Landscape Forms Ashbery Bedienungsanleitung

Surface Mount

Included items:

Fig. 1 –Minimum footing recommendation

Fig. 4 –conduit clearance

Tools Required

•Safety glasses

•Wiring tools and connectors

•Anchoring hardware –(4) Ø5/16 [8mm] (maximum), with bolt head and washer not

to exceed dimensions in Fig. 3. Maximum washer O.D. is 0.734”.

•Hammer drill

•13mm ratchet wrench

•2.5mm hex key

ASSEMBLE WITH CARE! Pangard IIPolyester Powdercoat is a strong, long-lasting finish. To protect

this finish during assembly, place unwrapped powdercoated parts on packaging foam or other non-

marring surface. Do not place or slide powdercoated parts on concrete or other hard or textured

surface –this will damage the finish causing rust to occur. Use touch-up paint on any gouges in the

finish caused by assembly tools.

LIGHTING LAYOUT RECOMMENDATIONS:

Refer to the Product Data Sheet

Installation Guide

Ashbery Path Light

www.landscapeforms.com Ph: 800.521.2546

Date: March 19, 2021

Page 1 of 2

1x – Light

assembly

1x – anchor

template

2x – M8 x

25mm hex

head cap

screw

2x – M4 x

14mm

button head

cap screw

2x – M8

washer

Fig. 2 –Recommended setback

from sidewalk

SIDEWALK

Fig. 3 –Base plate section view

FRAME

CASTING

BASE

CASTING

Hardware ships installed on unit

INSTALLATION PROCEDURE FOR PATHLIGHT:

1. Prepare footing as required by local codes, see Fig. 1 and Fig. 2 for

recommendations.

2. Set wooden anchor template in position over conduit.‘F’ on the template indicates

the Front of the unit. Make sure the ‘F’ faces up.

3. Mark four anchor hole locations and remove the template.

4. Drill holes according to anchor size and depth. Clear holes of debris.

5. Using the 2.5mm hex key, remove two screws to remove cabinet cover as shown in

Fig. 5.

6. Using the 13mm ratchet wrench, remove the two screws that attach the unit frame

to the base plate, as shown in Fig. 6.

7. Set base plate in position, ensuring that base sits flat on concrete, and install anchors

according to anchor manufacturer’s recommendations. The base plate is marked to

indicate the front of the unit.

8. Set unit body over base plate, see Fig. 8. Attach using two screws as shown in Fig. 6.

9. Make wiring connections.

10. Install cabinet cover as shown in Fig. 5.

Fig. 7 –Base plate

Landscape Forms is not responsible for site preparation and footings. Footing

recommendations are included in these instructions.

Installation Guide

Ashbery Path Light

www.landscapeforms.com Ph: 800.521.2546

Page 2 of 2

Date: March 19, 2021

Fig. 5 –Remove access panel Fig. 6 –Remove/install

base to body

ANCHORING

HARDWARE

NOT INCLUDED

M8 x 25mm

HEX CAP

SCREW

PORTION OF UNIT FRAME IS

NOT SHOWN FOR CLARITY

Fig. 8 –Install unit body over

installed base plate

PROCEDURE FOR WIRING ASHBERY PATHLIGHT:

The Ashbery path light is assembled at the factory. The light cartridge is mounted into

the head of the pole and will not need to be removed during installation. The LED

cartridge is wired to the driver (located in the cabinet) at the factory.

The following schematics are to be used to connect the unit to line voltage. It is the

responsibility of the installer to make sure that all connections are made in accordance

with the NEC and local building codes. Connection hardware not included.

Fig. 9 –Ashbery Pathlight wiring schematic

WARNING!: LED cartridge and driver are not rated for

connection or disconnection while energized. Doing so

may damage LEDs and will void the warranty.

Disconnect incoming power before making or breaking

any electrical connections.

Andere Landscape Forms Außenleuchte Handbücher

Landscape Forms

Landscape Forms Annapolis Bollard Bedienungsanleitung

Landscape Forms

Landscape Forms Lo-Glo Bedienungsanleitung

Landscape Forms

Landscape Forms MultipliCITY Path Light Bedienungsanleitung

Landscape Forms

Landscape Forms FGP Bedienungsanleitung

Landscape Forms

Landscape Forms Signal Bedienungsanleitung

Landscape Forms

Landscape Forms FGP Path Light Bedienungsanleitung

Landscape Forms

Landscape Forms Connect 2.0 Bedienungsanleitung

Landscape Forms

Landscape Forms Profile Area Light BW402 Bedienungsanleitung

Landscape Forms

Landscape Forms Torres Bedienungsanleitung

Landscape Forms

Landscape Forms Profile BW103-2 Bedienungsanleitung

Landscape Forms

Landscape Forms Hawthorne Bedienungsanleitung

Landscape Forms

Landscape Forms Ashbery Bedienungsanleitung

Landscape Forms

Landscape Forms Torres Bedienungsanleitung

Landscape Forms

Landscape Forms Connect 2.0 Bedienungsanleitung

Landscape Forms

Landscape Forms Annapolis Bollard Bedienungsanleitung

Landscape Forms

Landscape Forms Typology Bedienungsanleitung

Landscape Forms

Landscape Forms Motive Bedienungsanleitung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung