Larson Electronics HALP-96-2L-LED Bedienungsanleitung

HALP-96-2L-LED

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 1

Hazardous Location Corrosion Resistant LED Light Fixture

Instruction Manual

Thank you for your purchase of the Larson Electronics HALP-96-2L-LED Corrosion Resistant light fixture.

Please follow the steps below in order to operate and maintain this product.

FIXTURE ASSEMBLY

Fixtures are shipped separately for shipping purposes and must be re-assembled for operation.

1. Remove fixtures from their packaging.

2. Place fixtures side by side with the wire side of one facing the open end of the opposite light fixture. There

will only be one fixture with excess wiring tucked into it and one fixture with an open end.

3. Un-tuck wiring from first fixture along with lock nut and insert wiring into the other light fixture.

4. Open the second fixture (with open end) to access its internals. See page 2 steps 3 thru 5 to open and

release the lamp tray from the light fixture.

5. Once open, place the first fixture’s threaded conduit through the open end of the second fixture.

6. Slide the lock nut through the wiring before connecting to wire terminal.

7. Tighten lock nut down over conduit to secure the fixtures together.

8. Connect the wires from the first light fixture to the wiring terminal. Match the colors to the wires already

there. White to white, black to black.

9. Once the wiring has been connected, close the lamp and proceed to mounting.

FIXTURE 1

FIXTURE 2

HALP-96-2L-LED

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 1

Hazardous Location Corrosion Resistant LED Light Fixture

Instruction Manual

Thank you for your purchase of the Larson Electronics HALP-96-2L-LED Corrosion Resistant light fixture.

Please follow the steps below in order to operate and maintain this product.

WARNING!

1. TO PREVENT RISK OF ELECTRICAL SHOCK DEACTIVATE/DISCONNECT POWER SUPPLY BEFORE

INSTALLING, MAINTAINING OR RELAMPING FIXTURE.

2. TO REDUCE RISK OF FIRE OR EXPLOSION, DO NOT INSTALL WHERE THE MARKED OPERATING

TEMPERATURE EXCEEDS THE IGNITION TEMPERATURE OF THE HAZARDOUS ATMOSPHERE(S).

3. THIS FIXTURE SHOULD BE INSTALLED BY QUALIFIED TECHNICIANS IN STRICT ACCORDANCE WITH THE

NATIONAL ELECTRICAL CODE AND ANY LOCAL REQUIREMENTS.

INSTALLATION

1. Connect fixtures together as shown on first page.

2. Install fixture to surface with four mounting brackets on each side (mounting hardware not included).

3. Remove lens by releasing plastic latches that secure it.

4. Remove lamps.

5. Pinch latches on either side to release the lamp tray from the housing.

6. Electrical voltages and frequency are listed on the nameplate for reference.

7. For supply connections use conductors suitable for min. 90° C.

8. Connect internal wires per wiring diagram, and according to NEC requirements.

9. Replace the lamp tray and snap into latches to secure.

10. Install lamps.

11. Replace lens and secure all latches.

MAINTENANCE

Electrical and mechanical inspection of all components must be performed on a regularly scheduled basic, determined by

the environment and frequency of use. It is recommended that inspection be performed a minimum of once a year.

WARNING: ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND

MAINTENANCE. INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND

COMPETENT ELECTRICIAN.

1. Inspect all contact wire terminals for tightness. Discoloration due to excessive heat is an indicator of a possible

problem and should be thoroughly investigated and repaired as necessary.

2. Inspect contacts for signs of wear and replace if necessary.

3. Clean exterior surfaces making sure nameplates remain legible.

If any part of the light appears to be missing, broken, or show signs of damage—discontinue use immediately! This

condition could cause serious or fatal personal injury due to electrocution and/or equipment damage. Repair with the

proper replacement part(s) before continuing service.

TROUBLESHOOTING

Refer to the guide below or contact the manufacturer if the fixture does not function properly.

Is the correct line voltage being supplied to the fixture?

Is the fixture properly grounded?

These instructions may not cover all details or variations of this product for your equipment or installation requirements. Should further

information not covered by these instructions be required, please contact Larson Electronics at 1-800-369-6671 for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

Inhaltsverzeichnis

Andere Larson Electronics Leuchte Handbücher

Larson Electronics

Larson Electronics EPL-HB-3X150LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-25LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics GL-3 Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-100LED-RT-JB2-6-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-SBDL-SS-WP60E-24-1227 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-EMG-HB-50LED-RT-WLM Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-150LED-PND Bedienungsanleitung

Larson Electronics

Larson Electronics HALS-48-2L-LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-16BS-1X150LED-X24I-C1D1-200 Handbuch

Larson Electronics

Larson Electronics GAU-WP-500LTL-LED-WG-DNMS Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-D-LV Bedienungsanleitung

Larson Electronics

Larson Electronics IND-HR-UVC-EXS-R1-24-3L-120V-2X Bedienungsanleitung

Larson Electronics

Larson Electronics Golight Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-PT-LED-CPR-C-100 Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-24-50LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PT-150LED-RT-100-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-PRM-150W-LED-100 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT-DIMM Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-BS-70LED-100 Handbuch

Larson Electronics

Larson Electronics EPL-LP-70W-LED-WALL Handbuch

Larson Electronics

Larson Electronics IND-AHC-CR-12-UVC-R1-120V Bedienungsanleitung

Larson Electronics

Larson Electronics ATEX-EHL-1123-LED-50-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-1X30LED-120XLV-100 Handbuch

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung