Lanner FW-8756 Bedienungsanleitung

Network

Application Platforms

Hardware platforms for next generation networking infrastructure

FW-8756

User's Manual

Publication date:2011-03-23

About

Network Application Platforms

Overview

Icon Descriptions

The icons are used in the manual to serve as an indication

of interest topics or important messages. Below is a

description of these icons:

NOTE: This check mark indicates that

there is a note of interest and is something

that you should pay special attention to

while using the product.

WARNING: This exclamation point

indicates that there is a caution or

warning and it is something that could

damage your property or product.

Online Resources

The listed websites are links to the on-line product

information and technical support.

Resource Website

Lanner http://www.lannerinc.com

Product Resources http://assist.lannerinc.com

RMA http://eRMA.lannerinc.com

reserved. The original manufacturer reserves the right to

make improvements to the products described in this

manual at any time without notice.

No part of this manual may be reproduced, copied,

translated or transmitted in any form or by any means

without the prior written permission of the original

manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original

manufacturer assumes no responsibility for its use, nor for

any infringements upon the rights of third parties that

may result from such use.

Acknowledgement

Intel, Pentium and Celeron are registered trademarks of

Intel Corp.

Microsoft Windows and MS-DOS are registered trademarks

of Microsoft Corp.

All other product names or trademarks are properties of

their respective owners.

Compliances

This product has passed the CE test for environmental

specifications. Test conditions for passing included the

equipment being operated within an industrial enclosure.

In order to protect the product from being damaged by

ESD (Electrostatic Discharge) and EMI leakage, we strongly

recommend the use of CE-compliant industrial enclosure

products.

FCC Class A

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required

to correct the interference at his own expense.

TTaTTable of Contentsbeable of Contents

Chapter 1: Introduction 1

System Specication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Front Panel Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Rear Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2: Hardware Setup 5

Preparing the Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing a CompactFlash Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CPU and the Heat Sink Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Riser Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front Ethernet Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 3: Motherboard Information 8

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Motherboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Appendix A: Programming Watchdog Timer 13

Appendix B: Setting up Console Redirections 14

Appendix C: Programming the LCM 15

Appendix D: Programming LAN Bypass 16

Appendix E: Driver Installation 17

LAN Adapters Driver Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Windows Operating systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Linux. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

VGA Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Windows Operating systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Appendix F: Terms and Conditions 20

Warranty Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

RMA Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Introduction

Chapter 1

Network Application Platforms

Chapter 1:

Introduction

Thank you for choosing the FW-8756. The FW-8756 is a

1U network communication appliance that is designed

to meet your demand for quality network application

platform.

The FW-8756 supports different class of Intel 90 nm CPUs

packaged in LGA 775 for user selection including Intel

Core2 Quad, Intel Core 2 Duo, and Intel Celeron.

The FW-8756 comes with 1 FE and 6 Gb Ethernet ports

with three pair capable to be an abnormal state packet

dual latch bypass (the newest Generation 3 bypass). In

addition, with the Lanner riser card, an optional expansion

LAN module can be added.

Here is the list of some key features of the FW-8756

system:

Built on Intel chipset G41 and ICH7R•

Two COM ports: 1 x RJ45 Serial Console port (CISCO•

TYPE) and 1 pin header on board (2x5)

Two USB 2.0 Ports on the front panel and one USB2.0•

pinheader (2x5)

one 3.5”SATA II HDD or two 2.5”SATA II•

One VGA pin header (Sku A only)•

One IPMI management port through the OPMA•

connector (SKu B only)

One PCI-Ex8 for expansion riser card•

3 pairs of the Generation 3 bypass ports•

Please refer to the chart below for a summary of the

system’s specifications.

System Specification

Feature Description

Form Factor 1U Rackmount

Platform

Processor

Supports Intel Core2 Quad,

Core2 Duo, PentiumD, Celeron

Processors, LGA775

Chipset Intel G41 + ICH7R

Embedded Accelerator by request

System Memory

Technology DDR3 800/1066/1333 MHz

Max Capacity 4GB

Socket 2 x 240P DIMM

OS Support Windows, Linux

Storage

HDD Bay(s) 1 x 3.5” or 2 x 2.5”

Storage Interface 2 x Serial ATA,

1 x CompactFlash

Networking

Ethernet Port Density

6 x RJ45 GbE Onboard

1 x RJ45 FE

1 x Optional Module

Controller 6 x Intel 82574L

1 x Intel FE LAN

Network Module(s) 1 x Tray to t Lanner 8800

Series Modules

Bypass 3 x pairs of LAN bypass

I/O Interface Console 1 x RJ45

USB 2 x USB 2.0

IPMI via OPMA slot Optional

Expansion PCI 1 x Mini-PCI

Cooling

Processor 1U Passive heatsink with 3

cooling fans

System 1 x Cooling Fan with Smart Fan

Environmental

Parameters

Temperature, ambient

operating / storage 0ºC~40ºC / -20ºC~60ºC

Humidity (RH), ambient

operating and non-

operating

5 ~ 95%, non condensing

Miscellaneous

LCD Module 2 x 20 Character

Optional Graphic LCM

Watchdog Yes

Internal RTC with Li

Battery Yes

Physical

Dimensions

Dimensions (WxHxD) 431 x 44.4 x 395 mm

Weight 6 kg (13.2 lbs)

Power

Type / Watts 1U ATX /200W

Input AC 90~264V@47~63Hz

Output

+5V output: 1V min, 12V max;

+3.3V output: 1V min, 14V

max;

+12V output 1V min, 14V max

Approvals &

Compliance

CE Emission, FCC Class A,

RoHS

Introduction

Chapter 1

Network Application Platforms

Package Contents

Your package contains the following items:

FW-8756 Network Security Platform•

Power cable•

1 crossover Ethernet cable (1.8 meters)•

1 straight-through Ethernet cable (1.8 meters)•

1 RJ-45 to DB-9 female console cable (• Cisco type)

CPU heat sink•

1 threaded-screw set•

1 short ear-bracket set•

Front name-plate label•

Drivers and user’s manual CD.•

Ordering

Information

FW-8756A STD 1FE + 6GbE ports, with 3

pairs bypass

FW-8756B

STD 6GbE ports, with 3 pairs

bypass & IPMI

only used with 2.5” HDD

Introduction

Chapter 1

Network Application Platforms

Front Panel Features

F1 Power/Status/HDD LED

Power: If the LED is on it indicates that the system is powered on. If it is off, it indicates that the system is powered off.

Status: If the LED is green, it indicates that the system’s operational state is normal. If it is red, it indicates that the system

is malfunctioning.

HDD: If the LED is on, it indicates that the system’s storage is functional. If the LED blinks, it indicates data access activities.

If it is off, it indicates that there is no hard disk present or functional.

F2 System Panel: LCD System Panel

The LCD System Panel can be programmed to display operating status and configuration information. For more details

or sample programming code, please refer to the User’s Manual CD.

F3 Reset Switch

The reset switch can be used to reboot the system without turning off the power.

F4 Console Port

By using suitable rollover cable or RJ-45 to DB-9 Female (Cisco console cable), you can connect to a computer terminal

for diagnostic or configuration purpose. Default terminal Configuration Parameters: 115200 baud, 8 data bits, no parity,

1 stop bit , no flow control.

F5 Two USB 2.0 Ports

It connects to any USB devices, for example, a flash drive.

F6 Management Port

This FastEthernet port can be connected for configuration or troubleshooting purpose. A conformity with IPMI (Intelligent

Platform Management Interface) can be implemented on this port through the Open Platform Management Architecture

(OPMA) interface.

F7 6 Gigabit LAN ports

Right LED:If the LED is orange, it indicates that the connection speed is 1000Mbps. If the LED is green, it indicates that the

connection speed is 100Mbps. And if it is off, it indicates that the speed is 10Mbps.

Lefts LED: If the LED is on, it indicates that the port is linked. If it blinks, it indicates there is traffic.

Using suitable RJ-45 cable, you can connect FW-8756 system to a computer, or to any other piece of equipment that has

an Ethernet connection; for example, a hub or a switch. Moreover, 3 pair (LAN1-LAN2, LAN3-LAN4, LAN5-LAN6) can be

configured as LAN Bypass when failure events occur. This feature can implemented in hardware in conjunction with a

watch dog timer functionality. Refer to Appendix D for a sample implementation of this feature.

F8 LAN 7, LAN 8: An optional expansion of LAN switch. This expansion of LAN switch can add up to additional 8 Ethernet

ports.

Note:

The availability of LAN Bypass varies depending on the model.

The number of LAN ports varies depending on the model.2.

Manage LAN1 LAN2 LAN3 LAN4 LAN5 LAN6

F3 F4 F5

F2 F7 F8

Introduction

Chapter 1

Network Application Platforms

R1 System Fan, CPU Fans 1, 2, 3

R2 Power-on Switch

It is a switch to turn on or off the power.

R3 AC Power-in socket

It is a 200W ATX power supply unit with input range of 90~264V@47-63Hz.

R4 Power Supply Fan

Rear Panel Features

R1 R2 R3 R4

Introduction

Chapter 2

Network Application Platforms

Chapter 2:

Hardware Setup

Preparing the Hardware Installation

To access some components and perform certain service

procedures, you must perform the following procedures

first.

WARNING: To reduce the risk of personal injury,

electric shock, or damage to the equipment,

remove the power cord to remove power from the

server. The front panel Power On/Standby button

does not completely shut off system power.

Portions of the power supply and some internal

circuitry remain active until AC power is removed.

Unpower the FW-8756 and remove the power cord.1.

Unscrew the screws (three on each side and two on2.

the rear) from the top cover of the FW-8756 System.

Slide the cover backwards and open the cover3.

upwards.

Installing the System Memory

The motherboard supports DDR3 memory that features

data transfer rates of 800, 1066, and 1333 MHz to meet the

higher bandwidth requirements of the latest operating

system and Internet applications. It comes with two

Double Data Rate three (DDR3) Dual In-line Memory

Modules (DIMM) sockets.

Open the DIMM slot latches.1.

Install the DIMM.2.

Note:

All DIMMs installed must be the same speed1.

(DDR3 800, 1066, or 1333). Do not install DIMMs

supporting different speeds.

Installing the Hard Disk

The system can accommodate two 2.5” or one 3.5”Serial-

ATA disks. Follow these steps to install a hard disk into the

FW-8756:

Unscrew the 4 screws on the hard disk tray to take out1.

the hard disk tray from the system.

Place hard disk on the hard disk tray and align the holes2.

of the hard disk with the mounting holes on the tray.

Secure the hard disk with 4 mounting screws on the3.

hard disk tray.

Connect the Serial-ATA power and data disk cables4.

to the hard disk’s power and drive connectors

respectively.

Plug the Serial-ATA cable to the Serial-ATA Connector5.

on the main board.

Repeat steps 2 to 5 to install a second disk (if there is6.

one).

Put the hard disk tray with the installed hard disk back7.

to the system and secure it with the mounting screws.

Note:

The 3.5” disk tray also supports 2.5” HDD1.

installation. To do this, take off one side of the

tray first to make room for SATA cables. Attach the

HDD to the tray by fixing the screws to the slot

on the bottom of the tray.

FW-8756 SKU B can support2. only the 2.5” HDD.

Introduction

Chapter 2

Network Application Platforms

Installing a CompactFlash Card

FW-8756 provides one CompactFlash slot. Follow the

procedures bellow for installing a CompactFlash card.

Align CompactFlash card and the card slot with the1.

arrow pointing toward the connector.

Push the card to insert into the connector.2.

CPU and the Heat Sink Installation

The FW-8756 sever system is powered by the MB-8756

sever board, which comes with one ZIF type LGA775 CPU

socket.

Follow the procedures bellow for installing a CPU

Remove the CPU socket cap.1.

Press the load lever and release it from the retention2.

tab.

Lift the load lever and then the plate.3.

Align the cut-out of the CPU and the notch on the4.

socket. The CPU should fit perfectly into the socket.

Note that the CPU fits in the socket in only one

direction.

Close the plate and push the load lever to lock it back5.

to the retention tab.

Peel off the sticker on the CPU to expose the thermal6.

compound.

Put the heat sink on top of the installed CPU, and match7.

the screws with the screw holes on the board. Fasten

two screws which are opposite to each other at a time

and then the other two. It is easier this way because of

the springiness of the bracket.

Place the heat sink cover on top of the installed heat8.

sink and screw the three screws to fasten it on the

case.

3.5” HDD installation

( screw slots are on the

bottom of the tray)

3.5” HDD installation

Introduction

Chapter 2

Network Application Platforms

Align the riser card with the PCI-E golden finger1.

connector.

Insert the card into the connector firmly.2.

Fasten the screws to fix the card onto the board.3.

Riser Card Installation

Front Ethernet Module Installation

To install the front Ethernet module, take off the front1.

bezel first by unfastening the threaded screws at the

bottom of the case.

Insert the Ethernet module into the front expansion2.

slot.You should hear a click when the module connects

to the riser card.

Fasten the screw back on the bottom of the case to3.

secure the module on the system.

Note:

The CPU heat sink can only be installed in only1.

one orientation as shown in the picture.

To protect the CPU socket pins, retain the CPU2.

cap when the CPU is not installed.

Inhaltsverzeichnis

Andere Lanner Netzwerk-Hardware Handbücher

Lanner

Lanner NCA-5710 Bedienungsanleitung

Lanner

Lanner NCA-5540 Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

Lanner

Lanner NCA-4210 Bedienungsanleitung

Lanner

Lanner LWR-X8460 Bedienungsanleitung

Lanner

Lanner NCS2-VT04 Bedienungsanleitung

Lanner

Lanner IIOT-I531 Bedienungsanleitung

Lanner

Lanner NCA-1611A Bedienungsanleitung

Lanner

Lanner NCA-2510 Bedienungsanleitung

Lanner

Lanner NCA-2523 Bedienungsanleitung

Lanner

Lanner FX-3420 Bedienungsanleitung

Lanner

Lanner NCA-5210 Bedienungsanleitung

Lanner

Lanner LEC-3340 Bedienungsanleitung

Lanner

Lanner NCA-1515 Bedienungsanleitung

Lanner

Lanner NCA-1040 Bedienungsanleitung

Lanner

Lanner IIOT-I530 Bedienungsanleitung

Lanner

Lanner NCA-4220 Bedienungsanleitung

Lanner

Lanner NCA-1513 Bedienungsanleitung

Lanner

Lanner uCPE NCA-4020 Bedienungsanleitung

Lanner

Lanner NCA-6530 Bedienungsanleitung

Lanner

Lanner NCA-2522 Bedienungsanleitung

Lanner

Lanner ECA-4027 Bedienungsanleitung

Lanner

Lanner FW-8771 Bedienungsanleitung

Lanner

Lanner NCR-1510 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung

Cantek

Cantek NR310-4 Bedienungsanleitung