Lantronix DSTni-XPress DR Bedienungsanleitung

900-289 Rev B

DSTni-XPress DR Quick Start

DSTni-XPress DR/DR-IAP

DSTni-XPress DR and DSTni-XPress DR-IAP are

members of the Lantronix family of Device Servers.

DSTni-XPress DR-IAP devices allow you to install the

protocol suitable for your automation application.

When you complete the setup, you can Ethernet-enable a

serial device by connecting it to the serial port. (See the

DSTni-XPress DR User Guide on the software CD.)

Quick Connect

Screw Terminals for

RS-232 and RS-485/422

RJ45 Serial Port

RS-232 & RS-422/485

RS-232 or RS-485/422

Select Switch

Screw Terminals for

9-30VDC or 9-24VAC

RJ45 10/100BASE-T

Ethernet Port

Status LEDs

Reset Switch

Transmit Active LED

& Receive Active LED

RESET

10/100BASE-T SERIAL

RS232

RS485

Ethernet

Serial

1. Connect the XPress DR to the network through the

Ethernet port. (The unit must be on the same network

as your computer.)

2. Connect power (9-30VDC or 9-24VAC).

19 20

21 22

GND

9-30VDC

DC+

DC-

9-24VAC

3. Verify that the green Link LED is lit.

Setup

Follow these steps to quickly setup the device.

Step 1: Start DeviceInstaller

1. Insert the software CD into your CD-ROM drive.

When the main window appears, click the Device

Installer button and follow the instructions on the

screen.

2. Click the Start button, and then point to Programs.

Point to the folder that contains Device Installer, then

click Device Installer. The Device Installer main

window will appear.

Step 2: Assign an IP Address

1. Click the Assign IP icon. The Assign IP

Address window displays.

2. In the Enter the Hardware or Ethernet Address

field, type the Ethernet address (MAC address) listed

on the Device Server label (on the right side of the

unit).

3. In the Enter IP Address to assign field, type the IP

address of the Device Server (xxx.xxx.xxx.xxx

format). Select a PC Network Class.

4. Click the Set IP Address button. The Assign IP

Successful message displays. Click OK.

Step 3: Search the Network

1. Click the Search Network icon . The Search

Network window displays.

2. Click the Start Search button. The message Response

from xxx.xxx.xxx.xxx appears in the window. Click the

Save button and a device saved message appears. Click

OK then the Back button. The IP Address and

Hardware Address appear in the window.

Step 4: Pinging Devices

1. From the main DeviceInstaller window, select the

installed device from the list, then click the Ping

Device icon . A reply from the selected device

indicates an active device. An error message indicates

a problem with the network. See the user manual for

troubleshooting network problems.

2. From the Ping Device window, you can ping devices

not listed in the main window by entering a new

address in the IP address field.

DSTni-XPress DR-IAP devices allow you to install a

protocol such as MODBUS Bridge for your automation

application. Skip Step 5 if you have a DSTni-XPress DR..

Step 5: Upgrade the Firmware

1. Click the Upgrade Firmware icon . The

Upgrade Firmware window displays. The IP address

displays in the first field.

2. Select the current protocol using the list button in the

Existing Firmware field. (factory default = IAP

Standard Tunnel)

3. Click the open file icon next to the FW File field. A

list of firmware files displays. Use the search buttons

to locate the firmware files on the CD or downloaded

files from the Lantronix support web page.

4. Select the desired protocol and click Open. The

selected file and path displays in the FW File field.

5. Click Upgrade FW File. The File upgrade successful

message displays. Click OK and close the upgrade

firmware window.

Step 6: Configure the Device

To view or update the Device Server configuration, use the

Device Management window to open a Telnet connection.

1. Click the Device Management icon . Click the

Telnet to Device icon.

2. When the Telnet window opens, you have 5 seconds to

press the Enter key.

3. Note the firmware code and description on the first few

lines.

4. Review and edit the settings to match your application.

When done, enter S to save the changes and Q to Quit.

Step 7: Connecting Serial Devices

The cable below is a typical PC (COM1) to DSTni-XPress

DR cable using the serial RJ-45 connector. You can use the

serial port to configure and test the port settings prior to

connection to your automation device.

DTR (Out)

RXD (In)

TXD (Out)

Signal Ground

CTS (In)

RTS (Out)

DSR (In)

SERIAL RJ-45DTE, 9-Pin, FEMALE

No Connection

DTR (Out)

RXD (In)

TXD (Out)

Signal Ground

CTS (In)

RTS (Out)

No Connection

CTS

RTS

DTR

DSR

GND

TXD

RXD

SERIAL RJ-45DTE, 9-Pin, FEMALE

View from

Connector End

The following cable connects a typical PC (COM1) to the

DSTni-XPress DR through the serial screw terminals.

CTS

RTS

DTR

DSR

GND

TXD

RXD

RXD TXD

GND

DTE, 9-PIN, FEMALE DTE, 9-PIN, FEMALE

Dieses Handbuch passt für folgende Modelle

Andere Lantronix Server Handbücher

Lantronix

Lantronix EDS-MD EDS-MD4 Installationshandbuch

Lantronix

Lantronix xPico XPW100A003-01-B Kurzanleitung zur Einrichtung

Lantronix

Lantronix EDS32PR Bedienungsanleitung

Lantronix

Lantronix PremierWave XN Bedienungsanleitung

Lantronix

Lantronix WiPort Bedienungsanleitung

Lantronix

Lantronix WiPort NR Bedienungsanleitung

Lantronix

Lantronix SCS1600 Bedienungsanleitung

Lantronix

Lantronix xport pro Kurzanleitung zur Einrichtung

Lantronix

Lantronix XPort Bedienungsanleitung

Lantronix

Lantronix EDS32PR Bedienungsanleitung

Lantronix

Lantronix XPort Bedienungsanleitung

Lantronix

Lantronix xPico Bedienungsanleitung

Lantronix

Lantronix Console Server 3200 Bedienungsanleitung

Lantronix

Lantronix Device Server MSS 485 Bedienungsanleitung

Lantronix

Lantronix EDS3000PR Bedienungsanleitung

Lantronix

Lantronix EDS32PR Bedienungsanleitung

Lantronix

Lantronix xDirect Bedienungsanleitung

Lantronix

Lantronix xSenso 2100 Bedienungsanleitung

Lantronix

Lantronix UDS1100 Bedienungsanleitung

Lantronix

Lantronix xport pro Installationshandbuch

Lantronix

Lantronix XPress DR Bedienungsanleitung

Lantronix

Lantronix MSS4 Bedienungsanleitung

Lantronix

Lantronix SCS Bedienungsanleitung

Lantronix

Lantronix MSS4-D Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung