Lathem 700E Bedienungsanleitung

Document Number: USG0115 - Revised: 04/15/2017

Lathem Time

200 Selig Drive SW

Atlanta, GA 30336

www.lathem.com

Tel. (404) 691-1064

NOTICE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

Lithium battery contains perchlorate material – special handling may apply.

Visit: http://www.dtsc.ca.gov/hazardouswaste/perchlorate for information about proper methods of disposal.

The information within this document has been carefully checked and is believed

to be entirely reliable. However, no responsibility is assumed for inaccuracies.

Lathem reserves the right to make changes to any products herein to improve

reliability, function, or design.

TABLE OF CONTENTS

- Display & Buttons

- Setting the Rounding

- Reset to All Clear

- Card Reassign

9. PRECAUTIONS

1. GETTING STARTED

- Packing Contents

- Features

- SETUP: AC Adapter

- SETUP: Remove/Attach the Cover

- Installing the Ribbon Cassette

- Mounting Unit on Wall

3. DAILY OPERATION

4. DEFAULT SETTINGS

2. SETUP

5. SETTING: Date and Time

- Setting the Display Hours

- Setting the Time

- Setting the Date

6. SETTING: Function

- Setting the Mode-Pay Period

- Setting the Pay Period Starting Date/Days

- Setting the Print Format/Language

- Setting the Max In (Calculating Mode)

- Setting the Max In (Non-Calculating Mode)

- Setting the Auto Break Deduction

- Setting the Daylight Saving Time

7. OTHERS

- Setting/Changing the Passcode

- Inputting the Passcode

- Reset for Initialization

- Card Reset

8. INFORMATION

- Error No. Causes and Actions

- Other Failures

- Environmental Conditions

- Specifications

Overview

1. GETTING STARTED

Packing Contents

User's manual Wall mount

hardware

Ribbon cassette

Cover

Display

Control buttons

Card slot

Wall-mounting

holes

AC adapter

It is important that you register your product with Lathem shortly after purchase

to activate your product’s warranty.

To register online visit: www.lathem.com/register

12345 6

SETTING

Button

RESET

Switch

DATE/TIME

Button

FUNCTION

Button Button Button

SET

Button

700E

T W T F S

UOUEHR A

PASSWORD

DAYLIGHT

SAVINGS

SET

TIME MODE MAXIN

DATE/TIME

SETTINGSTART/END

Press

AUTO

BREAK

DEDUCTION

FUNCTION

ROUNDING

Short:

Long(3sec.):

SettingMode

RibbonChange

ErrorCancellation

FORMAT

CARD

DELETE

CARD

REASSIGN

DATE

DISPLAY

HOURS

Daylight saving time indication Day of the week indication

Current date

AM/PM

indication

Current column indication Current time

AM PM

Display and Buttons

Features

Calculating Mode (SumTime™)

• Fully automatic time clock for up to 100 employees

• DualMode™ feature provides Calculating or Non-Calculating operation

• SumTime™ Calculating mode option calculates elapsed hours between

punches and total accumulated hours for pay period in exact minute or

rounded time format

• Supports weekly, bi-weekly, semi-monthly and monthly pay periods

• Employee identification using E17 bar coded time cards, provides automatic

top card feed, punch alignment and print activation for simple one-hand

operation

• SmartClock™ technology keeps time, date and settings during power

outages, and auto-adjusts for Daylight Saving Time and Leap Years

• Display and print 1-12 AM/PM or 24 Hour format

• Print time in regular minutes (00-59) or hundredths of an hour (.00-.98)

• Print the Month, Year, Day of Week and Date, Hours between Punches,

and Total Accumulated Hours for the pay period

• Unlimited punches per day, 64 total punches in the pay period

Non-Calculating Mode

• Print Date or Day of Week and Time

• Up to six (6) punches per day. Each row of the time card is one day

Date

Hours between punches

Up to 6 punches per day

Accumulated hours

for pay period

IN OUT

This clock requires the use of E17 Time Cards only.

E17 time cards are bar coded and support all pay periods.

Features

Calculating Mode (SumTime™)

• Fully automatic time clock for up to 100 employees

• DualMode™ feature provides Calculating or Non-Calculating operation

• SumTime™ Calculating mode option calculates elapsed hours between

punches and total accumulated hours for pay period in exact minute or

rounded time format

• Supports weekly, bi-weekly, semi-monthly and monthly pay periods

• Employee identification using E17 bar coded time cards, provides automatic

top card feed, punch alignment and print activation for simple one-hand

operation

• SmartClock™ technology keeps time, date and settings during power

outages, and auto-adjusts for Daylight Saving Time and Leap Years

• Display and print 1-12 AM/PM or 24 Hour format

• Print time in regular minutes (00-59) or hundredths of an hour (.00-.98)

• Print the Month, Year, Day of Week and Date, Hours between Punches,

and Total Accumulated Hours for the pay period

• Unlimited punches per day, 64 total punches in the pay period

Non-Calculating Mode

• Print Date or Day of Week and Time

• Up to six (6) punches per day. Each row of the time card is one day

Date

Hours between punches

Up to 6 punches per day

Accumulated hours

for pay period

IN OUT

This clock requires the use of E17 Time Cards only.

E17 time cards are bar coded and support all pay periods.

Cover

Projections

<1>

<2>

SETUP: AC adapter

1Put the bottom face of a time recorder

toward you. Connect a plug of AC

adapter into the time recorder, and run

the cord into the groove on the bottom.

Then, plug the AC adapter into AC

outlet.

SETUP: Remove/Attach the Cover

Remove the cover.

<1> Pull the top of the cover toward

you supporting the bottom side of the

cover.

<2>Pull it to front and upper

direction. Then, remove the cover.

Attach the cover.

Fit the right and left sides on the

bottom of the cover in projections of

the unit. Then, attach the cover in the

reverse order of <1> and <2> in step 2.

2. SETUP

Place the ribbon cassette inside the

time recorder as shown in the figure.

Push the ribbon cassette until it snaps

into the clasps on both sides. If it is

difficult to insert the ribbon cassette,

try it while turning the knob.

Knob

Tab

Clasps

(located on both sides)

Knob

Installing the Ribbon Cassette

Remove the cover, and press

[SETTING] button for three seconds.

Then, display will change as follows

and a ribbon cassette moves to the

replacement position.

Note: Ribbon cassette is not factory

installed.

When you replace an installed ribbon

cassette to a new one, pull up the ribbon

cassette just above with the tab.

Make sure the power is on before installing.

[SETTING]

button

Turn the knob of the new ribbon cassette

in the same direction as the arrow to

tighten the ribbon.

Note: Must not turn the knob in the

opposite direction. Improper handling

causes malfunction of a ribbon cassette.

Install the ribbon cassette so that the ribbon is between the print head and the ribbon

mask (see the figure on the left). Printing will not come out properly if the ribbon is

placed behind the ribbon mask (see the figure on the right).

When you finish changing the ribbon

cassette, press [SETTING] button for

three seconds to be back to normal

punching mode.

Turn the knob of the ribbon cassette in

the direction of the arrow to tighten

the ribbon.

Knob

Print head

Ribbon mask

Ribbon

Print head

Ribbon mask

Ribbon

GNORWTCERROC

6 7

Mounting Unit on Wall

The supplied screws are intended

* Wall mounting template is located on

the back cover of this guide.

for use on a thick wooden wall

or wooden column. Do not use

them on any other materials.

There is a danger that the unit

may come off if used on the

other materials.

Install wall mount screws (supplied)

into a wall 10 cm (3-15/16") apart. Be

sure to keep about 3 mm (1/8") of the

screw head out of the wall. Use

template on the bottom of the back

side of this manual if you prefer.

10cm (3-15/16")

3mm

(1/8")

Mount the wall mount fittings

as shown on the right.

Plug the unit into power, and

the unit is ready to use.

The unit can be mounted on a wall using the supplied mounting fittings.

Wall

Wall Mount Template*

Screws

Make sure the power is off before mounting.

Inhaltsverzeichnis

Andere Lathem Uhr Handbücher

Lathem

Lathem 1600E Bedienungsanleitung

Lathem

Lathem 6000E Bedienungsanleitung

Lathem

Lathem DWA-4000 Bedienungsanleitung

Lathem

Lathem 1200 Series Bedienungsanleitung

Lathem

Lathem 1000E Bedienungsanleitung

Lathem

Lathem 1000E Bedienungsanleitung

Lathem

Lathem DDC2 Series Bedienungsanleitung

Lathem

Lathem 1221 Bedienungsanleitung

Lathem

Lathem 900E Bedienungsanleitung

Lathem

Lathem TruAlign 800P Bedienungsanleitung

Lathem

Lathem 2000 - 4000 Series Bedienungsanleitung

Lathem

Lathem LTR4-512 Bedienungsanleitung

Lathem

Lathem LTR4-512 Bedienungsanleitung

Lathem

Lathem 100E Bedienungsanleitung

Lathem

Lathem 7500E Bedienungsanleitung

Lathem

Lathem LTR-512 Montageanleitung

Lathem

Lathem DWA-4000 Bedienungsanleitung

Lathem

Lathem PC700 Bedienungsanleitung

Lathem

Lathem 2121 Bedienungsanleitung

Lathem

Lathem DWA Series Betriebsanleitung

Lathem

Lathem Airtime AT-DDC4 Bedienungsanleitung

Lathem

Lathem 2000 Bedienungsanleitung

Lathem

Lathem 2121 Bedienungsanleitung

Lathem

Lathem 2000 Bedienungsanleitung

Beliebte Uhr Handbücher anderer Marken

Silicon Laboratories

Silicon Laboratories SI5324 Bedienungsanleitung

Heathkit

Heathkit GC-1005 Bedienungsanleitung

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Bedienungsanleitung

Andrew O'Malley

Andrew O'Malley DOTKLOK Bedienungsanleitung

ALGE-Timing

ALGE-Timing ASC3 Bedienungsanleitung

Bodet

Bodet Profil 960 Bedienungsanleitung

Nixie Clock

Nixie Clock Divergence Meter Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8256-AL Bedienungsanleitung

Mini Gadgets

Mini Gadgets MCPro Bedienungsanleitung

Casio

Casio TMR-200 Bedienungsanleitung

Progetti

Progetti ILTEMPOSTRINGE Handbuch

BVItech

BVItech BV-101 Bedienungsanleitung

Progetti

Progetti KALIMERO Handbuch

La Crosse Technology

La Crosse Technology WT-3141b Handbuch

La Crosse Technology

La Crosse Technology W86531 Bedienungsanleitung

Sharp

Sharp SPC900 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-50447 Bedienungsanleitung

Datexx

Datexx DF0063 Bedienungsanleitung