Landtek GM-06 Bedienungsanleitung

www.landtek.com.cn

www.landteknet.com

1.Feasures:

designed and manufactured in

accordance with international

standard ASTM D523, ASTM D1455,

ASTM C346, ASTM C584, ASTM

D2457, DIN EN ISO 2813, DIN

67530, EN ISO 7668, JIS Z 8741,

MFT 30064, TAPPI T 480, GB

9754, GB/T13891, GB 7706 and GB

8807. Its technical parameters

conform with JJG 696-2002.

Flexible use with its separate probe.

2.Applications:

Widely used in Floor maintenance,

Surface cleaning quality control,

Stone and tile gloss measurement,

Checking printed matter, Quality

control of paint and ink, Polished

metal surface , measurement

(chrome plating), Inspection of paint

protection and waxing, Auto-body

p a i n t i n s p e c t i o n , S u r f a c e

inspection of plastic moldings,

Evaluation of detergents and

washers,Checking masonry and

building exteriors.

3.TECHNICAL SPECIFICATIONS

Display: 4 digits backlit LCD

Measuring geometry: 60 Degrees

Range: 0.1 to 200 gloss units

Accuracy: ± 1.0 gloss unit

( against reference standard )

Resolution: 0.1 gloss unit

Repeatability: ± 0.5 GU

(0 ... 99.9)

Measuring area: 7x14mm ellipse

Data memorized: 25 4 groups

Data output: RS 232 C serial

interface

Power supply: 4x1.5 V AAA

battery

Dimensions: main unit:156

x67x28mm

Separate sensor:58x28x108mm

Weight: about 300g ( including

fitted batteries )

Working condition:

Temperature range 0 - 40°C

Humidity up to 85%

4.Accessories

Carrying case ........1 pc

Operation manual .........1 pc.

External probe..............1 pc.

Holder with calibration

standard………..........1 pc.

Optic cleaning cloth…1pc.

5.Optional accessories

Cable & software for RS232C.

USB adaptor. Bluetooth interface.

6-1Sensor Plug 6-2Display

6-3Number Memorized 6-4Measuring key

6-5Delete key 6-6Read/Up key

6-7CAL/Down key 6-8Power key

6-9Angle indicate

6-10Jack for RS2 32 interface

6-11Measurement Aperture

6-12Protective Cap with calibration

standard

6-13Battery cover/compartment

7.Power ON / OFF

Press the key to power on the

meter. To turn it off, just press

this key again. This meter

is powered with 4 x1.5vAAA dry cell

batteries. To install or replace the

batteries, just remove the battery

cover and Insert the new cells in the

battery cartridge. Pay attention to

the battery pole.

8.Calibration:

Lay the main unit into the holder

with calibration standard of high

gloss black tile. Take a reading

by pressing the MEAS key.

Compare the measured value with

the value marked on the tile. If it

matches the value on the tile holder,

the instrument is within calibration

and ready for use. If the measured

value

does not match the assigned value,

just press the CAL key.

It is n ecessary to inspect t he

condition of the calibration tile and

instrument optics before each

calibration. Any dust or debris on

the optic should be blown from the

lenses using dry clean air, the

optics must not be touched. If there

are any permanent marks or

scratches on th e lense s , t h e

instrument is no longer suitable for

measuring and should be returned

to an authorized service center.

The calibration tile must be

perfectly clean from smears and

scratches before attempting

calibration. Fingerprints and dust

can be removed with the supplied

optic cleaning cloth.

GLOSSMETER

GM-06

6-1

6-2

6-6 6-13

6-3

6-9 6-7

6-4

6-10

6-11

6-12

MEAS

DEL CAL

6-8

6-5

6.FRONT PANEL DESCRIPTIONS

GLOSSMETER

GM-06

www.landtek.com.cn

www.landteknet.com

9.Measurement

Remove the holder an d la y th e

Measurement Aperture just

against the position that you want

to measure. Take a

measurement by pressing the

MEAS key . The reading on the

Display Screen within 2

seconds is the gloss value of

that position. Meanwhile the

result is stored into

memory automatically.

When the instrument is placed on a

sample the aperture is hidden, the

centre of the measurement area can

be pinpointed by the intersection

of the arrows marked on the front

of the instrument case with those on

the side.

10.Data Memorizing

When taking measurements, all

values will be stored automatically

in memory and the number of

stored reading is accordingly

increased by

10.1 The gloss meter can store up to

2 5 4 g r o u p s o f d a t a w i t h

measurement conditions. If the

memory is full, the tester will auto

save the new reading and discard

the oldest one. That means the

tester only hold the last 254 groups

of data in memory.

11.Memory Recall

Under the measuring mode marked

by ‘M’ on the display , press the

key to enter into mode of viewing

stored values marked by ‘R’.

Press key or key to recall

stored values forwards and

backwards. To return to t h e

measurement state, just press any

key otherthan o r key .

12.Delete data in memory

In the measurement state marked by

‘M’ on the display , the new

reading can be deleted by pressing

key DEL , and the number of stored

reading is accordingly decreased by

1. To clear memory, just press and

hold DEL key for 3 seconds till the

number of stored reading becomes

000.

13.Download to PC

This meter can communicate with a

PC by optional USB or RS232C

cable and software. All the

memorized data can download to

your PC every time when in a

measurement state marked by

when you press RD / key to

enter the viewing memorized state.

14.Auto Power Off

The instrument features an auto

power off function designed to

conserve battery life. If the tool is

idle (neither measuring nor any key

operation) for 3 0 minutes, it will

turn itself off.

15.Battery Replacement

When the battery symbol appears on

the display, it is time to replace the

batteries. Slide the Battery Cover

away from the instrument and

remove the batteries. Install

batteries paying careful attention to

polarity.

Notes:

* The holder removed from the

main unit should be kept in a

safe and clean place to prevent

from damage or pollution.

* While measuring please keep

environment light from directly

irradiating into the measurement

aperture.

If necessary, especially under

strong light, shade it with a

piece of light-tight cloth.

* A big temperature difference

between environment and meter

would badly affect measuring

accuracy. In such a case, please

wait for a period of time till the

temperature get to a balance and

then calibrate the meter again.

* If measurement operation lasts a

long time., for example an hour

or more, it is necessary to

recalibrate the meter

MEAS

CAL

Andere Landtek Messgerät Handbücher

Landtek

Landtek PH-ORP 2000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung