Ledj STAR18 Bedienungsanleitung

LEDJ Tri LED Matrix Table Cloth - STAR18

USER MANUAL

www.prolight.co.uk

LEDJ Tri LED Matrix Table Cloth Safety

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modifications to this equipment are not

subject to warranty.

LEDJ Tri LED Matrix Table Cloth Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modification to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to flammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualified engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature fluctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualified

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should find inside the carton the following items:

1, Tri LED Matrix Table Cloth 2, Instruction manual 3, Controller 4, SD card

Technical Specifications:

DMX channels: 2

DMX, sound active and auto run modes

72 Ultra Bright Tri-colour LEDs

Hanging tabs on 3 sides

Fire retardent material

Power consumption: 25W

Power supply: 240V

Dimensions: 2.2 x 1M

Weight: 4Kgs

Overview:

LEDJ Tri LED Matrix Table Cloth Technical Specifications

Order code: STAR18

DMX IN DMX OUT SIGNAL DC OUT

DIPSWITCHES

MIC SENS

www.prolight.co.uk

POWER

SUPPLY

OFF

Operations:

There are three operating modes to choose from;

1, Auto run 2, Sound Active 3, DMX

NOTE: Before use, please insert the supplied SD card and follow the instructions below.

Auto run mode

To set the Matrix table cloth in auto run mode, set all dip switches to the off position and use the

“SENSITIVITY/SPEED” control to set the desired running speed. The Matrix table cloth will now

run through all of its in-built programmes.

Sound active mode

To set the Matrix table cloth into sound active mode, set dip switch “10” to the ON position and

all others to the OFF position. Now use the “SENSITIVITY/SPEED” control to set the desired

sensitivity level.

DMX mode

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest flexibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of the

cloth and each cloth independently. The Tri LED Matrix Table Cloth uses 2 channels of

control.

Use dip switches 1 – 9 to address each cloth accordingly.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each cloth requires a “start address”

from 1- 511. A cloth requiring one or more channels for control begins to read the data on the

channel indicated by the start address. For example, a cloth that occupies or uses 7 channels

of DMX and was addressed to start on DMX channel 100, would read data from channels:

100,101,102,103,104,105 and 106. Choose a start address so that the channels used do not

overlap. E.g. the next unit in the chain starts at 107.

DMX chart:

LEDJ Tri LED Matrix Table Cloth Operations

Channel

Value

0-9

10-255

10-239

Function

Blackout

Sound Active

Pattern selector

0-9 Blackout

0-255 Speed (slow to fast)

Notes

CH1 0-9 Blackout

240-255 Auto run

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest flexibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the fixture and each fixture independently.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each fixture requires a

“start address” from 1- 511. A fixture requiring one or more channels for control begins to read the

data on the channel indicated by the start address. For example, a fixture that occupies or uses 7

channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all fixtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX fixtures try to use the

shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The LEDJ Tri LED Matrix Table Cloth can be controlled via DMX-512 protocol. The DMX

address is set on the back of the unit. Your unit and your DMX controller require a standard

3-pin XLR connector for data input/output (figure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

LEDJ Tri LED Matrix Table Cloth DMX Set Up

Notice:

• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

LEDJ Tri LED Matrix Table Cloth DMX Set Up

LEDJ Tri LED Matrix Table Cloth Dip Switch Reference Chart

DMX Dip Switch Quick Reference Chart

Dip Switch Position

Inhaltsverzeichnis

Andere Ledj Scheinwerfer Handbücher

Ledj

Ledj Xterior Wash 131 Bedienungsanleitung

Ledj

Ledj STAGE WASH U.V. 36 LEDJ106 Bedienungsanleitung

Ledj

Ledj INTENSE 12D4 CW Bedienungsanleitung

Ledj

Ledj LEDJ280 Bedienungsanleitung

Ledj

Ledj Q Colour LEDJ210 Bedienungsanleitung

Ledj

Ledj ALU ZOOM PAR 64 Bedienungsanleitung

Ledj

Ledj Q Batten LEDJ300 Bedienungsanleitung

Ledj

Ledj ALU ZOOM PAR 64 Bedienungsanleitung

Ledj

Ledj LEDJ252B Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Ledj

Ledj LEDJ98 Bedienungsanleitung

Ledj

Ledj Q Colour Bedienungsanleitung

Ledj

Ledj HEX Par 7 Bedienungsanleitung

Ledj

Ledj ALU ZOOM PAR 64 Bedienungsanleitung

Ledj

Ledj LEDJ286 Bedienungsanleitung

Ledj

Ledj Spectra Par 6HEX10 Bedienungsanleitung

Ledj

Ledj Spectra Led Flood (Exterior) Bedienungsanleitung

Ledj

Ledj Stage Wash 18 Bedienungsanleitung

Ledj

Ledj 19T3 Bedienungsanleitung

Ledj

Ledj PERFORMER 54 RGBW Bedienungsanleitung

Ledj

Ledj Intense 9HEX10 Bedienungsanleitung

Ledj

Ledj Slimline 5Q5 Bedienungsanleitung

Ledj

Ledj Performer 18 Quad Zoom Bedienungsanleitung

Ledj

Ledj STAGE COLOUR 24 TRI Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Bedienungsanleitung