Leica ML180 Series Bedienungsanleitung

Get Prepared

FAQs Leica Lino ML

PAIRING XCRCatch

The ML 180 and the receiver should be paired already. However, if some problems occur with the connec-

tion between device and receiver, repeat the pairing procedure - follow the instructions below. (Take care

that you press all 3 buttons on the device simultaneously to switch it on...)

SMART TARGETING: LONG PRESS

How long should I press the Smart Targeting key?

Make sure, that the Smart Targeting key is pressed min.

2sec –press it as long as 2 red LEDS start to blink on

the XCR Catch receiver. Now you can position the re-

ceiver on your target and the ML device starts to rotate so that the laser beam catches the

receiver. This can be done in a range of +/- 4°. (To set the device to 0° position, press

Smart Targeting key short.)

2 mebe/23.8.2016

SMART TARGETING - PAIRING : SHORT PRESS

If I press the Smart Targeting key short, the device starts to rotate –what does this mean?

Pressing the Smart targeting function shortly means that the device goes back to the 0° (default

position in the middle). This is the position, where you have on both sides a +4° and -4° searching

range for the Smart Targeting. At a distance of 20m, this means a transverse distance of +/- 1.4 m

up from the 0° position (=total: 2.8m). You can check the laser position with the 3 lines, which are

stamped below the handle. The 0° position is achieved, if the line from the metallic base plate is in

the middle of the 3 lines from the plastic housing ( Make sure, that the feet are folded in).

SMART TARGETING OVER DISTANCE

The Smart Targeting function does not work on longer distances?

The Smart Targeting function (automatic alignment) works only until 50m. The distance range is

dependent on the surrounding conditions (obstacles, other radio controlled devices,...). If it is used

above 50m, the Smart Targeting could be slower or it could occur, that it even does not catch the

laser beam properly. The distance range for the standard line location of the XCR catch receiver is

longer, it works up to 100m.

If the sensitivity is enlarged to 5mm, this supports the targeting.

We recommend to use Smart Targeting function at a minimum distance of 5m.

SMART TARGETING –LASER BEAM ALREADY ON WINDOW

The Smart Targeting function cannot be started if the laser beam is visible on the receiver

window?

If the laser beam is visible on the window, it was already targeted by the XCR catch receiver. In

this position the Smart Targeting function will not start if you press the function key long. If you face

this circumstances, remove the XCR Catch receiver completely outside the laser beam, press

again the Smart Targeting key long until the 2 LEDs blink. The Smart Targeting function starts now

and the XCR Catch can be moved back to the original position. Another option to solve this issue,

is to use the continuous targeting mode. Press Sensitivity + Smart targeting key simultaneously

and the laser beam follows the XCR catch receiver continuously until it is stopped by pressing the

Smart targeting key again.

*When starting Smart Targeting, position the laser slightly off line

3 mebe/23.8.2016

CONTINOUS SMART TARGETING FUNCTION (Automatic alignment)

The continuous Smart Targeting function is selected, but does not start?

Pressing Sensitivity key and Smart Targeting key simultaneously is sometimes difficult to handle. If

the Sensitivity key is pressed first, it changes only the sensitivity and you see that the sensitivity

icon changes in the display and the continuous function is not activated. To overcome this effect,

we recommend to press first the Smart targeting key and shortly afterwards additionally the sensi-

tivity key. If you release the keys, 2 small blinking arrows appear on the display near the Smart

Targeting icon.

ADDITIONAL INFORMATION

MANUAL ROTATION

The device is rotated manually with the knob and it does not move right from the begin-

ning?

It is a normal behaviour, that it takes few manual turns to move finally the laser beam. The ML de-

vice is focused on targeting laser beams at large distances and this “slow down effect”prevents

displacing the beam due to small accidental pushes.

BASE PLATE IS MOVING

The base plate is not fixed properly - is this a mistake?

The base plate can be moved manually. This is on purpose as this is the movement for the +/-4°

rotation.

LEVELLING PROCEDURE

The vertical lines switch off, if the device is levelling?

The high accurate electronic levelling needs power and therefore the vertical lines can shut off dur-

ing the levelling procedure. This is to save power and to speed up the levelling. After finalizing, the

lines shut on automatically and you can work as usual.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Leica Laser-Nivelliergerät Handbücher

Leica

Leica Wild t1010 Bedienungsanleitung

Leica

Leica LS10 Bedienungsanleitung

Leica

Leica Rod Eye Basic Bedienungsanleitung

Leica

Leica LS10 Bedienungsanleitung

Leica

Leica Lino L2 Bedienungsanleitung

Leica

Leica BLK ARC Bedienungsanleitung

Leica

Leica NA720 Bedienungsanleitung

Leica

Leica Rugby 640 Bedienungsanleitung

Leica

Leica DISTO D3a BT Bedienungsanleitung

Leica

Leica N3-70 Bedienungsanleitung

Leica

Leica 3D Disto Bedienungsanleitung

Leica

Leica TPS1200 series Bedienungsanleitung

Leica

Leica Sprinter 50 Bedienungsanleitung

Leica

Leica Rugby 200 Bedienungsanleitung

Leica

Leica Rugby 100 Bedienungsanleitung

Leica

Leica Rugby 260SG Bedienungsanleitung

Leica

Leica Rugby 820 Bedienungsanleitung

Leica

Leica iCON robot 60 Bedienungsanleitung

Leica

Leica Rugby 880 Bedienungsanleitung

Leica

Leica LINO L6R Bedienungsanleitung

Leica

Leica Rugby 670 Bedienungsanleitung

Leica

Leica Lino L360 Bedienungsanleitung

Leica

Leica Lino P5 Bedienungsanleitung

Leica

Leica Jogger 20 Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken

Nedo

Nedo ET-5 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung

LaserLiner

LaserLiner X2-Laser Bedienungsanleitung

Spectra

Spectra LL300N Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung

Nedo

Nedo Crossliner 4 Bedienungsanleitung

Lasertec

Lasertec FX360G Bedienungsanleitung

Flex

Flex ALC 8 Bedienungsanleitung

Black & Decker

Black & Decker LZR5 Bedienungsanleitung

Johnson

Johnson 40-6692 Bedienungsanleitung

Cocraft

Cocraft HL 20-SG Bedienungsanleitung

Zircon

Zircon iLine Bedienungsanleitung

HWH

HWH 310 SERIES Bedienungsanleitung

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Bedienungsanleitung

LaserLiner

LaserLiner ActiveFinder XP Bedienungsanleitung

DeWalt

DeWalt DW082 Bedienungsanleitung

imex

imex EL20 Bedienungsanleitung

Fixturlaser

Fixturlaser NXA D I-0912 Bedienungsanleitung