUS hand held
meter.
This manual functions in two ways: f rst as a step by step guide to
operating the meter; second, as a handy reference guide.
This manual is written to cover as many anticipated applications of the
DO 6 PLUS meter as possible. If there are questions about the use of this
meter contact the LaMotte Tech Service Department.
LaMotte Company will not accept any responsibility for damage or
malfunction to the meter caused by improper use of the instrument.
The information presented in this manual is subject to change without
notice as improvements are made, and does not represent a commitment
on the part of LaMotte Company.
WARNING! This set contains chemicals that
may be harmful if misused. Read cautions on
individual containers carefully. Not to be used by
children except under adult supervision.
3
TABLE OF CONTENTS
1. INTRODUCTION 5
2. GETTING STARTED 6
2.1 Description of Keypad Functions 6
2.2 Description of LCD Annunciators 7
2.3 Inserting & removing the Rubber Boot/Stand 7
2.4 Inserting New Batteries 8
2.5 Battery Replacement 8
2.6 Connecting the Probe 9
2.7 Electrode Information 10
2.8 Switching the Meter On 11
2.9 Changing Mode 11
3. CALIBRATION 12
3.1 General Information 12
3.2 Temperature Calibration 13
3.3 % Saturation Calibration 14
3.3.1 100% Calibration 14
3.3.2 0% Calibration 15
3.4 mg/L or ppm Calibration 16
4. MEASUREMENT 17
4.1 Temperature Compensation 17
4.2 Taking Measurements 18
4.3 Pressure & Salinity Compensated Measurements 18
4.4 Holding a Reading 19
5. SETUP 19
5.1 Conf guration Menu (COF.1) 23
5.2 Automatic Temperature Compensation (A.ATC) 23
5.3 Selection of mg/L or ppm (b.DO) 24
5.4 Calibration Data (CAL.2) 24
5.5 Electrode Data (ELE.3) 25
5.6 Automatic Shut Off (AtO.4) 26
5.7 Reset to Factory Default (rSt.5) 26
5.8 % Saturation Offset Adjustment (OFS.6) 27
5.9 Pressure & Salinity Adjustment 29
6. PROBE MAINTENANCE 30
6.1 Cap and Electrolyte Replacement 31
6.2 Electrolyte Solution 32
7. TROUBLESHOOTING 32
8. ERROR MESSAGES 33
9. FACTORY DEFAULT SETTINGS 34
10. SPECIFICATIONS 35
4
11. REPLACEMENT PARTS AND ACCESSORIES 36
12. DISSOLVED OXYGEN THEORY 37
Measurement Units 37
What Is Being Measured? 37
Air Calibration 38
Applications 38
13. WARRANTY 39
14. REPAIRS 40
5
1. INTRODUCTION
The DO 6 PLUS microprocessor-based handheld meter is economical
and easy to use. It has a large custom LCD (Liquid Crystal Display) for
clear and easy reading.
The DO 6 PLUS offers measurement of dissolved oxygen (DO) as
percentage saturation or concentration. Temperature measurement is
available in degrees Celsius. The meter ensures accurate measurement
of the dissolved oxygen values through the temperature, barometric
pressure and salinity compensation features.
Meter kits include a dissolved oxygen probe, ref ll solution, a rubber
boot/stand, 4 alkaline “AAA” batteries and instruction manual. For
additional information, see Section 11 — Replacement Parts and
Accessories.
Read this manual thoroughly before operating the meter.
6
2. GETTING STARTED
2.1 Description of Keypad Functions
The meter has 6 keys on a splash-proof keypad. Some buttons have
multiple functions depending on the mode of operation.
ON/OFF Powers meter on and off. Meter starts up in the
measurement mode that was last used.
CAL Enters into calibration mode. Pressing while in calibration
mode will abort calibration without conf rming value.
MODE Selects desired measurement mode. When pressed
simultaneously with ON/OFF, it will go to the SETUP
mode.
HOLD Freezes measured reading. Press again to resume live
reading.
ENTER Conf rms calibration value in calibration mode and
conf rm selections in SETUP mode.
Increments/decrements values during calibration mode or
scroll through SETUP menus. Set offset adjustments and
conf guration settings.
7
2.2 Description of LCD Annunciators
The meter has a large custom LCD that consists of 4-digit segments plus
annunciators for percentage saturation (%), concentration (mg/L or ppm)
and Temperature in degrees Celsius (T).
Other annunciators include “A” (when the ATC function is activated),
“CAL” (when meter is in calibration mode) and low battery condition.
milligram per litre
(Concentration Mode)
mg/l
ppm
%
TA
14-segment Liquid Crystal Display
Low Battery annunciator
Calibration Mode
Annunciator
CAL
Temperature Mode
A T C annunciator
parts per million
Percentage
(Percentage Saturation
Mode)
2.3 Inserting & Removing the Rubber Boot/Stand
1. To remove the meter from the rubber boot, push out the bottom
edge of the meter until it is completely out of the boot. Ensure
that the probe cables are not connected. See Figure 1.
2. To insert the meter into the rubber boot, slide in the top of the
meter before pushing the bottom edge of the meter down to set it
into position. Lift up the stand at the back of the meter for bench
top applications. See Figure 2.
Figure 1 Figure 2
8
2.4 Inserting New Batteries
The battery compartment is found at the back of the instrument. To open
the battery compartment, push the cover in the direction of the arrow and
lift up. Note the polarity of batteries before inserting them into position.
After the batteries have been replaced, reposition the cover and press
down until it locks.
2.5 Battery Replacement
A low battery annunciator on the LCD alerts when the battery power is
running low. Caution: Power off the meter before replacing the batteries.
%
Low Battery Condition
9
2.6 Connecting the Probe
1. To connect the probe, align the connector slots with the posts of
the meter socket and rotate the connector clockwise until it locks.
2. To remove the probe, rotate the connector in an anti-clockwise
direction until it unlocks, and slide the connector off the socket.
3. Insert the mini phono jack of the temperature sensor into the
socket on the meter as shown below.
2.5 mm mini phono
jack for
temperature sensor
BNC connector
for DO probe
10
2.7 Electrode Information
The DO 6 PLUS includes a galvanic DO electrode
which does not require warm-up. It generates
a millivolt signal proportional to the amount of
oxygen in the solution.
The probe has a dual cable; a BNC connector
for DO measurement and a phono jack plug
for temperature. The sensor utilizes a cathode,
anode, and electrolyte that are separated from
the sample by an oxygen permeable membrane.
The membrane is pre-assembled and f xed to a
detachable cap. The pre-assembled cap design
allows simple replacement and fast conditioning.
The probe is lightweight and includes a built-in
temperature sensor. The epoxy body of the probe
is 12mm in diameter while the detachable Noryl
cap is 16mm in diameter. The compact sensing
area reduces air entrapment resulting in quick,
accurate, and stable readings.
The pre-assembled cap must be completely
submersed in the solution to obtain an accurate
reading. Provide simple stirring for best results—
ideally achieve a minimum water f ow rate of 2 inch/second on the
membrane. The probe is not recommended for use in samples outside of
the range of 0 to 50 °C.
Shaking the probe will aid in removing bubbles, if needed, before taking
a reading. When calibrating in air, shake to remove water from the
membrane.
The membrane is thin and can not be repaired if it is damaged. Use care
to protect from scratches, abrasions, or contact with solids. For best
results keep the membrane clean by rinsing it after daily use. See Section
6 – Probe Maintenance.
Detachable
Pre-membraned Cap
(Probe Sensing Area)
16 mm
12 mm
Inhaltsverzeichnis
Andere LaMotte Messgerät Handbücher
LaMotte
LaMotte 6 Series Bedienungsanleitung
LaMotte
LaMotte DC1500 CHLORINE Bedienungsanleitung
LaMotte
LaMotte ColorQ DW Bedienungsanleitung
LaMotte
LaMotte Tracer PockeTester Bedienungsanleitung
LaMotte
LaMotte Tracer 1749 Bedienungsanleitung
LaMotte
LaMotte SMART3 Bedienungsanleitung
LaMotte
LaMotte SMART Spectro Bedienungsanleitung
LaMotte
LaMotte COD3 Plus Bedienungsanleitung
LaMotte
LaMotte DC1500 CHLORINE Bedienungsanleitung
LaMotte
LaMotte 2020we Bedienungsanleitung
LaMotte
LaMotte DC1500 CHLORINE Bedienungsanleitung
LaMotte
LaMotte DC1500 PHOSPHATE Bedienungsanleitung
LaMotte
LaMotte WaterLink Spin Touch Bedienungsanleitung
LaMotte
LaMotte DC1500 CHLORINE Bedienungsanleitung
LaMotte
LaMotte DC1500 Copper Bedienungsanleitung
LaMotte
LaMotte WaterLink SpinTouch 3580-AU Bedienungsanleitung
LaMotte
LaMotte DC1500 CHLORINE Bedienungsanleitung
LaMotte
LaMotte 1200-MN Bedienungsanleitung
LaMotte
LaMotte Tracer 1749-KIT-01 Bedienungsanleitung
LaMotte
LaMotte DC1500-CL Bedienungsanleitung
