LEGO Horizon Express 10233 Bedienungsanleitung

10233 Horizon Express

Welcome to text-based instructions from LEGO for the Blind. Before you start building, here are some

terms we’ll be using:

Front: towards you.

Back: away from you.

Up: towards the ceiling.

Down: towards the floor.

Stud: the bump on a Lego brick. Example: A 2x1 brick has two studs on it.

Vertically: going from front to back.

Horizontally: going from left to right.

Upright: pointing up towards the ceiling, and down towards the floor.

Symmetrically: a mirror image. Example: If you place a 2x1 brick with technic connector on the

front wall at the right, connector to the front, and then place another such piece symmetrically on

the back wall, at the right, the technic connector of the second piece should point to the back,

since it will be placed symmetrically.

There are also abbreviations defined at the end of this file.

Fly down the track in the Horizon Express!

Book 1. Engine.

Book 2. passenger car.

Book 3. Cafe/dining Car

Book 1.

Make a minifigure, it’s a girl with gray pants, blue shirt, striped, orange-gray vest and long braided hair.

Bag 1.

Put a 28x6 with two holes hor on the table.

Put a F 4x2 ver on the right edge, in the middle, overhanging to

the right.

Bag 2.

Put a 3x2 hor to the left, in the middle.

Put a 6x1 hor in the right back corner.

Repeat symm at the front.

Put a 6x1 ver to the left of the two PPs.

Put a 2x1 hor to the left, at the back edge.

Repeat symm at the front.

Put a 3x2 hor to the left and to the back.

Repeat symm at the back.

Put a 6x1 hor to the left.

Repeat symm at the front.

Put a 2x1 slide ver to the left and to the back, slide to the

back.

Repeat symm at the back.

Bag 3.

Put a 2x1 ver to the left.

Repeat symm at the front.

Put a F 6x2 ver to the left of the two PPs.

Put a F 4x2 hor to the left, at the back edge.

Repeat symm at the front.

Put a F 2x2 disk to the back of the two left columns of the PP.

Put a grate hor at the left back corner.

Repeat symm at the front.

Put a F 4x2 from a sep bag ver between the two PPs.

Bag 4.

Skip one column from the left and put a F 2x2 in the middle.

Put a F 2x1 with one button ver to the back of the right column

of the PP.

Repeat symm at the front.

Put a grate hor to right, at the front edge.

Repeat symm at the back.

Put a F three-button corner piece to the front, letter F.

Put a F three-button corner piece to the front, letter H.

Put a F 2x1 with one button ver to the right and to the front.

Repeat symm at the back.

Stack two F 2x1 and put hor to the right, at the back edge.

Repeat symm at the front.

Bag 5.

Put a FS 2x1 with a handle hor to the back, slide to the back.

Repeat symm at the back.

Put a 1x1 wedge to the right, slide to the front.

Repeat symm at the front.

Put a F 3x1 hor at the front right corner.

Put a F 12x1 hor to the left.

Put a F 6x1 hor to the left.

Repeat steps 5-7 symm at the back.

Put a three-button corner piece at the right edge, skipping the

front row, letter H.

Put a three-button corner piece to the back, letter F. Put a f6x2

hor to the left of the two pps in the middle. Put aside.

Bag 6. Make a part.

Put a 2x2/2x2 on the table, the holed side down and the buttons

upright at the left. Put a F 1x1 with a clasp upright, hor, clasp

overhanging to the front, on the front bottom button. Put another

such piece symm at the back. Put another such piece the same way

to the top. Put another such piece symm to the front.

Put a 2x2 ribbed cylinder sideways to the left. Put a F 2x2 disk

sideways to the left. Put another ribbed 2x2 cylinder to the

left.

Put four other F 1x1 with a clasp to the left, as before.

Put a 2x2/2x2 to the left and underneath, the same way as the

first one.

Put a ringed stick hor, the ring to the left, at the front bottom

two clasps.

Put another such stick to the top, as before.

Put two more such sticks at the back, as before.

Install as is in the middle of the right side.

Bag 7.

Put a three-button corner piece on the front right corner and to

the right, letter F.

Put a FS 8x1 hor to the left, at the front edge.

Stack two F 2x1 and put hor to the left.

Put a 2x1 hor to the back.

Repeat steps 1-4 symm at the back.

Bag 8.

Put a three-button corner piece on the front right corner and to

the right, letter F.

Skip eight columns to the left and put a 2x2 there.

Put a F 2x1 ver on the left column of the PP.

Repeat steps 1-3 symm at the back. Put aside.

Bag 9. Bags 9-14 make the black and white arrow patterns on the

right front and back sides.

Make a part. Put a F 2x1 hor on the table. Put a F 1x1 with a

clasp ver on the right button, the clasp overhanging to the

front. Repeat to the left. Put two 1x1 wedges on top, left slide

to the left, right to the right.

Repeat step 1 to make two such parts.

Hold your part so that the wedges are at the left and clasps are

at the back. Install one upright, ver, the clasps to the back, on

the front edge, on the second column from the right, by inserting

the sticks into the clasps.

Install the other symm at the back. LMA.

Make a part. Hold a 2x2/2x1 corner piece upright, ver, the 2x1

to the top and the 2x2 to the right. Mount a F 2x1 upright, ver,

on the back upper and lower buttons of the 2x2 side. Put two

wedges on the PP, slides to the middle.

Skip eight columns from the right at the back edge and mount this

part as is on the 2x2 there, to the right of the F 2x1.

Repeat step 6, but put a F 2x1 on the front upper and lower

buttons. The wedges go on top of it.

Put this part symm at the front.

Bag 10.

Make a part. Put a F 1x1 with a clasp from a sep bag (white) ver

on the table, the clasp to the back. Put a wedge from a sep bag

on top, slide to the left.

Repeat three times to make four.

Install one upright, hor, the clasp to the back, the wedge to the

left on the front edge, on the third column from the right, the

clasp on the bottom stick and the wedge underneath the wedge

already there.

Install the second such part to the left, upright, hor, the clasp

to the back, the wedge to the left.

Repeat step 1 with the rest of the pieces (black).

Put two of the new parts (black) to the left, as in steps 3-4.

Put the two old parts (white) to the left, as in steps 3-4.

Bag 11.

Make a part. Put a F 1x1 with a clasp from a sep bag ver on the

table, the clasp to the back. Put a wedge on top, the slide to

the right.

Repeat three times to make four. Install one upright, the clasp

to the back, the wedge to the right, on the front edge, on the

third column from the right, on top of the part from the previous

bag, the upper stick on the clasp.

Install the second such part to the left, upright, hor, the clasp

to the back, the wedge to the left.

Repeat step 1 with the rest of the pieces (black).

Put two of the new parts (black) to the left, as in steps 3-4.

Put the two old parts (white) to the left, as in steps 3-4.

Bags 12-13. Rotate your structure back to front (and left to

right) and repeat bags 10-11.

Bag 14. Rotate your structure back to front (and left to right).

Stack two 1x1 pieces and put on the front edge, skipping six

columns from the left.

Put a ridged 2x1 hor to the right, the vertical ridges to the

front.

Repeat four times.

Repeat steps 1-3 symm at the back. LMA.

Bag 15.

Make a part. Stack two 1x1 with handles, the handles on the same

side. Put a FS 1x1 on top.

Repeat to make two.

Put one on the front edge, skipping five columns from the left,

the handles to the front.

Put the other symm at the back.

Put five ridged 2x1 at the back, and five at the front, on top of

other such pieces, as before.

Bag 16.

Put a F 2x1 hor on the front edge, skipping five columns from the

left (overhanging a little to the front).

Put a F 3x1 hor on top of the PP and to the right.

Put a F 8x1 hor to the right.

Put a F 12x1 hor to the right.

Put a 2x1 to the back of the rightmost button and to the right.

Repeat steps 1-5 symm at the back.

Bag 17.

Make a part. Put a F 2x1 from a sep bag (brown) hor on the table.

Put a F 2x1 (orange) hor on top.

Take a 2x1/2x2 from a sep bag (gray) hor on the table, the 2x2

side buttons to the front, and put the stack from step 1 hor on

top of the 2x1 bottom side. Put a 2x1 shelf piece hor on top, the

smooth wall to the front.

Mount a 2x2/2x1 hor on top, the 2x2 side buttons to the front and

to the bottom. Mount a F 4x2 upright, ver, to the front of your

part.

Mount a FS 4x2 on top of the PP. (These two pieces are divided on

the smooth side into a black and orange triangle, one left and

one right. Ask a sighted person to help with installation).

Repeat steps 1-4 to make two such parts.

Install one on the front edge, skipping three columns from the

left, the shelf to the back.

Repeat symm at the back.

Bag 18.

Make a part. Stack two 1x1 with handles, the handles on the same

side. Put a FS 1x1 on top.

Repeat to make two.

Install one on the front edge, skipping two columns from the

left, the handles to the front.

Repeat symm at the back.

Put a F 12x1 hor on the front edge, skipping five columns from

the left.

Put a F 3x1 hor to the right.

Put a F 8x1 hor to the right.

Repeat steps 5-7 symm at the back. Lay aside.

Bag 19. Make the cabin (the front of the train, at the left).

Number 1.

Put a 2x1/2x1 step piece with two side buttons ver on the table,

the side buttons to the left.

Put the other such piece the same way to the back.

Connect by putting a F 10x2 hor on the lower steps, in the

middle, overhanging to the right.

Number 2.

Put a 6x2 step piece with four side buttons hor underneath the

front row of the 10x2 piece, the side buttons to the front, to

the right of the 2x1/2x1 piece.

Repeat symm at the back.

Number 3.

Put a 2x1 ribbed slide piece hor on the front edge, skipping the

leftmost button, the slide to the right.

Repeat symm at the back.

Put a FS 4x2 hor in between the two PPs and to the right.

Put a FS 2x1 ver to the right.

Put a f2x1 with a vertical clasp hor to the right of the front

row of the PP, the clasp to the right.

Repeat symm to the back.

Number 4.

Put a seat piece ver to the right, the back of the seat to the

right.

Skip one column to the left and put a F 2x1 ver there, to the

left of the clasps.

Put a 2x1 with vertical clasp ver in the middle of the left edge

clasp to the right, LMA.

Number 5. Make the tip of the train part.

Put a 2x2 slide hor on the table, the slide to the front.

Put a 4x1 receiver piece hor on top and to the sides.

Make two stacks of two F 1x1 pieces and put underneath the sides

of the PP.

Affix a sticker (a black strip) on top of the receiver piece.

Install sideways, ver, the receiver and slide to the left, on the

left edge of your main part, on the four side buttons there. LMA.

Number 6.

Make a part. Put a 1x1 with a side button on the table, the side

button to the left. Mount a 1x1 wedge from a sep bag

(transparent) on the side button, the slide to the top.

Repeat to make two.

Put one, as is, on the front edge, skipping one column from the

left (not counting the receiver).

Repeat symm at the back.

Skip two columns to the right and put a 2x1 with the side buttons

hor there, the side buttons to the front.

Repeat at the front (the side buttons to the front).

Skip one column to the right and put a 1x1 wedge on the second

row from the front, the slide to the right.

Put a 1x1 wedge to the back, the slide to the right. LMA.

Number 7.

Make a part. Put a F 4x1 hor on the table. Put a FS 4x2 hor on

top and overhanging to the front.

Put a F 2x1 with a handle hor underneath the overhanging end, in

the middle, the handle to the front. Affix a sticker (with the

gauges and levers) on top. Install diagonally, hor, the sticker

to the right, to the left of the seat, inserting the handle into

the two clasps there. Lay aside.

Number 8. Make a part.

Put a F 6x2 hor on the table. Put a F 2x1 ver on top, on the

right edge.

Put a F 4x2 hor to the left.

Put a F three-button corner piece on the table, to the left of

your part, letter j.

Connect it by putting another such piece, letter j, on top of the

dot five and on top of the left edge of your main part.

Put a S 4x1 curve hor, slide to the left, on the front edge, on

the two leftmost columns and to the left.

Put a S 4x1 curve from a sep bag hor to the back and to the

right.

Install upright, hor, the curves to the front at the left, on the

front edge of your main part. LMA.

Number 9. Make a part.

Put a F 6x2 hor on the table. Put a F 2x1 ver on the right edge.

Put a F 4x2 hor to the left.

Put a F three-button corner piece on the table, to the left of

your part, letter D (1-4-5).

Connect it by putting another such piece, letter D, on top of the

dot four and on top of the left edge of your main part.

Put a S 4x1 curve from a sep bag hor, slide to the left, on the

front edge, on the two leftmost columns and to the left.

Put a S 4x1 curve hor to the back and to the left.

Install symm at the back. Put a fs4x1 hor on the front upright

to the right of the upper s curve. Put a fs6x1 hor below it, then

put a fs1x1 on the upper-right corner. Repeat symm at the back.

LMA.

Number 10. Make a part.

Put an 8x6 end piece hor on the table, the slide to the left.

Put another such piece the same way on the top, skipping two

leftmost columns.

Put a 1x1 underneath the protruding front edge, on the second

column from the right.

Repeat symm at the back.

Install as is on top of your main part, skipping the leftmost

column and overhanging one column to the right.

Number 11.

Flip your part upside down. Put a 4x1 with side railings hor,

upside down, the railings to the front, on the third row from the

front, on the 5th-9th columns from the left (not counting the

receiver).

Put another such piece hor to the back, symm.

Number 12.

Flip right side up. Affix two stickers with the number 14 on them

to the front and to the back, in the middle level, at the right

end.

Install as is to the left end of your structure, on the two

leftmost columns and overhanging to the left. The insert picture

shows the finger pressing on the seat.

Bag 20.

Put a 3x1 hor on the right end of the front wall.

Skip two columns to the left and put a 4x1 hor there.

Put a F 6x1 hor to the left.

Repeat.

Repeat steps 1-4 symm at the back.

Bag 21.

Put a F 4x2 ver in the middle of the right edge and to the right.

Put a FS 4x1 ver on top, on the right column.

Skip ten columns from the right edge and put a F 4x1 hor on the

front wall.

Repeat symm at the back.

Put a F 6x1 hor to the left.

Repeat symm at the front.

Put a F 1x1 to the left.

Repeat symm at the back.

Put a F 6x1 ver to the left of the two PPs.

Bag 22.

Put a F 4x1 ver on top of the PP, in the middle.

Put a FS 6x1 hor to the front and to the right.

Put a FS 6x1 hor to the right.

Inhaltsverzeichnis

Andere LEGO Spielzeug Handbücher

LEGO

LEGO Mindstorms Education 9695 Bedienungsanleitung

LEGO

LEGO NinjaGQ 70746 Bedienungsanleitung

LEGO

LEGO Disney FROZEN 41147 Bedienungsanleitung

LEGO

LEGO 3451 Bedienungsanleitung

LEGO

LEGO SUPER HEROES 76032 Bedienungsanleitung

LEGO

LEGO MARVEL SUPER HEROES ULTIMATE SPIDER-MAN... Bedienungsanleitung

LEGO

LEGO legends of chima 70145 Bedienungsanleitung

LEGO

LEGO legends of chima 70146 Bedienungsanleitung

LEGO

LEGO 10229 Bedienungsanleitung

LEGO

LEGO 75130 Bedienungsanleitung

LEGO

LEGO Nexo Nights 70321 Betriebsanleitung

LEGO

LEGO Star Wars Cloud City 10123 Bedienungsanleitung

LEGO

LEGO HOBBIT 79003 Bedienungsanleitung

LEGO

LEGO Space Police 5972 Bedienungsanleitung

LEGO

LEGO MindStorms RoboSports 9730 Bedienungsanleitung

LEGO

LEGO Friends 41037 Bedienungsanleitung

LEGO

LEGO DIMENSIONS 71201 Bedienungsanleitung

LEGO

LEGO 4950 System Bedienungsanleitung

LEGO

LEGO 79007 Bedienungsanleitung

LEGO

LEGO 75051 Bedienungsanleitung

LEGO

LEGO 76028 DC Comics Super Heroes Bedienungsanleitung

LEGO

LEGO 41072 Bedienungsanleitung

LEGO

LEGO 10665 Juniors Bedienungsanleitung

LEGO

LEGO Prehistoric Power 4892-1 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung

Ravensburger

Ravensburger 3D Puzzle La Tour Eiffel Bedienungsanleitung

Trix

Trix 24432 Bedienungsanleitung