LevelOne FVT-2002 Bedienungsanleitung

Copper to Fiber

Stand-Alone Media Converter

Quick Installation Guide

Model

No.

Description

FVT-2001

10/100BASE-TX to 100BASE-FX MMF SC

Converter, 2km

FVT-2002

10/100BASE-TX to 100BASE-FX MMF ST

Converter, 2km

FVT-2201

10/100BASE-TX to 100BASE-FX SMF SC

Converter, 20km

FVT-2401

10/100BASE-TX to 100BASE-FX SMF SC

Converter, 40km

GVT-2000

10/100/1000BASE-T to 1000BASE-X SFP

Converter

GVT-2001

10/100/1000BASE-T to 1000BASE-SX MMF SC

Converter, 550m

Ver. 1.3 - 1605

Table of Contents

1. INTRODUCTION...................................................1

1.1. FEATURES............................................................1

1.2. PACKAGE CONTENTS ...........................................2

2. HARDWARE DESCRIPTION ..............................3

2.1. FRONT PANEL......................................................3

2.2. REAR PANEL........................................................ 4

2.3. LED INDICATORS ................................................5

2.4. DIP-SWITCH......................................................... 7

3. CABLING ................................................................9

4. SPECIFICATION ................................................. 11

5. OPTIONAL SFP MODULES............................... 13

1. Introduction

LevelOne media converters are Fast Ethernet 10/100Base-TX to

100Base-FX and 10/100/1000Base-T to 1000Base-SX/LX

converters to provide the flexibility required in network integration.

The TX port auto-sense connection speed, auto-negotiates half/full

duplex modes and auto-selects MDIX media type. The fiber

connectors come with multimode or singlemode, SC, ST or SFP

connector to provide necessary connection interface and distance

capabilities.

LevelOne have designed 19” racks to organize media converters the

smart way by providing a single power supply. With the

Plug-and-play technology, the converter is easy to set-up and run.

For simple, cost-effective network design, LevelOne converter

series is the perfect solution to bridge the complex network

infrastructure.

1.1. Features

Fast Ethernet Module

Comply with IEEE 802.3, 802.3u and 802.3x standards.

Convert between UTP cabling and Fiber-optic cabling.

One RJ-45 connector, Auto-MDI/MDIX for UTP port.

Support 10/100 Mbps Auto-negotiation for UTP port.

Fiber cabling connectivity up to 40Km.

Store-and-forward switching to separate two collision domains.

One fiber connector (SC/ ST) for 100Base-FX.

6 DIP-switches to set the operation mode

Link- Lost-Forwarding function.

Gigabit Ethernet Module

Comply with IEEE 802.3, 802.3u and 802.3x, IEEE 802.3ab

1000BaseT, 802.3z 1000Base SX/LX standards.

Convert between UTP cabling and Fiber-optic cabling.

One RJ-45 connector, Auto-MDI/MDIX for UTP port.

Support 10/100/1000 Mbps Auto-negotiation for UTP port

Fiber cabling connectivity up to 80Km.

Store-and-forward switching to separate two collision domains.

One fiber connector (SC / SFP) for 1000Base-SX/LX

DIP-switches to set the operation mode function.

Link- Lost-Forwarding function.

1.2. Package Contents

- Stand-alone Media Converter

- Power Adapter (10/100M 5V,1A; 10/100/1000M 5V,2A)

- User Manual

Compare the contents of your converter module with the checklist

above. If any item is damaged or missing, please contact your local

dealer for service.

2. Hardware Description

2.1. Front Panel

FVT-2001 / FVT-2002 / FVT-2201 / FVT-2401

GVT-2000

GVT-2001

(1) RJ-45 Port (3) Fiber/SFP Connector

(2) LED Indicators (4) DIP-Switch

2.2. Rear Panel

Power Adapter: (10/100M DC 5V, 1A; 10/100/1000M DC 5V, 2A)

The rear panel contains a power socket. This power socket accepts

DC 5V voltage and minimum 1A & 2A supplied current.

2.3. LED Indicators

Fast Ethernet Module

LED

Status

Meaning

PWR

Power on

FX 100

100Mbps Fiber Speed

TX 100

100Mbps UTP Speed

OFF

10 Mbps UTP Speed

FDX

Converter works in the full duplex mode

OFF

Converter works in the half duplex mode

LINK/ACT

Connection status display for fiber link.

“ON”indicates that Fiber link is in correct

connection.

Blinks

Active status display of fiber link

“Blink”indicates packet goes through FX end.

LINK/ACT

Connection status display for electric link.

“ON”indicates that electric link is in correct

connection.

Blinks

Active status display of fiber link

“Blink”indicates packet goes through TX end

Gigabit Ethernet Module

LED

Status

Meaning

PWR

Power on

1000

1000Mbps UTP Speed

100

100Mbps UTP Speed

FDX

Converter works in the full duplex mode

Off

Converter works in the half duplex mode

LINK/ACT

(UTP)

Blinks

Active status display of electrical interface link

Blink” indicates packet goes through TP

LNK/ACT

(Fiber)

Blinks

Active status display of fiber interface link

“Blink” indicates packet goes through FX

Note: The UTP port speed is 10Mbps when both 100 and 1000 LED indicators

"OFF"

DIP-switch

The DIP-switch is used to configure operation mode for LLF (Link

Lost Forwarding) and operation mode for UTP/Fiber port. The

default value of DIPswitch is OFF.

Fast Ethernet Module

Status

Description

LFP is Enable

OFF

LFP is Disable

Modified cut-through switch mode is enable

OFF

Store and forward switch is enable

force the TX port work 10/100Mbps,full/half

duplex

OFF

auto-negotiation mode is enable

TX is 10Mbps

OFF

TX is 100Mbps

TX is half duplex

OFF

TX is full duplex

Normally close

Gigabit Ethernet Module

Status

Description

LFP Enable

OFF

LFP Disable

Pin 2 Pin3

OFF

Pass through

Smart pass through

OFF

Modified cut through

Store and forward

Link Lost Forwarding:

When LLF is enable, allow UTP link failures to be reported to the

fiber side and also allow Fiber link failure to be reported to the UTP

side. Therefore, A link loss forward feature is provided in both UTP

and Fiber side.

Pure Converter mode (Gigabit Ethernet Module):

When pure converter mode is enabling (on), it operates with the

minimum latency. The transmission flow does not wait until entire

frame is ready, but instead it forwards the received data immediately

after the data being received. And TP port should be forced at1000M

in this application. When DIP-Switch is in Switch Converter mode

(off), the converter function is same as Switch Hub.

Note:

Please don’t change the DIP-switch setting when UTP or fiber port is

transmitting or receiving data. It may cause some data error.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LevelOne Medienkonverter Handbücher

LevelOne

LevelOne FVT-2001 Bedienungsanleitung

LevelOne

LevelOne IEC-1800 Bedienungsanleitung

LevelOne

LevelOne FVT-1101 Bedienungsanleitung

LevelOne

LevelOne Infinity IEC-1400 Bedienungsanleitung

LevelOne

LevelOne GVT-2010 Bedienungsanleitung

LevelOne

LevelOne VDS-0200 Handbuch

LevelOne

LevelOne Infinity IEC-2001 Bedienungsanleitung

LevelOne

LevelOne IEC-1300 Bedienungsanleitung

LevelOne

LevelOne FVT-2202 Bedienungsanleitung

LevelOne

LevelOne FVS-3800 Bedienungsanleitung

LevelOne

LevelOne VDS-1201 Bedienerhandbuch

LevelOne

LevelOne POI-2001 Bedienungsanleitung

LevelOne

LevelOne VDS-0201 Bedienungsanleitung

LevelOne

LevelOne Infinity IEC-1240 Bedienungsanleitung

LevelOne

LevelOne FVT-6001 Bedienungsanleitung

LevelOne

LevelOne FVT-2000 Bedienungsanleitung

LevelOne

LevelOne VDS-1201 Bedienungsanleitung

LevelOne

LevelOne IEC-1420 Bedienungsanleitung

LevelOne

LevelOne GVT-2000 Bedienungsanleitung

LevelOne

LevelOne FVT-5001 Bedienungsanleitung

LevelOne

LevelOne IEC-1220 Bedienungsanleitung

LevelOne

LevelOne VDS-0110 Bedienungsanleitung

LevelOne

LevelOne Infinity IEC-2000 Bedienungsanleitung

LevelOne

LevelOne FVM-1101 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung