Larson Electronics EPLC2-LED-400W Bedienungsanleitung

EPLC2-LED-400W

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 3

Explosion Proof LED Light Light Fixture

Instruction Manual

Do not attempt installation until you are familiar with all warnings, precautions, and procedures outlined within

this instruction sheet.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE

REFERENCE. CRITICAL SAFETY INSTRUCTIONS:

•To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and

maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

•Be certain electrical power is OFF before and during installation and maintenance.

•Luminaire must be supplied by a wiring system with an equipment grounding conductor.

To avoid burning hands:

•Make sure lens and housing are cool when performing maintenance.

To avoid explosion:

•Make sure the supply voltage is the same as the luminaire voltage.

•Do not install where the marked operating temperatures exceed the ignition temperature of the

hazardous atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

•Use proper supply wiring as specified on the luminaire nameplate.

•All gasket seals must be clean.

•Before opening, electrical power to the luminaire must be turned off. Keep tightly closed when in

operation.

Refer to the luminaire nameplate for specific classification information, maximum ambient temperature

suitability, and corresponding operating temperature (TCode).

Luminaire construction is designed for use indoors and outdoors in marine and wet locations, where moisture,

dirt, corrosion, vibration, and rough usage may be present.

MOUNTING

1. Mount the cover module in its support position.

2. Ceiling and wall mount: mark and drill desired location on

mounting surface. Secure with 1/4" (6mm) bolts or lag

screws (not provided).

3. Pendant, stanchion mount: securely thread onto the

appropriate NPT size conduit. Tighten set-screw located in

the conduit hub. See Figure 1.

4. Thread lubricant must be added to the conduit threads to

prevent water from entering the fixture.

WIRING (Voltage: 120-277VAC 50/60 Hz)

1. Pull field wiring into cover module.

2. Close all unused conduit entries with conduit plugs provided. To prevent galling and to ensure water-

tightness, lubricate conduit plugs with lubricant before installing, and secure wrench-tight with at least

five (5) full threads engaged (42-52 ft.-lb. for 3/4” plugs, and 58-68 ft.-lb. for 1” plugs).

3. Hang LED luminaire on the cover module hinge hook. See Figure 2a.

EPLC2-LED-400W

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 3

4. Connect supply wires to luminaire wire leads (or terminal blocks) per the

attached wiring diagrams using methods that comply with all applicable

codes. See Figure 2b. Tighten all electrical connections.

5. Close driver housing onto cover module, making sure that all wires are

safely inside driver. Tighten captive closing screw to 30 in.-lbs. (3.4 N-m).

Ensure two (2) bosses on driver housing are in contact with cover module.

6. Turn power on.

MAINTENANCE

1. Perform visual, electrical, and mechanical inspections on a regular basis. The environment and

frequency of use should determine this. However, it is recommended that checks be made at least

once a year. We recommend an Electrical Preventive Maintenance Program as described in the

National Fire

2. Protection Association Bulletin NFPA No. 70B: Recommended Practice For Electrical Equipment

Maintenance (www.nfpa.org).

3. The lens should be cleaned periodically to ensure continued lighting performance. To clean, wipe the

lens with a clean, damp cloth. If this is not sufficient, use a mild soap or a liquid cleaner such as

Collinite NCF or Duco #7. Do not use an abrasive, strong alkaline, or acid cleaner. Damage may result.

4. Visually check for undue heating evidenced by discoloration of wires or other components, damaged

parts, or leakage evidenced by water or corrosion in the interior. Replace all worn, damaged, or

malfunctioning components, and clean gasket seals before putting the luminaire back into service.

5. Electrically check to make sure that all connections are clean and tight.

6. Mechanically check that all parts are properly assembled.

REPLACEMENT PARTS

The EPLC2-LED-150W is designed to provide years of reliable lighting performance. Should the need for

replacement parts arise, please contact Larson Electronics at the contact information below.

Should further information not covered by these instructions be required, please contact Larson Electronics at

1-800-369-6671 or [email protected] for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

EPLC2-LED-400W

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

3of 3

INSTALLATION CHECKLIST

Verify sufficient lubricant is on conduit plugs

(recommend approximately 1/8” bead

around the first thread of plug) and that all

unused conduit entries on the cover module

are closed with lubricated plugs.

Verify conduit plugs are installed to at least

five (5) full threads into the cover module

conduit entries.

Verify installed conduit plugs are torqued to

42-52 ft.-lbs. for 3/4” plugs and 58-68 ft.-lbs.

for 1” plug.

Verify supply wires are connected to

luminaire wire leads (or terminal block) per

wiring diagrams.

Verify all electrical connections are

tightened.

Verify all wires are safely and neatly inside

driver housing and not on top of wire

terminal. Close driver housing onto cover

module.

Verify captive closing screw is tightened to

30 in.-lbs. (3.4N-m) and two (2) bosses on

driver housing are in contact with cover

module.

Inhaltsverzeichnis

Andere Larson Electronics Leuchte Handbücher

Larson Electronics

Larson Electronics SPLT-1.59K-800A-30-4X100W-LED-MS Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-24-50LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-1X30LED-120XLV-100 Handbuch

Larson Electronics

Larson Electronics CL1B-SS-PM-1227 Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-45LED-RT-WLM Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-MBC-1MLED-2023 Handbuch

Larson Electronics

Larson Electronics EPL-16BS-1X150LED-X24I-C1D1-200 Handbuch

Larson Electronics

Larson Electronics RCL360-LED-40 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-EMG-HB-50LED-RT-WLM Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-AMB-70LED-50 Handbuch

Larson Electronics

Larson Electronics HALD-24-1X150LED-V3-DIMM Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-G3 Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-40LED-RT-CM Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-1X30LED-100 Handbuch

Larson Electronics

Larson Electronics EPL-QP-1X150-100 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-3 Series Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-WP-500LTL-LED-WG-DNMS Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-50LED-RT-SP0122 Bedienungsanleitung

Larson Electronics

Larson Electronics HALS-48-2L-LED Bedienungsanleitung

Larson Electronics

Larson Electronics IND-AHF-BX-UVC-R2-120V-15C Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-5K-LED Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-C-4XM Bedienungsanleitung

Larson Electronics

Larson Electronics LED T Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-3X150LED-RT Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung