Leviton Opt-X 5WMNT-1C Bedienungsanleitung

Instructions for Use - Opt-X®Mini Wallmount Enclosure

Leviton Network Solutions, a division of Leviton Mfg. Co., Inc.

Tech Support: 1.800.824.3005 E-mail: [email protected] Web: www.leviton.com

MTP®is a registered trademark of US Conec, Ltd.

Page 1 of 30

DI-000-5WMNT-20B

5WMNT-01C

FIBER CONNECTOR SAFETY WARNINGS

SAFETY INFORMATION

• Always wear safety glasses.

• Isopropyl alcohol is ammable and may cause eye irritation. In case of contact with eyes, ush with water for at least

15 minutes. When using isopropyl alcohol, always assure proper levels of ventilation. In case of ingestion, consult a

physician immediately.

• Never look directly into a laser light source, point source at a person’s eyes, or point source at reective surfaces.

• When working on a ber link, always turn laser source off, or disconnect completely.

• Always dispose of ber debris properly, preferably using sticky tabs.

• Do not place food or beverages in the vicinity of the work area.

• Thoroughly wash face and hands after terminating ber.

• Carefully remove any ber debris that may have been stuck to clothing, or left in work area, and

dispose of properly.

TIPS AND RECOMMENDATIONS

• Using isopropyl alcohol, thoroughly clean exposed ber and buffer ensuring both are free from dust, oil,

and debris.

• Do not lay ferrule dust covers on a dirty or dusty surface.

• Always use proper tools and/or accessories to terminate bers and clean connector tips.

QUICK START GUIDE

The following instructions will help you quickly install your Leviton Opt-X®Mini Wallmount Enclosure for use in your

equipment cabinet or rack. For detailed information on each step, go to the page number listed below.

Safety Instructions Pg. 2

Quick Start Guide Pg. 2

Equipment Overview Pg. 3

Standard Accessories Pg. 3

Optional Accessories Pg. 3

Required Hardware and Tools Pg. 4

Congurations Pg. 4

• Adapter Plates

• Splicing

• SDX Cassette

Mounting Instructions Pg. 5

• Wall Mount

• Din Rail

• Zero RU

• Horizontal Pathway Mounting

• Stacking Multiple Units

Grommet Preparation Pg. 7

Cable Installation Applications Pg. 8

• Adapter Plates

• SDX Cassette

• Splicing

• Copper

• Patch Cord Installation

Labeling Pg. 10

Page 2 of 30 DI-000-5WMNT-20B

Page 3 of 30

DI-000-5WMNT-20B

1. Mounting Eyelets

2. Adhesive back wire management saddles

3. 6 ber splice sleeve holder

4. Splice Sleeve Holder locator

5. Cable Lacing point

6. Door Plunger/grommet

7. Pass though knockout

8. Cable entrance grommet

9. Zero RU Mounting slots

10. Door mounting PEM

11. SDX Bulkhead Mounting point

12. Optional lock knockout blank

13. Din Rail Bracket mounting point

14. Patch Cord Management Saddle Mounting Point

EQUIPMENT OVERVIEW

Description Image Qty in Kit

Port Identication Label 1

Wire Management

Saddles 2

5" Velcro 2

Grommets 2

#10 Wood Screw 4

Splice Sleeve Holder 4

Door Latch Plunger 2

Patch Cord

Management Saddles 2

Standard Accesories

Optional Accesories

Lock and Key 5L000-KAL

Din Rail Mounting Kit DNRAL-ACC

40mm Splice Sleeves (50 pk) FSSSD-040

Set of 4 Magnets 41030-SMJ

0RU Mounting Bracket 5WMNB-ACC

Page 4 of 30

DI-000-5WMNT-20B

REQUIRED HARDWARE AND TOOLS

Mounting screws, wall anchors, washers as appropriate

Small Magnetic Torpedo level

Powered drill or screw driver

Scissors or safety blade utility knife

#8 x 1/4" machine threaded screws (if stacking multiple enclosures)

Double-sided Adhesive Tape *sold seperately (if using the optional magnet kit)

CONFIGURATIONS

There are three possible congurations using the mini enclosure. Adhesive Backed Wire Management Saddles and

Splice Sleeve Holders should be placed as shown for each conguration.

1) Field or Pre-terminated cabling used with SDX adapter plates

2) Use with pre-terminated MTP cabling and SDX cassettes

3) Pigtail splicing used with SDX adapter plates

Page 5 of 30

DI-000-5WMNT-20B

DIN RAIL MOUNTING

MOUNTING INSTRUCTIONS

1) Determine the location to mount the enclosure. Use the following considerations in selecting a mounting location:

a) Appropriate mounting base per applicable codes and Authority Having Jurisdiction (AHJ).

b) Space around the enclosure to open the door and route patch cables. Additional space consideration is

required to open the door when stacking enclosures.

c) Adequate space above or below the enclosure to maintain industry standard bend radius compliance of all

cables entering the enclosure.

2) Using a level, place the enclosure at the target mounting location and mark the four mounting hole positions.

3) Install the top two screws and verify the enclosure is level during nal tightening of screws.

4) Install the bottom two screws.

Follow instructions provided with the DIN Rail Mounting Kit (DNRAL-ACC).

ZERO RU MOUNTING

RACK OR CABINET RAIL INSTALLATION (with Zero RU Mounting Bracket Kit #5WMNB-ACC)

1) Determine target location for mounting.

2) Determine inward or outward mounting bracket orientation.

3) Using #12-24 (or other appropriately sized) rack mounting screws, attach (1) mounting bracket to rack rail. (Figure 1)

4) Using provided #8 screws and washers provided in the mounting bracket kit, secure enclosure base to

bracket. (Figure 2)

WALL MOUNTING

RACK OR CABINET RAIL INSTALLATION (with Set of 4 Magnet Kit #41030-SMJ)

1) Determine target location for mounting.

2) Attach double sided tape to each of the 4 magnets.

3) Attach the magnet assemblies to the locations as shown in Figure 3

4) Afx the enclosure to the target location.

Figure 1 Figure 2

Page 6 of 30 DI-000-5WMNT-20B

STACKING MULTIPLE UNITS

Up to three units can be joined and mounted together. Quantity (2) #8 x ¼” machine thread screws (Not Provided) are required

for stacking one enclosure to another. A maximum of three stacked Mini Enclosures is recommended.

1) Determine target location for mounting.

2) If passing cable from one enclosure to another, remove the metal knock-out tabs on the door of the rear-most enclosure

(Enclosure #1) and the base of the top enclosure (Enclosure #2) before mounting.

3) Install the rst enclosure (Enclosure #1) to the wall in that target location.

4) Position the second enclosure directly over the rst, positioning the door plungers of Enclosure #1 through the provided

openings in the base of Enclosure #2.

5) Install #8 screws through the base of Enclosure #2 into the threaded receiving holes in the cover of Enclosure #1 and secure

to hand tightened torque.

LADDER RACK INSTALLATION (with Zero RU Mounting Bracket Kit #5WMNB-ACC)

1) Determine target location for mounting.

2) Install one mounting bracket each at the two corners using the #8 screws and washers provided in the mounting

bracket kit. (Figure 4)

3) Hang the assembled unit over the ladder rack side rail as shown in Figure 5.

NOTE: Installation of Edge Guard protective material is recommended when routing cable from one stacked enclosure to

another. Edge guard material should install to a thickness range of 0.113" to 0.130".

Figure 3

Figure 4 Figure 5

Page 7 of 30

DI-000-5WMNT-20B

Cable Grommets are provided and designed for use at both trunk and patch cord entrance points to the enclosure.

GROMMET PREPARATION AND USE

There are several options in conguring the grommets. When patching, it is recommended to cut a channel at the front of the

grommet to easily install patch cords. When routing trunks it may be desired to cut a channel at the rear of the grommet to

allow for grommet removal for adding additional trunk cables. Grommet pass through material can either be slit to limit dust and

water ingress or removed entirely. To congure a grommet, use the following cutting methods:

1) Determine required opening in cable entrance grommet

2) Determine whether slitting or removing material will be performed

3) Using a sharp-edged tool, cut the appropriate opening in using the scored marking lines as shown in Figure 6

4) Optional – cut a channel through the outer wall of the grommet for either trunk or patch cord routing.

Cable description (based on 50% ll) Diameter in inches Diameter in MM Qty per small grommet

Micro Data Center 12s Plenum 0.16 4.06 15

Micro Data Center 24s Plenum 0.18 4.57 12

Micro Data Center 48s Plenum 0.231 5.87 7

Micro Data Center 72s Plenum 0.275 6.99 5

Micro Data Center 144s Plenum 0.36 9.14 3

Trunks 12s Distribution/Loose Tube 0.18 4.57 12

Trunks 24s Distribution/Loose Tube 0.38 9.65 3

Trunks 48s Distribution/Loose Tube 0.38 9.65 3

Trunks 72s Distribution/Loose Tube 0.44 11.18 2

Trunks 144s Distribution/Loose Tube 0.69 17.53 1

Trunks 12s Armored - MDP 0.495 12.57 2

Trunks 24s Armored - MDP 0.495 12.57 2

Trunks 48s Armored - MDP 0.584 14.83 1

Trunks 72s Armored - MDP 0.594 15.09 1

Trunks 144s Armored - MDP 0.708 17.98 1

Trunks 12s Armored - All types 0.55 13.97 1

Trunks 24s Armored - All types 0.95 24.13 0

Trunks 48s Armored - All types 1.05 26.67 0

Trunks 72s Armored - All types 1.23 31.24 0

Trunks 144s Armored - All types 1.73 43.94 0

Generic UTP Copper Cat 5e 0.185 4.70 11

Generic UTP Copper Cat 6 0.23 5.84 7

Generic UTP Copper Cat 6A 0.33 8.38 4

Figure 6

ROUTING FOR BULK CABLE – FIELD TERMINATION

Page 8 of 30

DI-000-5WMNT-20B

ROUTING FOR PRE-TERMINATED CABLING

CABLE INSTALLATION

1) Feed incoming cable(s) through the grommet opening.

2) Remove required outer cable jacket leaving jacket at the closest lance point.

3) Secure the cable to the lance point with Velcro or nylon tie wraps as appropriate.

4) Using the cable management saddles, route the breakout ber legs to the patching or termination point as shown in the

conguration drawings below:

ROUTING FOR SPLICE TERMINATION

12-Fiber Splicing

24-Fiber Splicing

Page 9 of 30

DI-000-5WMNT-20B

NOTE: Maximum splice sleeve length is 40mm. The recommended part number is FSSSD-040

ROUTING FOR COPPER APPLICATIONS

LABELING

A Port Identication Label is provided with each Wall Mount Enclosure. The label(s) should be afxed to the inside of the

patch bay door. Labeling within the slot position cells can be achieved with printed labels or via excel based spreadsheets

available via download at www.leviton.com.

NOTE: Ensure that the label surface area is clean

of dirt, oil, and debris. Recommend use of isopropyl

alcohol or a simple soap and water solution when

wiping down surface area.

Page 10 of 30

DI-000-5WMNT-20B

PATCH CORD INSTALLATION

Inhaltsverzeichnis

Sprachen:

Andere Leviton Gehäuse Handbücher

Leviton

Leviton Rhino-hide 15 Series Bedienungsanleitung

Leviton

Leviton LP8 Series Bedienungsanleitung

Leviton

Leviton 5R1UH-S08 Bedienungsanleitung

Leviton

Leviton 47617-REB Bedienungsanleitung

Leviton

Leviton LP3-MC Series Bedienungsanleitung

Leviton

Leviton Opt-X Ultra 5R1UH-S03 Bedienungsanleitung

Leviton

Leviton LP8 Series Bedienungsanleitung

Leviton

Leviton Opt-X 1000i Bedienungsanleitung

Leviton

Leviton 5R1UD-S12 Bedienungsanleitung

Leviton

Leviton 17A00 Bedienungsanleitung

Leviton

Leviton 5R4UD-S48 Bedienungsanleitung

Leviton

Leviton Opt-X 5WMNT-01C Bedienungsanleitung

Leviton

Leviton 49605-14P Bedienungsanleitung

Leviton

Leviton Opt-X 5R1UD-S08 Bedienungsanleitung

Leviton

Leviton LP2 Series Bedienungsanleitung

Leviton

Leviton Opt-X 5WSML-02C Bedienungsanleitung

Leviton

Leviton Opt-X 500i Bedienungsanleitung

Leviton

Leviton Wetguard COVER-S Bedienungsanleitung

Leviton

Leviton 5R1UM-S08 Bedienungsanleitung

Leviton

Leviton LP 3B Series Bedienungsanleitung

Leviton

Leviton Opt-X 5WMED-04C Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Nexans

Nexans WTC05 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung