LG THERMA V Bedienungsanleitung

ENGLISH

Air-to-Water Heat Pump

IMPORTANT

• Please read this owner's manual carefully and

thoroughly before installing and operating your

Air-to-Water Heat Pump.

• Please retain this owner's manual for future

reference after reading it thoroughly.

Owner's Manual

Dear Owner

Thank you for installing LG Air-to-Water Heat Pump.

Your best choice guarantees you a great

performance and service to make your life

comfortable & pleasant.

2Air-to-Water Heat Pump Owner’s Manual

Air-to-Water Heat Pump Owner’s Manual

TABLE OF CONTENTS

FOR YOUR RECORDS

Write the model and serial numbers here:

Model #

Serial #

You can find them on a label on the side of each

unit.

Installer's Name

Purchased Date

■

Staple your receipt to this page in the event you

need it to prove date of purchase or for warranty

issues.

READ THIS MANUAL

Inside you will find many helpful hints on how to use and

maintain your AWHP properly. Just a little preventive

care on your part can save you a great deal of time and

money over the life of your product.

You'll find many answers to common problems in the

chart of troubleshooting tips. If you review our chart of

Troubleshooting Tips first, you may not need to call for

service at all.

PRECAUTION

•Contact the authorized service technician for repair or

maintenance of this unit.

• Contact the installer for installation of this unit.

• AWHP is not intended for use by young children or

invalids without supervision.

• Young children should be supervised to ensure that

they do not play with AWHP.

• When the power cable is to be replaced, replacement

work shall be performed by authorized personnel only

using only genuine replacement parts.

• Installation work must be performed in accordance

A. Safety Precautions.........................3

B. Product Introduction......................6

C. Installation instruction...................8

D. Owner's instruction......................36

E. Using Thermostat.........................63

F. Maintenance and Service.............67

G. Disposal Requirements ...............69

Safety Precaution

Owner’s Manual 3

ENGLISH

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed.

■Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by

the following indications.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage.

WARNING

Always ground the product.

• There is a risk of electric shock.

Do not use a defective or underrated

circuit breaker. Use the correctly rated

breaker and fuse.

• There is risk of fire or electric shock .

Do not use a multi outlet. Always use

this appliance on a dedicated circuit and

breaker.

• Otherwise it can cause electric shock or fire.

For electrical work, contact the dealer, seller,

a qualified electrician, or an Authorized

Service Center. Do not disassemble or repair

the product by yourself.

• There is risk of fire or electric shock.

Always ground the product as per the

wiring diagram. Do not connect the

ground wire to gas or water pipes

lightening rod or telephone ground wire.

• There is risk of fire or electric shock.

Install the panel and the cover of control

box securely.

• There is risk of fire or electric shock due to

dust , water etc.

Use the correctly rated breaker or fuse.

• There is risk of fire or electric shock.

Do not modify or extend the power

cable. If the power cable or cord has

scratches or skin peeled off or

deteriorated then it must be replaced.

• There is risk of fire or electric shock.

For installation, removal or reinstall ,

always contact the dealer or an

Authorized Service Center.

• There is risk of fire, electric shock, explosion,

or injury.

Do not install the product on a defective

installation stand. Be sure that the

installation area does not deteriorate with

age.

• It may cause product to fall.

Never install the outdoor unit on a

moving base or a place from where it

can fall down.

• The falling outdoor unit can cause damage

or injury or even death of a person.

When the product is soaked (flooded or

submerged) in water , contact an

Authorized Service Center for repair

before using it again.

• There is risk of fire or electric shock.

Be sure to check the refrigerant to

be used. Please read the label on the

product.

• Incorrect refrigerant can prevent the normal

operation of the unit.

Don't use a power cord, a plug or a

loose socket which is damaged.

• Otherwise it may cause a fire or electrical

shock.

Do not touch , operate, or repair

the product with wet hands.

• There is risk of electric shock or fire.

Do not place a heater or other heating

appliances near the power cable.

• There is risk of fire and electric shock.

Do not allow water to run into electric

parts. Install the unit away from water

sources.

• There is risk of fire, failure of the product, or

electric shock.

Do not store or use or even allow

flammable gas or combustibles near the

product.

• There is risk of fire.

Safety Precaution

4Air-to-Water Heat Pump Owner’s Manual

Indoor/outdoor wiring connections must

be secured tightly and the cable should

be routed properly so that there is no

force pulling the cable from the

connection terminals.

• Improper or loose connections can cause

heat generation or fire.

Safely dispose off the packing materials.

Like screws, nails, batteries, broken

things etc after installation or service

and then tear away and throw away the

plastic packaging bags.

• Children may play with them and cause

injury.

Make sure to check that the power

device is not dirty, loose or broken and

then Turn on the power.

• Dirty, loose or broken power device can

cause electric shock or fire.

Do not use the product in a tightly

closed space for a long time. Perform

ventilation regularly.

• Oxygen deficiency could occur and hence

harm your health.

Do not open the front cover or grille of the

product during operation. (Do not touch the

electrostatic filter, if the unit is so equipped.)

• There is risk of physical injury, electric

shock, or product failure.

If strange sounds, smell or smoke comes

from product, immediately turn the breaker

off or disconnect the power supply cable.

• There is risk of electric shock or fire.

Ventilate the product room from time to

time when operating it together with a

stove, or heating element etc.

• Oxygen deficiency can occur and hence

harm your health.

Turn the main power off when cleaning

or repairing the product.

• There is risk of electric shock.

Take care to ensure that nobody

especially kids could step on or fall onto

the outdoor unit.

• This could result in personal injury and

product damage.

Take care to ensure that power cable

could not be pulled out or damaged

during operation.

• There is risk of fire or electric shock.

Do not place ANYTHING on the power

cable.

• There is risk of fire or electric shock.

When flammable gas leaks, turn off the

gas and open a window for ventilation

before turn the product on.

• Do not use the telephone or turn switches on

or off. There is risk of explosion or fire.

In outdoor unit the step-up capacitor

supplies high voltage electricity to the

electrical components. Be sure to

discharge the capacitor completely

before conducting the repair work.

• An charged capacitor can cause electrical

shock.

When installing the unit, use the

installation kit provided with the product.

• Otherwise the unit may fall and cause severe

injury.

Be sure to use only those parts which

are listed in the service parts list. Never

attempt to modify the equipment.

• The use of inappropriate parts can cause an

electrical shock, excessive heat generation

or fire.

Safety Precaution

Owner’s Manual 5

ENGLISH

CAUTION

Two or more people must lift and

transport the product.

• Avoid personal injury.

Do not install the product where it will be

exposed to sea wind (salt spray) directly.

• It may cause corrosion on the product.

Keep level even when installing the

product.

• To avoid vibration or noise.

Do not install the product where the noise

or hot air from the outdoor unit could

damage or disturb the neighborhoods.

• It may cause a problem for your neighbors

and hence dispute.

Always check for gas (refrigerant)

leakage after installation or repair of

product.

• Low refrigerant levels may cause failure of

product.

Do not use the product for special

purposes, such as preserving foods,

works of art, etc. It is a consumer AWHP,

not a precision refrigeration system.

• There is risk of damage or loss of property.

Do not block the inlet or outlet of air

flow.

• It may cause product failure.

Use a soft cloth to clean. Do not use

harsh detergents, solvents or splashing

water etc .

• There is risk of fire, electric shock, or

damage to the plastic parts of the product.

Do not step on or put anyting on the

product. (outdoor units)

•

There is risk of personal injury and failure of product.

Do not insert hands or other objects

through the air inlet or outlet while the

product is operating.

• There are sharp and moving parts that could

cause personal injury.

Be cautious when unpacking and

installing the product.

• Sharp edges could cause injury.

If the refrigerant gas leaks during the

repair, do not touch the leakaing

refrigerant gas.

• The refrigernat gas can cause frostbite (cold

burn)

Do not tilt the unit when removing or

uninstalling it.

• The condensed water inside can spill .

Do not mix air or gas other than the

specified refrigerant used in the system .

• If air enters the refrigerant system, an

excessively high pressure results, causing

equipment damage or injury.

If the refrigerant gas leaks during the

installation, ventilate the area immediately.

• Otherwise it can be harmfull for your health.

Dismantling the unit, treatment of the

refrigerant oil and eventual parts should

be done in accordance with local and

national standards.

Do not expose your skin or kids or

plants to the cool or hot air draft.

• This could harm to your health.

Use a firm stool or ladder when cleaning,

maintaining or repairing the product at

an height.

• Be careful and avoid personal injury.

6Air-to-Water Heat Pump Owner’s Manual

Product Introduction

1. Indoor unit

2. Outdoor unit

3. Refrigerant pipe and connecting cable

4. Water pipe

5. Ground wire to ground outdoor unit to prevent electrical shocks.

The shape of products can be chaged according to the model capacity and type.

Water

Inlet

Water

Outlet

Typical Installation Scene

Product Introduction

Owner’s Manual 7

ENGLISH

❊Some functions may not be operated and displayed depending on the model.

Control Panel

1. Display panel

2. Change temperature button

3. Silent mode On/Off button

4. Operation mode selection button

5. Water heating Enable/Disable

button

6. ESC button

7. Direction button

(Up, Down, Left, Right)

8. Power button

9. Function setting button

10. Temperature setting button

11. Temperature view button

12. Programming button

13. Set/Clear button

8Air-to-Water Heat Pump Owner’s Manual

Installer setting mode is to set the detail function of the control panel.

If the installer setting mode is not set correctly, it could cause problems to the product, user

injury or property damage. This must be set by an certificated installer, and any installation or

change that is carried out by a non-certificated person should be responsible for the results. In

this case, free service cannot be provided.

CAUTION

Installation instruction

Installer Setting -How to enter installer setting mode

Press Function Setting button for 3

seconds to enter

the installer setting mode.

(When you enter the installer setting

mode initially, Function code is displayed

on the bottom of the LCD screen.)

Repeat pressing button, and the function

code will be changed from 01 to 2A.

Please refer the code table on the next

page.

Function Code Value

Owner’s Manual 9

ENGLISH

Installation instruction

Installer Setting -Installation Function Code Table

Function Code

Example of Function Code Display

Value #1 Value #2

■Installation Function Code Table

Code Item Detail Remark

1 Function Test Run

Description Instant cooling operation for charging additional refrigerant

Value #1 Note -

Default -

Range -

Value #2 Note -

Default -

Range -

2 Function Disable 3 Min. Delay

Description Factory use only

Value #1 Note -

Default -

Range -

Value #2 Note -

Default -

Range -

3 Function Remote Air Sensor Connection

Description Connection information about remote air sensor

Value #1 Note 01:Remote air sensor is NOT connected and NOT used

02:Remote air sensor is connected and used

Default 1

Range 01~02

Value #2 Note -

Default -

Range -

4 Function Celsius/Fahrenheit Switching

Description Display temperature in Celsius or Fahrenheit

Value #1 Note 01:Celsius

02:Fahrenheit

Default 1

Range 01~02

Value #2 Note -

Default -

Range -

Installation instruction

10 Air-to-Water Heat Pump Owner’s Manual

Code Item Detail Remark

5 Function Setting Temperature Selection

Description Selection for setting temperature as air temperature or

leaving water temperature

Value #1 Note 01:Air temperature

02:Leaving water temperature

Air temperature as setting temperature is ONLY available

when remote air sensor

Connection is enabled and Function Code 03 is set as 02.

Default 2

Range 01~02

Value #2 Note -

Default -

Range -

6 Function Auto Dry Contact

Description Setting dry contact auto start option

Value #1 Note 01:Auto Start OFF

02:Auto Start ON

Default 2

Range 01~02

Value #2 Note -

Default -

Range -

7 Function Address Setting

Description Assigning address when central controller is installed

Value #1 Note -

Default -

Range -

Value #2 Note -

Default -

Range -

11 Function Setting Air Temperature in Cooling Mode

Description Adjusting range of 'Setting Air Temperature' in cooling mode

Value #1 Note Upper Limit of setting range

Default 30°C

Range 24~30°C

Value #2 Note Lower Limit of setting range

Default 18°C

Range 18~22°C

12 Function Setting Leaving Water Temperature in Cooling Mode

Description Adjusting range of 'Setting Leaving Water Temperature' in

cooling mode

Value #1 Note Upper Limit of setting range

Default 24°C

Range 20~25°C

Value #2 Note Lower Limit of setting range(FCU is equipped)

Default 06°C

Range 06~18°C

'Setting Air

Temperature' is

used when user

wants to set target

temperature by

room air

temperature.

'Setting Leaving

Water

Temperature' is

used when user

wants to set target

temperature by

leaving(from the

indoor unit) water

temperature.

Andere Handbücher für THERMA V

Inhaltsverzeichnis

Andere LG Wärmepumpe Handbücher

LG LD097HV4 Installations- und Betriebshandbuch

LG Therma V ZHBW056A0 Bedienungsanleitung

LG ARUV025GSD0 Produkthandbuch

LG LMU247HV Bedienungsanleitung

LG Multi V CRNN-SP Series Bedienungsanleitung

LG THERMA V AHUW126A3 Bedienungsanleitung

LG ARNU07GB1G1 Bedienungsanleitung

LG Multi V III Solo ARUN LM3 Series Bedienungsanleitung

LG Hydro Kit Bedienungsanleitung

LG MULTI V ARUN072BTE4 Bedienungsanleitung

LG Multi IV Installations- und Betriebshandbuch

LG MULTI V LRNN Series Bedienungsanleitung

LG Hydro Kit IWT Bedienungsanleitung

LG MULTI F Series Installations- und Betriebshandbuch

LG AHNW146A0 Bedienungsanleitung

LG Hydro Kit ARNH30GK1A4 Bedienungsanleitung

LG LC098HV4 Installations- und Betriebshandbuch

LG MULTI V ARUN050LMS0 Produkthandbuch

LG Therma V PHLLA Bedienungsanleitung

LG ATNW18GTLP1 Produkthandbuch

LG MULTI V B2 Series Bedienungsanleitung

LG WH20S F5 Bedienungsanleitung

LG A2UW18GFAC Bedienungsanleitung

LG THERMA V Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung