Larson Electronics EPS-2XPB-SG-600V-LKC Bedienungsanleitung
EPS-2XPB-SG-600V-LKC
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com
1of 3
Explosion Proof Push Button 600V Stop/Start Switch
Class I, II, III - Motor Starter Switch - (2) Lockout
Instruction Manual
Thank you for your purchase of the Larson Electronics EPS-2XPB-SG-600V-LKC.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE EPS-2XPB-SG-600V-LKC MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The EPS-2XPB-SG-600V-LKC from Larson Electronics is a 600V Explosion Proof Push Button Stop/Start Switch that is
Class I, Divisions 1 & 2 and Class II, Divisions 1 & 2 rated for hazardous locations. This explosion proof switch provides
manual starting and stopping of small AC and DC motors. Operators may access two stainless steel lockouts for the push
buttons.
EPS-2XPB-SG-600V-LKC
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com
2of 3
INSTALLATION
1. Mount the back box by means of mounting lugs. Install conduit nipple and sealing fittings, to be installed on each
conduit entrance or exit to the enclosure back box in Class I and Class II areas. Thread conduit into sealing fitting
(Note: For Class I areas, the conduit should engage [5] full threads.)
2. The conduit threads should be lubricated with a non-electrical insulating lubricant or pipe joint compound that will
not promote corrosion or chemically attack aluminum.
3. After conduit system has been properly installed, pull the wires and make electrical connections as required. The
electrical circuits and ground continuity should be checked with an instrument approved for the area. Notice:
Connect only copper wire to this device.
4. All conduits entering or leaving the enclosure must be sealed within 18” of the enclosure with listed sealing
fittings. Caution must be taken during installation to be sure that the ground flange flame joints of the cover and
box are not scratched, nicked, or damaged. Before assembly of the cover to the box, the mating ground surfaces
of both the box and cover should be wiped clean to assure that the ground flame joint will be free of all foreign
particles such as lint, dust or dirt.
5. After tightly bolting the cover assembly/assemblies to the enclosure, all box to cover flame joints should be
checked with a 0.0015” thick feeler gauge such that the gauge will not enter the flame path more than 1/8” at any
point.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 600V.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
MAINTENANCE
All moving shafts should be lubricated
occasionally to prevent binding. Only use a
lubricant which is suitable for use with
aluminum or stainless steel. If devices are
to be installed in corrosive areas which will
attack aluminum alloys containing less than
0.4% copper (boxes and covers) and 303
stainless steel (mostly shafts), the device
should be suitably protected from the
corrosive material.
CAUTION: To prevent ignition of
hazardous atmospheres, disconnect from
the supply circuits before opening the
enclosure; keep tightly closed while circuits
are energized.
EPS-2XPB-SG-600V-LKC
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com
3of 3
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPS-2XPB-SG-600V-LKC is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Inhaltsverzeichnis
Andere Larson Electronics Schalten Handbücher
Larson Electronics
Larson Electronics EPS-2XPB-SG-DPMS Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-25A-3W Bedienungsanleitung
Larson Electronics
Larson Electronics EPSW-1PH-20 Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-DCSW-50A-600V Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-25A Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-3PSW-MMS Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-PB10-MS-SPDT Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-10HP-3PST Bedienungsanleitung
Larson Electronics
Larson Electronics GAU-SW-4P-WW-24V Bedienungsanleitung
Larson Electronics
Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1 Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-PB10-MS-AT-V4 Bedienungsanleitung
Larson Electronics
Larson Electronics EPCS-PL-2X-RG Bedienungsanleitung
Larson Electronics
Larson Electronics EXP-EL-CSS-250A-R1-NO Bedienungsanleitung
Larson Electronics
Larson Electronics EPNFDS-MTS-200A-3P Bedienungsanleitung
Larson Electronics
Larson Electronics C1D2 Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-SW1-ESTP Bedienungsanleitung
Larson Electronics
Larson Electronics EXHL-TRN-LE1 Series Bedienungsanleitung
Larson Electronics
Larson Electronics EPL-SW Series Bedienungsanleitung
Larson Electronics
Larson Electronics EPSW-30A-WP Bedienungsanleitung
Larson Electronics
Larson Electronics EPS-PB10-2XC-M2-YR Bedienungsanleitung
