LCN Benchmark III 9130 Bedienungsanleitung

Installation Instructions 740158-00

Benchmark®III

Swing Operator

Models: 9130, 9140, & 9150

121 West Railroad Avenue

Princeton, IL 61356-0100

800-526-2400

FAX: 800-248-1460

www.lcn.ingersollrand.com

740158-00

(

)

2008 In

ersoll-Rand Com

Limited

Page 2 of 19

General 2

Replacement Parts and System Components 2

1. Pre-Installation Site and Product Check 4

2. Operator Installation 5

3. Wiring 9

4. Arm and Cover Installation 10

5. Operational Check 12

6. Operator Adjustment 15

7. Release for Service 17

8. BenchMark III Software 18

GENERAL

The Benchmark is an automatic electromechanical swinging door operator for use on hinged,

center pivoted and offset pivoted doors. When activated, the Benchmark drives the door to full

open position, then electrical power is turned off and the door is closed by spring force. The

activating circuit opens the door from any position in the closing swing. During a power failure,

the Benchmark acts as a manual door closer (Size 3). Door opening and closing cycles,

including opening speed, back check speed, hold open time delay, closing speed, and latch

position, are adjustable.

Part 27” Header Full Length Header

Single Full Length Header

Double

Premium Control

Box 9130-3462SC

9140-3462SC 9130-3462SC

9140-3462SC 9150-3462SC

Gear Box 9130-3454S

9140-3554S 9130-3454

9140-3454 9150-3454S

End Caps 9130-334 9140-334 9150-334

Part Pull Standard Push Extended

Reveal Push Finish

Arm Assembly 9130-3077T 9140-3077

9150-3077 9140-3077L

9150-3077L US28

DC13

CONTENTS

REPLACEMENT PARTS & SYSTEM COMPONENTS

Page 3 of 19

REPLACEMENT PARTS & SYSTEM COMPONENTS (CNTD)

Page 4 of 19

1.1 Check that the Product Model is correct for the required application.

1.2 Check that all parts listed on the Bill of Material are in the shipping container.

1.3 Check the architectural drawings and final approved shop drawings for the position

of frame and structural openings.

1.4 Check header and frame dimensions and required clearances.

1.5 Check Door Width: 26” minimum for 27” Push Operator

30” minimum for 27” Pull Operator

36” minimum for Full Length Push or Full Length Pull Operators

1.6 Check that Door Weight is 200 lbs. or less. For heavier door, consult factory.

1.7 Check that a 115 volt, single phase, 60 Hz, fused 15 amp, 3-wire power supply is available

at the side jamb with approximately 12” of wire available to connect to the Operator.

UL approved flexible conduit is recommended for the 115 volt power line.

The 115 volt power supply must be a dedicated circuit from the main circuit breaker panel

and must NOT be connected into any building lighting system that operates flourescent

lights.

1. PRE-INSTALLATION SITE & PRODUCT CHECK

Page 5 of 19

2.1 Remove Control Box from Operator Mounting Bracket, then remove Motor/Gearbox from

Bracket:

2.2 Prepare Header/Frame and Door: 27” Pull System..............................Page 6

Full Length Pull System..................Page 6

27” Push System............................Page 7

Full Length Push System ...............Page 7

Double Push System......................Page 8

Low Ceiling Application..................Page 8

2.3 Install Operator Mounting Bracket on Header/Frame.

For Full Length systems, also install Switch Bracket on Header/Frame.

2.4 Install Motor/Gearbox on Operator Mounting Bracket.

Then install Control Box on Bracket.

2.5 Proceed to Chapter 3: Wiring (Page 9).

2. OPERATOR INSTALLATION

Page 6 of 19

27” Pull System

Header/Frame and Door Preparation

Full Length Pull System

Header/Frame and Door Preparation

Center Operator Cover (with End Caps removed) over opening and mark a vertical line at each

end. Align ends of Operator Mounting Bracket and Switch Bracket with vertical lines and adjust

vertical position per diagram below. Mark and prepare mounting holes.

2. OPERATOR INSTALLATION (CNTD)

Page 7 of 19

27” Push System

Header/Frame and Door Preparation

Full Length Push System

Header/Frame and Door Preparation

Center Operator Cover (with End Caps removed) over opening and mark a vertical line at each

end. Align ends of Operator Mounting Bracket and Switch Bracket with vertical lines and adjust

vertical position per diagram below. Mark and prepare mounting holes.

2. OPERATOR INSTALLATION (CNTD)

Page 8 of 19

Double Push System

Header/Frame and Door Preparation

Center Operator Cover (with End Caps removed) over opening and mark a vertical line at each

end. Align ends of Operator Mounting Bracket and Switch Bracket with vertical lines and adjust

vertical position per diagram below. Mark and prepare mounting holes.

Low Ceiling Application (27” Push System Only)

Header/Frame and Door Preparation

2. OPERATOR INSTALLATION (CNTD)

Page 9 of 19

TION

3.1 Refer to the appropriate wiring diagram for the Control Box (Page 19) or the diagram

supplied for custom applications.

Connect the following cables:

•Ground Cable (Ground the Operator properly with the earth from main supply)

•Hall Effect Cable (Do not wrap the Hall Effect Cable around the Motor Power Cable)

•Motor Power Cable (Do not wrap the Motor Power Cable around the Hall Effect Cable)

•Control Box Power Cable

3.2 Connect Activate, Safety, Key Switch, and lock accessories, as needed.

Refer to the accessory instructions for any accessories used.

Do not connect any remote activating device to the door unless it is located within

line of sight of the door.

3.3 When wiring is complete, proceed to Chapter 4: Arm and Cover Installation (Page 10)

3. WIRING

CAUTION

• Make sure all wires are properly dressed and secured to prevent interference

• Route all wiring away from moving parts, sharp edges, and heat sources

• Use copper conductors only

• Do not modify the factory wiring or connect into existing electrical circuits or devices

Page 10 of 19

WARNING

Keep hands, clothing, wires, tools, etc., AWAY FROM Operator Motor

when the Operator Motor is turned on

4.1 Make sure the Operator Powers is turned Off.

4.2 Install a jumper across the control box Main Act and Main Act.

4.3 Turn the operator power switch to On.

The operator motor will activate and drive to the Full Open position.

4.4 Attach the arm to the operator spindle loosely with the 8mm socket head screw.

For push systems, ensure that the adjusting boss is inserted correctly.

4.5 Attach the arm to the door.

4.5.1 For push systems, attach the push arm shoe to the door:

4. ARM & COVER INSTALLATION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LCN Türöffnungssystem Handbücher

LCN

LCN 1450 Series Bedienungsanleitung

LCN

LCN 4020 Series Bedienungsanleitung

LCN

LCN 2210DPS Series Bedienungsanleitung

LCN

LCN 4310ME Series Bedienungsanleitung

LCN

LCN 4050 Series Bedienungsanleitung

LCN

LCN 4600 Series Bedienungsanleitung

LCN

LCN 2010 SERIES Bedienungsanleitung

LCN

LCN ST-2701 Bedienungsanleitung

LCN

LCN 1450 Track Series Bedienungsanleitung

LCN

LCN 8310-2420 Bedienungsanleitung

LCN

LCN 1461 CUSH Bedienungsanleitung

LCN

LCN 4050 Track Series Bedienungsanleitung

LCN

LCN Benchmark III 9140 Bedienungsanleitung

LCN

LCN 8310-2410 Bedienungsanleitung

LCN

LCN COMPACT 6400 Series Bedienungsanleitung

LCN

LCN 4040SE Bedienungsanleitung

LCN

LCN 1261 CUSH Bedienungsanleitung

LCN

LCN 3130-SEL Sentronic Bedienungsanleitung

LCN

LCN 4840 Bedienungsanleitung

LCN

LCN 4630CS Bedienungsanleitung

LCN

LCN 2210DPS Series Bedienungsanleitung

LCN

LCN 4031 CUSH Bedienungsanleitung

LCN

LCN 4040XP Bedienungsanleitung

LCN

LCN 4110EDA Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung