LEGRAND Kenall LOW PROFILE SCONCE LPS Series Bedienungsanleitung

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

LPS_F-5290_090418

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions

should always be followed, including the following:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE

APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH

THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND

THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS

BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH

ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT

TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS

AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.

SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE

FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING

ORIENTATION, OR MOUNTING RESTRICTIONS.

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

LPS SERIES –SEMI-RECESSED MOUNT –NEW CONSTRUCTION

LOW PROFILE SCONCE™

Back Cover

Screw

Back Cover

1. Back out screw(s) at bottom or side of housing

until baseplate can be easily removed.

2. Remove baseplate.

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

LPS_F-5290_090418

4. After the Drywall has been installed, cut a rectangular hole ( recommended hole 3-3/8" x 9" ) and insert the

mounting-housing making sure that the hooks on housing are pointing up. Attach housing to back-box using

the four (4) 1.5" screws provided with the xture.

Brackets

Hanger bars

Back-box Knockout

Screws

a-b c

Studs

Screws

(Supplied

by others)

3. Mount Back-box and Hanger Bars.

a. Remove knockouts as needed.

b. Mount back-box to hanger bars using the screws and brackets supplied with the xture.

c. Install hanger bar assembly. Use four screws per hanger bar (supplied by others).

Note: Remember to use non-ferrous hardware when installing MRI xtures.

Back-box

Cutout

Drywall Drywall

Hooks

1.5" Screws

Mounting-Housing

3.375

9.000

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

LPS_F-5290_090418

5. Make electrical connections. Disconnect facility power to the electric power supply leads. Connect xture leads

to power supply leads using connectors suitable for the gage and number of wires being used (not included).

MRI Fixtures:

a. If a 0-10V dimming circuit is to be connected, install at this time. The 0-10V dimmer must be installed

outside the shielded MRI environment with the Kenall MRIFD-1A dimming line lter (or equivalent)

installed in accordance with the supplied installation instructions. Kenall recommends the Lutron Diva

(DVSTV) and Lutron Nova T (NTSTV-DV) series to ensure the full range of dimming can be achieved.

b. Run DC supply wiring, equal in size and temperature rating to the lter input wiring, between the lter

output cables and the rst luminaire within the shielded room. Follow recommended wiring layout

described below. All wiring must be within completely-enclosed, grounded conduit suitable for an MRI

environment. Any gaps, regardless of size, must be closed or wrapped in copper foil tape. Special attention

should be paid to the wiring entry point into the shielded space. Class 1 wiring methods are required.

c. Run the dimming signal wiring, equal in specication to the lter input wiring, between the lter output

cables and the rst luminaire within the shielded room. Maintain polarity between input and output sides

of the lter and follow wiring recommendation below. All wiring must be within completely enclosed,

grounded conduit suitable for an MRI environment. Any gaps, regardless of size, must be closed or wrapped

in copper foil tape. Special attention should be paid to the wiring entry point into the shielded space. Cap

gray and violet leads at luminaire(s) if dimming function is not implemented.

NOTES: To prevent MRI machine interference, all DC power and dimming signal wiring must be completely shielded

within grounded conduit.

Luminaire 1

Luminaire 2

Luminaire N

(last)

EMI

Filter

EMI

Filter

RED

BLACK

VIOLET

GRAY

BLACK

RED

Repeat

Wiring As

Needed

INSIDE MRI ROOMOUTSIDE MRI ROOM

–

NOTE: ALL WIRES INSIDE MRI ROOM TO BE

INSIDE GROUNDED RIDGID ALUMINUM CONDUIT

0-10V Dimmer

(by others)

COMMON

HOT MRIPSF-480

MRIFD-1A

(or equal)

120-277VAC

50/60 Hz

24V

–

Single-Supply System Schematic

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

LPS_F-5290_090418

Mounting

Hooks

Top of housing

(No hole)

Screw

6. Install xture. Top of housing over top of housing's hooks.

7. Tighten screw at bottom of housing.

For technical assistance, call 1-800-4KENALL (1-800-453-6255).

CUSTOMER SERVICE

For warranty information visit www.kenall.com/Resources/Certied-Performance-Warranties

WARRANTY

Inhaltsverzeichnis

Andere LEGRAND Rack & Stand Handbücher

LEGRAND

LEGRAND CHIEF PSB2087 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF TIL1X2PT Bedienungsanleitung

LEGRAND

LEGRAND Chief FCA850 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF Koncis DMA Series Bedienungsanleitung

LEGRAND

LEGRAND CHIEF UU Series Bedienungsanleitung

LEGRAND

LEGRAND CHIEF TILD1 XNE1 Series Bedienungsanleitung

LEGRAND

LEGRAND Chief PAC800HS Bedienungsanleitung

LEGRAND

LEGRAND CHIEF IntelliSHOT PAC800E Bedienungsanleitung

LEGRAND

LEGRAND SANUS WSSE1A1 Bedienungsanleitung

LEGRAND

LEGRAND Chief Koncis D1U Bedienungsanleitung

LEGRAND

LEGRAND CHIEF Koncis DMA1 Bedienungsanleitung

LEGRAND

LEGRAND bticino MyHOME 3487AP Bedienungsanleitung

LEGRAND

LEGRAND Sanus LMF219 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF HTSTS Bedienungsanleitung

LEGRAND

LEGRAND CHIEF PRSU Bedienungsanleitung

LEGRAND

LEGRAND SANUS VDLF28 Bedienungsanleitung

LEGRAND

LEGRAND PX2 Bedienungsanleitung

LEGRAND

LEGRAND SANUS WSSE3A1 Bedienungsanleitung

LEGRAND

LEGRAND Sanus WSWME31 Bedienungsanleitung

LEGRAND

LEGRAND SANUS WSSE31 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF OMNDBF46-55 Bedienungsanleitung

LEGRAND

LEGRAND DA-LITE 203 Bedienungsanleitung

LEGRAND

LEGRAND SANUS ACCENTS ARTVF1 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF FSB4442 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung