Lantech IES-22812F-2P Bedienungsanleitung

User Manual

V1.01

Nov-2010

Lantech

IES-22812F-2P

12 100FX + 8 10/100TX + 2 1000 SFP Industrial Power

Station L2 Plus Managed Switch

FCC Warning

This Equipment has been tested and found to comply with the limits for a Class-A

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. It may

cause harmful interference to radio communications if the equipment is not installed

and used in accordance with the instructions. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Content

Chapter 1 Introduction............................................ 1

1.1 Hardware Features ...................................................1

1.2 Software Features.....................................................2

1.3 Package Contents.....................................................4

Chapter 2 Hardware Description............................ 5

2.1 Physical Dimensions.................................................5

2.2 Front (LED) Panel .....................................................5

2.3 Rear Panel ................................................................6

2.4 LED Indicators...........................................................7

Chapter 3 Hardware Installation ............................ 9

3.1 Rack-mounted Installation.........................................9

3.2 Cabling....................................................................11

3.3 Wiring the Power Inputs..........................................14

3.4 Wiring the P-Fail Alarm Contact..............................15

Chapter 4 Network Application ............................ 16

4.1 X-Ring Application...................................................17

4.2 Coupling Ring Application.......................................18

4.3 Dual Homing Application.........................................19

Chapter 5 Console Management .......................... 20

5.1 Connecting to the Console Port ..............................20

5.2 Pin Assignment .......................................................20

5.3 Login in the Console Interface ................................21

5.4 CLI Management.....................................................22

5.5 Commands Level ....................................................22

Chapter 6 Web-Based Management ..................... 24

6.1 About Web-based Management .............................24

6.2 Preparing for Web Management.............................24

6.3 System Login...........................................................25

6.4 System Information .................................................26

6.5 IP Configuration ......................................................27

6.6 DHCP Server ..........................................................28

6.6.1 System configuration ..............................................29

6.6.2 Client Entries...........................................................30

6.6.3 Port and IP Bindings ...............................................31

6.7 TFTP .......................................................................32

6.7.1 Update Firmware ....................................................32

6.7.2 Restore Configuration.............................................33

6.7.3 Backup Configuration..............................................34

6.8 System Event Log...................................................35

6.8.1 Syslog Configuration...............................................35

6.8.2 System Event Log—SMTP Configuration...............37

6.8.3 System Event Log—Event Configuration................39

6.9 Fault Relay Alarm....................................................41

6.10 SNTP Configuration ................................................42

6.11 IP Security...............................................................46

6.12 User Authentication.................................................48

6.13 Advanced Configuration..........................................49

6.13.1 Broadcast Storm Filter............................................49

6.13.2 Aging Time.............................................................51

6.13.3 Jumbo Frame.........................................................52

6.14 Port Statistics ..........................................................53

6.15 Port Counters..........................................................55

6.16 Port Control.............................................................58

6.17 Port Trunk................................................................60

6.17.1. Aggregator setting.................................................60

6.17.2. Aggregator Information..........................................62

6.17.3. State Activity..........................................................66

6.18 Port Mirroring...........................................................68

6.19 Rate Limiting ...........................................................69

6.20 VLAN configuration .................................................70

6.20.1. Port-based VLAN ..................................................70

6.20.2. 802.1Q VLAN........................................................74

6.21 Rapid Spanning Tree ..............................................79

6.21.1. System Configuration............................................79

6.21.2. Port Configuration .................................................81

6.22 SNMP Configuration ...............................................83

6.22.1. System Configuration............................................83

6.22.2. Trap Configuration.................................................85

6.22.3. SNMPV3 Configuration.........................................86

6.23 QoS Configuration...................................................89

6.24 IGMP Configuration.................................................91

6.25 Pro-Ring ..................................................................93

6.26 LLDP Configuration.................................................95

6.27 Security—802.1X/Radius Configuration..................96

6.27.1. System Configuration............................................96

6.27.2. Port Configuration .................................................97

6.27.3. Misc Configuration.................................................98

6.28 MAC Address Table..............................................100

6.28.1. Static MAC Address............................................100

6.28.2. MAC Filtering.......................................................102

6.28.3. All MAC Addresses .............................................103

6.28.4. MAC Address Table—Multicast Filtering.............104

6.29 Access Control List ...............................................106

6.30 Factory Default......................................................107

6.31 Save Configuration................................................108

6.32 System Reboot......................................................109

Troubleshooting ................................................... 110

Appendix A — RJ-45 Pin Assignment................... 111

Appendix B — Command Sets.............................. 114

Commands Set List...........................................................114

System Commands Set.....................................................114

Port Commands Set..........................................................118

Trunk Commands Set .......................................................120

VLAN Commands Set.......................................................122

Spanning Tree Commands Set.........................................124

QOS Commands Set.........................................................127

IGMP Commands Set .......................................................128

Mac / Filter Table Commands Set.....................................129

SNMP Commands Set......................................................131

Port Mirroring Commands Set...........................................134

802.1x Commands Set......................................................135

TFTP Commands Set........................................................138

SystemLog, SMTP and Event Commands Set .................139

SNTP Commands Set.......................................................142

Pro-Ring Commands Set...................................................144

LLDP Command Set .........................................................145

Access Control List Command Set....................................146

Chapter 1 Introduction

1.1 Hardware Features

Switch Architecture Back-plane (Switching Fabric): 8Gbps

Packet throughput ability(Full-Duplex): 11.9Mpps @64bytes

Transfer Rate 14,880pps for Ethernet port

148,800pps for Fast Ethernet port

1,488,000pps for Gigabit Fiber Ethernet port

Packet Buffer 4Mbits

Mac Address 8K MAC address table

Flash ROM 4Mbytes

DRAM 64Mbytes

Jumbo Frame 9022bytes (for Gigabit ports)

Connector 10/100TX: 8 x RJ-45

100FX : 12 x SC

Gigabit Mini-GBIC: 2 x Mini-GBIC sockets

Console port: RJ-45 type

Network Cable 10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable

EIA/TIA-568 100-ohm (100m)

100Base-TX: 2-pair UTP/STP Cat. 5/5E cable

EIA/TIA-568 100-ohm (100m)

Optical Cable Multi-mode: 50/125um~62.5/125um

Single-mode: 9/125um

Protocol CSMA/CD

The 8 10/100TX + 12 100FX + 2 Gigabit Mini-GBIC Managed Industrial Switch is

a cost-effective solution and meets the high reliability requirements demanded

by industrial applications. The 8 10/100TX + 12 100FX + 2 Gigabit Mini-GBIC

Managed Industrial Switch can be easily managed through the Web GUI. Using

fiber port can extend the connection distance that increases the network

elasticity and performance. It provides the X-Ring function that can prevent the

network connection failure, and meets the standard of IEC-61850-3 and IEEE-

1613 for the substation environment applications.

LED Front Panel

Per unit: Power 1 (Green), Power 2 (Green), P-Fail (Red),

R.Master (Green)

Port1~22 : Link/Activity (Green), Port13~20: 100M (Green)

Rear Panel

Per unit: Power 1 (Green), Power 2 (Green), P-Fail (Red),

R.Master (Green)

Port1~22 : Link/Activity (Green), Port13~20: Full-duplex

(Amber)

Reverse Polarity

Protection Present

Overload Current

Protection Present

Power Supply AC/DC

Power

Consumption 27.6 Watts max. @ 110 VDC

26.2 Watts max. @ 110 VAC

Operating Humidity 5% to 95% (Non-condensing)

Operating

Temperature Wide Operating Temperature (-40℃~85℃)

Storage

Temperature -40 to 85℃℃

Case Dimensions Metal case. IP-30, 440mm (W) x 44mm (H) x 280mm (D)

Installation DIN-rail and Wall-mount Design

1.2 Software Features

Management SNMP v1 v2c, v3 / Web / Telnet / CLI

SNMP MIB RFC 1215 Trap, RFC1213 MIBII, RFC 1157 SNMP MIB,

RFC 1493 Bridge MIB, RFC 2674 VLAN MIB, RFC 1643 ,

RFC 1757, RSTP MIB, LLDP MIB, Private MIB

VLAN Port Based VLAN

IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K,

VLAN ID can be assigned from 1 to 4094.)

GVRP (256 Groups)

Port Trunk with

LACP LACP Port Trunk: 13 Trunk groups/Maximum 4 trunk

members

LLDP Support LLDP to allow switch to advise its identification and

capability on the LAN

IES-22812F-2P: 100~240V

IES-22812F-2P:

Spanning Tree Support IEEE802.1w Rapid Spanning Tree

Pro-Ring Support X-Ring, Dual Homing, Couple Ring Topology.

Provide redundant backup feature and the recovery time

below 10ms.

Quality of Service The quality of service determined by port, Tag and IPv4

Type of service, IPv4 Different Service

Class of Service Support IEEE802.1p class of service, per port provides 4

priority queues

Port Security Support 50 entries of MAC address for static MAC and

another 50 for MAC filter

Port Mirror Support 3 mirroring types: “RX, TX and Both packet”.

IGMP Support IGMP snooping v1,v2

256 multicast groups and IGMP query

IP Security Support 10 IP addresses that have permission to access the

switch management and to prevent unauthorized intruder.

Bandwidth Control Support ingress packet filter and egress packet limit

The egress rate control supports all of packet type and the

limit rates are 0~100Mbps for Port1~20 and 0~1000Mbps for

Port21/22.

Flow Control Support Flow Control for Full-duplex and Back Pressure for

Half-duplex

System Log Support System log record and remote system log server

SMTP Support SMTP Server and 6 e-mail accounts for receiving

event alert

Relay Alarm Provides one relay output for port breakdown & power failure

Alarm Relay current carrying ability: 1A @ DC24V

SNMP Trap Up to 3 Trap stations

Cold start, Warm start, Port link up, Port link down,

Authentication Failure, Port fault relay alarm, X-Ring

topology change

DHCP Provide DHCP Client/ DHCP Server functions

DNS Provide DNS client feature and support Primary and

Secondary DNS server

SNTP Support SNTP to synchronize system clock in Internet

Firmware Update Support TFTP firmware update, TFTP backup and restore.

Configuration

Upload and Support binary configuration file for system quick installation

Inhaltsverzeichnis

Andere Lantech Schalten Handbücher

Lantech

Lantech IES-5416DF Series Bedienungsanleitung

Lantech

Lantech IPGS-0204DSFP-12V Bedienungsanleitung

Lantech

Lantech IES-0008B Series Bedienungsanleitung

Lantech

Lantech IPWMR-3204DF Bedienungsanleitung

Lantech

Lantech IPES-0005B Series Bedienungsanleitung

Lantech

Lantech IES-5416T Series Bedienungsanleitung

Lantech

Lantech IGS-L5408MGSFPR-AC Bedienungsanleitung

Lantech

Lantech IPES-5222T Series Bedienungsanleitung

Lantech

Lantech IPWMR-3006 Bedienungsanleitung

Lantech

Lantech IPGS-0005T-4-12V Bedienungsanleitung

Lantech

Lantech mini Switch 800 Bedienungsanleitung

Lantech

Lantech TPGS-L6208XT Bedienungsanleitung

Lantech

Lantech IES-3 Series Bedienungsanleitung

Lantech

Lantech IGS-0008A Bedienungsanleitung

Lantech

Lantech IES-2008B-DNV Bedienungsanleitung

Lantech

Lantech IES-2208CA Bedienungsanleitung

Lantech

Lantech IPGS-5008T Series Bedienungsanleitung

Lantech

Lantech LPES-2224C Bedienungsanleitung

Lantech

Lantech IGS-2404 Bedienungsanleitung

Lantech

Lantech IPES-0008B Series Bedienungsanleitung

Lantech

Lantech IPGS-0204DSFP Bedienungsanleitung

Lantech

Lantech LPES-2208CA Bedienungsanleitung

Lantech

Lantech IPES-2208CA Bedienungsanleitung

Lantech

Lantech IPES-0008A Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung