Lectrosonics SMa Series Bedienungsanleitung

Quick

Start

Guide

Fill in for your records:

Serial Number:

Purchase Date:

This guide is intended to assist with

initial setup and operation of your

Lectrosonics product.

For a detailed user manual, down-

load the most current

version at:

www.lectrosonics.com/manuals

SM Series Transmitters

SMA

SMV

SMQV

06 jun10

U.S. Patent 7,225,135

LECTROSONICS, INC.2

Controls and Functions

Battery

Compartment

Opener

Battery

Compartment

Cover Plate

Audio

Input Jack

Antenna

AUDIO Button

LCD Screen

FREQ Button

(Tuning)

Modulation

LEDs

Power LED

UP Arrow

DOWN Arrow

LCD Screen

Used to display the status of the selected function.

Power LED

Indicates power status and battery strength.

Audio Input Jack

Accommodates most lavaliere and dynamic microphones, and line level

signals.

Modulation LEDs

Provides a visual indication of the audio input signal level - either red or green

to indicate modulation levels.

Audio Button

Used to display the audio level setting (0 dB to 44 dB) on the LCD and used

with the Up and Down arrows to adjust the audio level input from the micro-

phone.

FREQ Button

Used to set the operating frequency and toggle the LCD between the operating

frequency in MHz and a two-digit hexadecimal frequency code.

Up/Down Arrows

Used to adjust the selected function or parameter.

Battery Compartment, Cover Plate and Opener

Used to install or remove battery/batteries.

www.lectrosonics.com 3

Operating Instructions

Power On

1) Ensure that good batteries are installed.

2) Simultaneously press and hold the AUDIO

and FREQ buttons until the Power On Boot

Sequence is initiated (3 seconds).

Power Off

1) Simultaneously press and hold the AUDIO and

FREQ buttons while observing that the word

“Off” appears in the LCD along with a counter.

2) When the counter reaches “0”, the unit turns off.

Note: If the AUDIO and FREQ buttons are

released before the end of the countdown, the unit will not turn off.

Standby Mode

From the “OFF” position, quickly press and release

both the AUDIO and FREQ buttons simultaneously

to enter and exit this mode. Allows the user to verify

or change the transmitter’s operating frequency or

audio input level without transmitting any signals.

Selecting the Compatibility Mode and Power (SMV & SMQV ONLY)

SM Series transmitters will work with all Digital

Hybrid Wireless®receivers in the native, compand-

orless mode. They are also capable of working with

200 Series, 100 Series and IFB analog receivers,

plus some other brands of analog wireless receiv-

ers (contact the factory for details).

Note: RF transmission is prevented while selecting Compatibility

Modes. Also, the SM exits the Compatibility Mode screen to Standby

Mode. (See Standby Mode, this section.)

Note: The unit comes from the factory conﬁgured as a 400 Series

transmitter.

1) Set the receiver’s audio controls to minimum.

2) Power up the SM and observe the Boot Sequence. If the Compatibility

Mode for the SM does not match the corresponding receiver, then power

off the SM transmitter.

3) From a power off condition, press and hold the Up arrow, then press the

AUDIO and FREQ buttons simultaneously.

4) The LCD will display the current Compatibility Mode. Use the Up or

Down arrow buttons to set the Compatibility Mode to match the corre-

sponding receiver.

Initial Power On

Timer Screen

Initial Power Off

Timer Screen

Standby Screen

400 Series or Digital

Hybrid Wireless™

Compatibility Mode

LECTROSONICS, INC.4

The following Compatibility Modes are selectable:

• 100 Series mode: CP 100

• 200 Series mode: CP 200

• Mode 3 (Contact factory for details): CP 3

• 400 Series mode: CP 400

• IFB Series mode: CP IFB

• Mode 6 (Contact factory for details): CP 6

5) The Compatibility Mode selected in Step 4 will be the current Compatibili-

ty Mode until reset using this procedure. Pressing AUDIO or FREQ exits

into the Standby Mode. To power off from the compatibility mode screen,

press AUDIO and FREQ together.

6) Press either AUDIO or FREQ button to select

power setting screen and use the up/down

arrows for your desired level of power (50, 100

or 250mw).

Setting Transmitter Operating Frequency

The Operating Frequency of the SM is displayed

either in MHz or as a two-digit hexadecimal num-

ber. Pressing the FREQ button toggles between

the two display modes. The frequency can be set

with the unit in Standby Mode or while powered up

for normal operation.

Note:You must ﬁrst ﬁnd a clear frequency

with the receiver, then set the transmitter to

match.

To change the Operating Frequency of the SM

Series transmitter:

1) Press the FREQ button to enter this screen.

Note: The default display is in MHz. Pressing the FREQ button again

displays the operating frequency as a two-digit hexadecimal number.

2) While holding the FREQ button, use the Up or Down arrow buttons to

move the operating frequency up or down in 100 kHz increments from

the current setting. Holding the Up or Down arrows will cause rapid

scrolling through the frequencies.

Note: The operating frequency displayed on the LCD wraps as it

reaches the upper or lower end of its range. Thus, if you intend to

move the operating frequency from the lower end of the range to the

upper end, it may be faster to do this by using the Down arrow until the

frequency wraps to the upper end.

Adjusting the Low Frequency Roll-off

Repeatedly press the AUDIO button until the LF

roll-off adjustment screen appears. Then press and

hold the AUDIO button while selecting the desired

roll-off frequency with the UP and DOWN arrows.

The roll-off frequency can be set to 35, 50, 70, 100, 120 and 150 Hz.

Frequency displayed as

two-digit hexadecimal

number

Frequency displayed

in MHz

www.lectrosonics.com 5

Attaching a Microphone and Adjusting Gain

The front panel Modulation LEDs indicate limiter ac-

tivity. (See chart below.) Once set, the transmitter’s

audio level setting should not be used to control

the volume of your sound system or recorder levels.

This gain adjustment matches the trans-

mitter gain with the microphone’s output

level, the user’s voice level and the micro-

phone’s position. The audio input level can

be set with the unit in Standby Mode or

powered up for normal operation.

Note: Different voices will usually require different settings of the

AUDIO control, so check this adjustment for each person using the

system. If several different people will be using the transmitter and

there is not time to make the adjustment for each individual, adjust it for

the loudest voice.

1) With the SM powered off, insert the microphone plug into the Audio Input

Jack, aligning the pins and ensuring that the connector locks.

2) Place the SM in Standby Mode, or if the unit is to be powered up and ad-

justed, mute the main sound system prior to powering up the transmitter.

3) Position the microphone in the location where it will be used in actual

operation.

4) Observe the SM audio level LEDs while speaking or singing into the

microphone at the same voice level that will be used during the program.

While holding the AUDIO button, press the Up or Down arrow buttons

until the both the -20 and -10 LEDs glow green, with the -20 LED oc-

casionally ﬂickering red (+0 dB to +10 dB range during peaks).

Note: Setting the audio level too high reduces the dynamic range of the

audio signal. Setting the audio level too low may cause hiss and noise

in the audio.

5) If the unit was set up in Standby Mode, it will be necessary to power up

the SM and adjust the remaining components of the audio system prior to

use.

Locking or Unlocking the Control Panel

The Lock mode protects the transmitter from

accidental changes to its settings.

1) Ensure the SM setup is complete.

2) Simultaneously press both the Up and Down

arrow buttons to start the Lock timer. When

the timer reaches zero, “Loc” is displayed and

the controls are locked.

Important: The only ways to unlock a locked transmitter are to remove

the battery or unlock it via the remote control. It cannot be unlocked

or powered off using the buttons. The remote control will work only if

the transmitter was previously conﬁgured to respond to the remote

control.The unit will always power up in “unlocked” mode.

Signal Level -20 LED -10 LED

Less than -20 dB Off Off

-20 dB to -10 dB Green Off

-10 dB to +0 dB Green Green

+0 dB to +10 dB Red Green

Greater than +10 dB Red Red

LECTROSONICS, INC.6

Battery Installation

We recommend using lithium or high-capacity

rechargeable batteries for longest life.

Note: Standard zinc-carbon batteries marked

“heavy-duty” or “long-lasting” are not adequate.

The battery status circuitry is designed for the volt-

age drop over the life of lithium batteries.

To install new batteries:

1) Turn the Battery Cover Plate Opener counter-

clockwise, open the battery compartment and remove any old batteries.

2) Insert the new battery (or batteries) into the housing, positive (+)

terminal ﬁrst.

Important: On dual-battery transmitters, BOTH

batteries go positive (+) terminal ﬁrst.

3) Replace the Battery Cover Plate and tighten the Opener.

Conﬁguring for Remote Control Use

Some transmitter settings can be changed with the

Lectrosonics RM Remote Control. However, you

must ﬁrst conﬁgure the SM Series transmitter to

accept commands from the RM:

1) Press and hold the Down Arrow Button then

power on the transmitter by pressing the

Audio and Freq buttons simultaneously.

2) The LCD will display the status, either “rc ON” or “rc OFF.” To change the

setting, press the Up or Down arrow button.

3)Power Off the transmitter by pressing the Audio and Freq buttons simulta-

neously. The RC setting will persist when you Power Up the transmitter

again.

Note: SM Series transmitters with ﬁrmware version 1.6 and later are

factory set to “rc ON” by default.

Conﬁguring for Power Restore (SMV & SMQV ONLY)

When using external power source through a

battery eliminator, Power Restore will return

your transmitter to settings it had before it was

powered off. This eliminates the need to power on

through the unit itself.

1) Press and hold the Down Arrow Button then

power on the transmitter by pressing the

Audio and Freq buttons simultaneously.

2) The LCD will display the status, either “rc ON” or “rc OFF.” Press “AUDIO”

or “FREQ” key to scroll to the “PbAc 0” setting and use arrow keys to

turn to “PbAc 1” for on.

3)When power is restored the unit will turn on with previous settings.

Power Restore Screens

Remote Control Screens

www.lectrosonics.com 7

LCD Display

Battery Cover

Knob/

Lanyard

Attachment

AUDIO Button

Battery Level

Indicator

UP Arrow

Button

SEND

Button

DOWN Arrow

Button

Speaker

FREQ Button

RM Remote Control Operating Instructions

The RM gives you remote control of SM Series transmitters using an audible

tone delivered to the transmitter’s microphone. When the SEND button is

pressed, a “dweedle” tone will play from the RM speaker and the parameter on

the transmitter will be set immediately. The transmitter must be conﬁgured to

accept commands from the RM (see page 6). Adjustments can be made to set:

• Audio input gain

• Frequency

• Lock or Unlock modes

• Sleep mode ON/OFF

In the power saving sleep mode, power consumption drops to 20% of normal.

Powering the RM On and Off

Press the AUDIO and FREQ buttons together brieﬂy.

Principles of Operation

The RM user interface is organized into pages which are accessible via the

AUDIO and FREQ buttons. Once on a page, settings can be adjusted with the

UP and DOWN arrow buttons. Only the speciﬁc function displayed is altered.

The AUDIO button cycles through 4 pages:

1) Aud - set transmitter’s audio level

2) SLEEP/unSLP - cause transmitter to sleep or wake up

3) Loc/unLoc - lock or unlock transmitter’s buttons

4) Loud - adjust RM speaker volume (press SEND button for a sample tone)

The FREQ button cycles through 3 pages:

1) CH - set transmitter’s channel (using block-independent hex code)

2) b - select a block number (optional — uncovers page 3)

3) 000.000 - set transmitter’s frequency in MHz (avail. if a block is selected)

Note: The speaker should be uncovered and

held within a few inches of the transmitter’s

microphone. The longest usable range is about

6 feet, depending on the microphone and volume

settings.

Andere Handbücher für SMa Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lectrosonics Sender Handbücher

Lectrosonics

Lectrosonics M2T/E01 Non Dante Bedienungsanleitung

Lectrosonics

Lectrosonics DHu Bedienungsanleitung

Lectrosonics

Lectrosonics UM400 Bedienungsanleitung

Lectrosonics

Lectrosonics MM400 Bedienungsanleitung

Lectrosonics

Lectrosonics UT Bedienungsanleitung

Lectrosonics

Lectrosonics UH400A Bedienungsanleitung

Lectrosonics

Lectrosonics IFBT4/E01 Bedienungsanleitung

Lectrosonics

Lectrosonics MM400B Bedienungsanleitung

Lectrosonics

Lectrosonics SM Series Bedienungsanleitung

Lectrosonics

Lectrosonics WM Bedienungsanleitung

Lectrosonics

Lectrosonics Digital Hybrid Wireless SSM Bedienungsanleitung

Lectrosonics

Lectrosonics DBu Bedienungsanleitung

Lectrosonics

Lectrosonics M2T/ND Bedienungsanleitung

Lectrosonics

Lectrosonics SM Bedienungsanleitung

Lectrosonics

Lectrosonics LT Bedienungsanleitung

Lectrosonics

Lectrosonics UT700 Bedienungsanleitung

Lectrosonics

Lectrosonics HHa-941 Bedienungsanleitung

Lectrosonics

Lectrosonics SMDB/E01 Series Bedienungsanleitung

Lectrosonics

Lectrosonics D4 Bedienungsanleitung

Lectrosonics

Lectrosonics UH200D Bedienungsanleitung

Lectrosonics

Lectrosonics UM195B Bedienungsanleitung

Lectrosonics

Lectrosonics M185 Bedienungsanleitung

Lectrosonics

Lectrosonics IFBT4-VHF/X Bedienungsanleitung

Lectrosonics

Lectrosonics SMV-941 Series Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung