LARSON SmoothGlide Bedienungsanleitung

202220648 Rev 082510 color

SmoothGlideTM Closer Installation Instructions

#10x5/8”SCREW#10x11/2”SCREW

LONGPINSHORTPIN

Not your ordinary closer, SmoothGlideTM (Patents Pending) provides a smooth and uniform closing motion from start to finish.

Your door is equipped with two closers:

x A SmoothGlideTM closer installed at the top of the door

x A SmoothGlideTM closer with Touch’n Hold at the bottom of the door

1) Preparation

Locate the closer screw pack, which contains:

x 8 - #10 x 1-1/2” screws

x 4 - #10 x 5/8” screws

x 2 - short pins

Tools required:

x Power drill with an 1/8” drill bit

x No.2 Phillips screwdriver

2) Install the jamb brackets:

a) TOP CLOSER; Locate jamb bracket about 1“ down from the top of the

door with the positioning tab against the back leg of the hinge rail. Drill 1/8”

pilot holes and fasten bracket to jamb with four #10 x 1-1/2” screws, per

Fig.2.

b) BOTTOM CLOSER; Locate jamb bracket about 1“ above the door expander with

the positioning tab up against the back leg of the hinge rail. Note: Bottom closer

may need to be located over the door expander in some cases. Drill 1/8” pilot holes

and fasten bracket to jamb with four #10 x 1-1/2” screws, per Fig.3.

After fastening the jamb brackets, break off the positioning tabs.

3) Install the door brackets

a) TOP CLOSER; Close and latch the door. Assemble

the closer (the closer without the Touch’n Hold button; it

has the door bracket already attached to it) to the top

jamb bracket using the short pin and long yellow

plastic spacer clip, per Fig.4. (NOTE: Long yellow

plastic spacer clip must be used to ensure proper

operation and function). Hold the assembly level and

mark the front mounting hole location of the door

bracket. Drill 1/8” starter hole. Caution: Do not drill

through the outside of the door. Attach the door

bracket using a #10 x 5/8” screw. Remove the long pin,

short pin, closer and yellow plastic clip. Discard the

yellow clip. Drill 1/8” starter hole through exposed hole

in door bracket and fasten using #10 x 5/8” screw. Reattach the closer using the long pin, with o-ring to hold in place, and short pin.

Fig. 1 Full Scale

Fig. 2

Fig. 3

Fig. 4

LongYellowClip

Jamb Bracket

ShortYellow

Clip

b) BOTTOM CLOSER;

Close and latch the

door. Assemble the

bottom closer (the

closer with the Touch’n

Hold button), door bracket and long pin

together with the arrow on the door bracket,

per Fig.5, pointing toward the hinge side of the

door. Attach to the bottom jamb bracket using

the short pin and short yellow plastic spacer

clip, per Fig.6. (NOTE: Short yellow plastic

spacer clip must be used to ensure proper

operation and function). Hold the assembly

level and mark the front mounting hole location

of the door bracket. Drill 1/8” starter hole.

Caution: Do not drill through the outside of the door. Attach the door bracket using a #10 x 5/8” screw. Remove the long pin, short

pin, closer and yellow plastic clip. Discard the yellow clip. Drill 1/8” starter hole through the exposed hole in the door bracket and fasten

using #10 x 5/8” screw. Reattach the closer using the long pin, with o-ring to hold in place, and short pin.

Note: If you need to adjust the horizontal positioning do not drill additional holes.

There are four additional adjusting positions. This will affect the closing force as the door closes through the last 12 inches of operation.

This can be done by reversing the arrow direction on the door brackets and changing the hole that is used on the closer.

More Closing Force:

Arrow on door bracket is

pointed away from the

hinge side of door and

closer is attached to door

bracket using the front

hole.

Standard Installation:

Arrow on door bracket is

pointed toward the hinge

side of door and closer is

attached to door bracket

using the front hole.

Less Closing Force:

Arrow on door bracket is

pointed away from the

hinge side of door and

closer is attached to

door bracket using the

rear hole.

Least Amount of

Closing Force:

Arrow on door bracket is

pointed toward the hinge

side of door and closer is

attached to door bracket

using the rear hole.



Operation and adjusting instructions:

 To hold the door open: Just press the Touch’n Hold button on the closer.

 To close: Push the door open slightly and release.

To adjust closing speed:

 The door closers are adjusted at the factory for the comfort zone, to close the door in 4-5 seconds.

 This setting may be adjusted from the thumbscrew shown in Fig. 7. Caution: Do not use a power

tool to install or adjust the screw.

 It is recommended to adjust closers individually (with the other closer disconnected). Turn

clockwise to turn down the speed of the door.

Slower

Faster

Arrow

Fig. 7

Fig. 5

Fig. 6

Touch’nHoldButton

BottomofDoor

ShortYellowClip

Andere LARSON Türöffnungssystem Handbücher

LARSON

LARSON SCREEN-AWAY Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Label

Label NEPTIS/LE Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Olide

Olide 120B Bedienungsanleitung

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung