Laser 4599 Bedienungsanleitung
www.lasertools.co.uk
Part No. 4599
Digital Torque Adaptor
1/2"D
Instructions
This Torque adaptor can be used with any 1/2"D power bar or ratchet. The tool
enables the correct torque to be set on any fastener, ranging from 40-200Nm.
Calibration mode
The Adaptor will enter into Calibration mode if Mem and are pressed
simultaneously.
Battery Installation – 2 x AAA Batteries
• Low battery will show icon.
• Unscrew the retaining screws in the battery cap.
• Remove the old batteries.
• Screw the cap back into place.
Power
• Press and release the button to turn the adaptor on.
• The LCD panel will show trACE or PtoP.
• After 2 secs the LCD panel will show 0.0.
• The LCD will be displayed for 70 seconds before it will go off automatically.
Peak
• This will show the reading as the torque increases, and then hold at the highest
reading.
• With the power On, press and release the Peak-Trace button.
• When PtoP appears – release the button.
• Each time Peak is used the reading is stored up to 50 readings with the torque
setting.
• Each reading will be automatically numbered P50-01 (P01 will be the latest
number P50 the oldest).
Trace
• This will follow the torque as it is applied.
• With the power On, press and release the Peak-Trace button.
• When TRACE appears release the button.
2
www.lasertools.co.uk
Instructions
Torque Setting
• Select M and Trace button together to select the required measurement.
• A pointer on the top of the LCD display indicates the torque setting.
• Torque settings include:
Kg-cm 408 - 2040
Kg-m 4.08 - 20.4
In-lb 354 - 1770
Ft-lb 29.5 - 148
N-m 40 - 200
How to Increase or Decrease Torque Value
• Using the + or – buttons the target torque can be reset.
• The target Torque value will show for 10 seconds before resetting to 0.0.
How to apply Torque
1. Turn On the adaptor.
2. Select the required Torque Setting (Nm etc).
3. Select Peak or Trace.
4. Attach to a standard power bar or ratchet and apply the torque gradually
5. When you are approaching 80% of the target you will see a red light flash and
hear an intermittent buzzer warning.
6. Once you reach the required torque the red light will illuminate and the buzzer will sound.
(It is important not to apply torque too fast as this buzzer and light may be missed)
Memory
• Each time Peak is used the reading is stored up to 50 readings.
• Each reading will be automatically numbered P01-P50.
• (P01 will be the latest number P50 the oldest).
Turn Off
• The torque adaptor will automatically shut off if unused for 70 seconds.
• To turn off manually press and release the button.
3
www.lasertools.co.uk
Instructions
Our products are designed to be used correctly and with care for the purpose for which they
are intended. No liability is accepted by the Tool Connection for incorrect use of any of our
products, and the Tool Connection cannot be held responsible for any damage to personnel,
property or equipment when using the tools. Incorrect use will also invalidate the warranty.
If applicable, the applications database and any instructional information provided has been
designed to offer general guidance for a particular tool’s use and while all attention is given
to the accuracy of the data no project should be attempted without referring first to the
manufacturer’s technical documentation (workshop or instruction manual) or the use of a
recognised authority such as Autodata.
It is our policy to continually improve our products and thus we reserve the right to alter
specifications and components without prior notice. It is the responsibility of the user to
ensure the suitability of the tools and information prior to their use.
• Store in a clean, dry place.
• Clean with a soft dry cloth.
• Never submerge in water.
• Do not exceed the permitted torque settings.
• Do not expose to extreme temperature, humidity or direct sunlight.
www.lasertools.co.uk
4599_Instructions_V7
Safety Warnings - please read
Inhaltsverzeichnis
Andere Laser Empfänger Handbücher
